Y en a long, et ça ne semble pas très prometteur :
smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.7.7-200.fc39.x86_64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01UBD... (USB 3.0)
Device Model: TOSHIBA MQ01UBD100
Serial Number: 236XS3RES
LU WWN Device Id: 0 000000 000000000
Firmware Version: AX001U
User Capacity: 1 000 204 886 016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database 7.3/5528
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu Mar 14 08:36:37 2024 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 247) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 099 099 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 2544
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 13940
5 Reallocated_Sector_Ct 0x0033 001 001 050 Pre-fail Always FAILING_NOW 16376
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 059 059 000 Old_age Always - 16569
10 Spin_Retry_Count 0x0033 253 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1718
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 2
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 82
193 Load_Cycle_Count 0x0032 096 096 000 Old_age Always - 47026
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 24 (Min/Max 9/56)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 174
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
222 Loaded_Hours 0x0032 099 099 000 Old_age Always - 503
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 187
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 6752 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 6752 occurred at disk power-on lifetime: 16569 hours (690 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 68 fc 14 4b Error: UNC 8 sectors at LBA = 0x0b14fc68 = 185924712
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 68 fc 14 40 00 15:48:20.200 READ DMA EXT
35 00 08 00 08 00 40 00 15:48:20.171 WRITE DMA EXT
25 00 08 00 08 04 40 00 15:48:20.136 READ DMA EXT
25 00 08 f8 07 04 40 00 15:48:20.102 READ DMA EXT
25 00 08 08 29 00 40 00 15:48:20.096 READ DMA EXT
Error 6751 occurred at disk power-on lifetime: 16561 hours (690 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 00 08 d4 40 Error: UNC 8 sectors at LBA = 0x00d40800 = 13895680
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 00 08 d4 40 00 08:01:01.808 READ DMA EXT
35 00 80 00 08 80 40 00 08:01:01.751 WRITE DMA EXT
25 00 08 00 08 d4 40 00 08:00:57.981 READ DMA EXT
35 00 80 00 08 40 40 00 08:00:57.958 WRITE DMA EXT
25 00 08 00 08 84 40 00 08:00:57.944 READ DMA EXT
Error 6750 occurred at disk power-on lifetime: 16561 hours (690 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 00 08 d4 40 Error: UNC 8 sectors at LBA = 0x00d40800 = 13895680
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 00 08 d4 40 00 08:00:57.981 READ DMA EXT
35 00 80 00 08 40 40 00 08:00:57.958 WRITE DMA EXT
25 00 08 00 08 84 40 00 08:00:57.944 READ DMA EXT
35 00 80 00 08 00 40 00 08:00:57.575 WRITE DMA EXT
25 00 08 00 08 2c 40 00 08:00:57.560 READ DMA EXT
Error 6749 occurred at disk power-on lifetime: 16561 hours (690 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 00 08 c4 49 Error: UNC 8 sectors at LBA = 0x09c40800 = 163842048
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 00 08 c4 40 00 08:00:53.697 READ DMA EXT
35 00 80 00 08 c0 40 00 08:00:53.357 WRITE DMA EXT
35 00 80 00 08 80 40 00 08:00:53.306 WRITE DMA EXT
25 00 08 00 08 c4 40 00 08:00:49.524 READ DMA EXT
35 00 f0 f0 08 44 40 00 08:00:49.472 WRITE DMA EXT
Error 6748 occurred at disk power-on lifetime: 16561 hours (690 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 00 08 c4 49 Error: UNC 8 sectors at LBA = 0x09c40800 = 163842048
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 00 08 c4 40 00 08:00:49.524 READ DMA EXT
35 00 f0 f0 08 44 40 00 08:00:49.472 WRITE DMA EXT
25 00 08 00 08 5c 40 00 08:00:45.701 READ DMA EXT
35 00 f0 00 08 44 40 00 08:00:45.683 WRITE DMA EXT
35 00 80 00 08 40 40 00 08:00:45.627 WRITE DMA EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
The above only provides legacy SMART information - try 'smartctl -x' for more
