Bon , j'ai essayé après avoir virer les drivers proprio de faire marcher le wifi via les kmod-staging avec le module r8192_pci et ca ne fonctionne pas, donc à mon avis la case driver proprio est indispensable dans ce cas. (Non-non s'il vous plait, pas taper :hammer: )
@remixbx : ah ok !

Avant de se lancer dans la compilation du driver proprio (fox765 n'a pas encore trop l'habitude de fedora et de la compilation), on peut quand même faire le test, au cas où 😉

@fox765
Essaye alors, en root :
#modprobe r8192_pci 
#lsmod | grep r8192 (pour vérifier qu'il est chargé)
#service NetworkManger restart
#iwconfig
#ifconfig wlan0 up
Peux-tu aussi donner le résultat de
 #lspci -nn |grep Network
D'après la documentation du module (modinfo r8192_pci), la méthode devrait marcher pour les cartes/ID suivants :
PCI: 07AA:0044 (Vendor name unknown) (Device name unknown)
PCI: 07AA:0047 (Vendor name unknown) (Device name unknown)
PCI: 10EC:8192 Realtek Semiconductor Co., Ltd. RTL8192E Wireless LAN Controller
Bonjour à tous

La cata !!! Dois-je tout reprendre ??



J'ai eu le même message en essayant de lancer sous VirtualBox sous Wiindows.

Pour quelle raison ça a foiré sans raison apparente.

Je me suis refait une clé de 4 Go persistant avec Lili usb Creator sur laquelle je trafique en ce moment.

@ remixbx, j'ai bien le bon pilote:



sous 2 extensions: tar.gz et deb

Pour info, C'est le deb qui a fonctionné aussitôt sous Ubuntu

@ balustre

Je fais éventuellement les renvois demandés, mais je crains que je doive tout recréer pour qu'il y ait un résultat plausible.
[liveuser@localhost ~]$ su -
[root@localhost ~]# modprobe r8192_pci
FATAL: Module r8192_pci not found.
[root@localhost ~]# lsmod | grep r8192
[root@localhost ~]# service NetworkManger restart
NetworkManger: unrecognized service
[root@localhost ~]# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

[root@localhost ~]# ifconfig wlan0 up
wlan0: unknown interface: No such device
[root@localhost ~]# lspci -nn |grep network
[root@localhost ~]#
Heureux qu'il ne s'agissait pas d'une installation définitive, je serais alors dans des beaux draps !!

Sinon vici les caractéristiques de ma carte en question:
[liveuser@localhost ~]$ su -
[root@localhost ~]# lspci -v
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
    Subsystem: Micro-Star International Co., Ltd. Device 102c
    Flags: bus master, fast devsel, latency 0
    Capabilities: [e0] Vendor Specific Information: Len=0a <?>

00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) (prog-if 00 [Normal decode])
    Flags: bus master, fast devsel, latency 0
    Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
    I/O behind bridge: 0000e000-0000efff
    Memory behind bridge: feb00000-febfffff
    Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
    Capabilities: [88] Subsystem: Micro-Star International Co., Ltd. Device 102c
    Capabilities: [80] Power Management version 3
    Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
    Capabilities: [a0] Express Root Port (Slot+), MSI 00
    Capabilities: [100] Virtual Channel
    Capabilities: [140] Root Complex Link
    Kernel driver in use: pcieport

00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) (prog-if 00 [UHCI])
    Subsystem: Micro-Star International Co., Ltd. Device 102c
    Flags: bus master, medium devsel, latency 0, IRQ 16
    I/O ports at 9800 [size=32]
    Capabilities: [50] PCI Advanced Features
    Kernel driver in use: uhci_hcd

00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) (prog-if 00 [UHCI])
    Subsystem: Micro-Star International Co., Ltd. Device 102c
    Flags: bus master, medium devsel, latency 0, IRQ 21
    I/O ports at 9480 [size=32]
    Capabilities: [50] PCI Advanced Features
    Kernel driver in use: uhci_hcd

00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) (prog-if 00 [UHCI])
    Subsystem: Micro-Star International Co., Ltd. Device 102c
    Flags: bus master, medium devsel, latency 0, IRQ 19
    I/O ports at 9400 [size=32]
    Capabilities: [50] PCI Advanced Features
    Kernel driver in use: uhci_hcd

00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) (prog-if 20 [EHCI])
    Subsystem: Micro-Star International Co., Ltd. Device 102c
    Flags: bus master, medium devsel, latency 0, IRQ 18
    Memory at fe8fec00 (32-bit, non-prefetchable) [size=1K]
    Capabilities: [50] Power Management version 2
    Capabilities: [58] Debug port: BAR=1 offset=00a0
    Capabilities: [98] PCI Advanced Features
    Kernel driver in use: ehci_hcd

00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03)
    Subsystem: Micro-Star International Co., Ltd. Device 102c
    Flags: bus master, fast devsel, latency 0, IRQ 31
    Memory at fe8f8000 (64-bit, non-prefetchable) [size=16K]
    Capabilities: [50] Power Management version 2
    Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
    Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00
    Capabilities: [100] Virtual Channel
    Capabilities: [130] Root Complex Link
    Kernel driver in use: HDA Intel
    Kernel modules: snd-hda-intel

00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode])
    Flags: bus master, fast devsel, latency 0
    Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
    I/O behind bridge: 0000b000-0000bfff
    Memory behind bridge: fe900000-fe9fffff
    Prefetchable memory behind bridge: 00000000fbf00000-00000000fbffffff
    Capabilities: [40] Express Root Port (Slot+), MSI 00
    Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
    Capabilities: [90] Subsystem: Micro-Star International Co., Ltd. Device 102c
    Capabilities: [a0] Power Management version 2
    Capabilities: [100] Virtual Channel
    Capabilities: [180] Root Complex Link
    Kernel driver in use: pcieport

00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) (prog-if 00 [Normal decode])
    Flags: bus master, fast devsel, latency 0
    Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
    I/O behind bridge: 0000c000-0000cfff
    Memory behind bridge: fe000000-fe7fffff
    Prefetchable memory behind bridge: 00000000fc000000-00000000fdffffff
    Capabilities: [40] Express Root Port (Slot+), MSI 00
    Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
    Capabilities: [90] Subsystem: Micro-Star International Co., Ltd. Device 102c
    Capabilities: [a0] Power Management version 2
    Capabilities: [100] Virtual Channel
    Capabilities: [180] Root Complex Link
    Kernel driver in use: pcieport

00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode])
    Flags: bus master, fast devsel, latency 0
    Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
    I/O behind bridge: 0000d000-0000dfff
    Memory behind bridge: fea00000-feafffff
    Prefetchable memory behind bridge: 00000000c0000000-00000000c01fffff
    Capabilities: [40] Express Root Port (Slot+), MSI 00
    Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
    Capabilities: [90] Subsystem: Micro-Star International Co., Ltd. Device 102c
    Capabilities: [a0] Power Management version 2
    Capabilities: [100] Virtual Channel
    Capabilities: [180] Root Complex Link
    Kernel driver in use: pcieport

00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
    Subsystem: Micro-Star International Co., Ltd. Device 102c
    Flags: bus master, medium devsel, latency 0, IRQ 23
    I/O ports at a000 [size=32]
    Capabilities: [50] PCI Advanced Features
    Kernel driver in use: uhci_hcd

00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI])
    Subsystem: Micro-Star International Co., Ltd. Device 102c
    Flags: bus master, medium devsel, latency 0, IRQ 19
    I/O ports at 9c00 [size=32]
    Capabilities: [50] PCI Advanced Features
    Kernel driver in use: uhci_hcd

00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) (prog-if 00 [UHCI])
    Subsystem: Micro-Star International Co., Ltd. Device 102c
    Flags: bus master, medium devsel, latency 0, IRQ 18
    I/O ports at 9880 [size=32]
    Capabilities: [50] PCI Advanced Features
    Kernel driver in use: uhci_hcd

00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) (prog-if 20 [EHCI])
    Subsystem: Micro-Star International Co., Ltd. Device 102c
    Flags: bus master, medium devsel, latency 0, IRQ 23
    Memory at fe8ff000 (32-bit, non-prefetchable) [size=1K]
    Capabilities: [50] Power Management version 2
    Capabilities: [58] Debug port: BAR=1 offset=00a0
    Capabilities: [98] PCI Advanced Features
    Kernel driver in use: ehci_hcd

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) (prog-if 01 [Subtractive decode])
    Flags: bus master, fast devsel, latency 0
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
    Capabilities: [50] Subsystem: Micro-Star International Co., Ltd. Device 102c

00:1f.0 ISA bridge: Intel Corporation ICH9M-E LPC Interface Controller (rev 03)
    Subsystem: Micro-Star International Co., Ltd. Device 102c
    Flags: bus master, medium devsel, latency 0
    Capabilities: [e0] Vendor Specific Information: Len=0c <?>
    Kernel modules: iTCO_wdt

00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) (prog-if 01 [AHCI 1.0])
    Subsystem: Micro-Star International Co., Ltd. Device 102c
    Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 28
    I/O ports at ac00 [size=8]
    I/O ports at a880 [size=4]
    I/O ports at a800 [size=8]
    I/O ports at a480 [size=4]
    I/O ports at a400 [size=32]
    Memory at fe8ff800 (32-bit, non-prefetchable) [size=2K]
    Capabilities: [80] MSI: Enable+ Count=1/16 Maskable- 64bit-
    Capabilities: [70] Power Management version 3
    Capabilities: [a8] SATA HBA v1.0
    Capabilities: [b0] PCI Advanced Features
    Kernel driver in use: ahci

00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03)
    Subsystem: Micro-Star International Co., Ltd. Device 102c
    Flags: medium devsel, IRQ 18
    Memory at fe8ff400 (64-bit, non-prefetchable) [size=256]
    I/O ports at 0400 [size=32]
    Kernel driver in use: i801_smbus
    Kernel modules: i2c-i801

02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
    Subsystem: Micro-Star International Co., Ltd. Device 102c
    Physical Slot: 0-1
    Flags: bus master, fast devsel, latency 0, IRQ 30
    I/O ports at b800 [size=256]
    Memory at fbfff000 (64-bit, prefetchable) [size=4K]
    Memory at fbff8000 (64-bit, prefetchable) [size=16K]
    Expansion ROM at fe9e0000 [disabled] [size=128K]
    Capabilities: [40] Power Management version 3
    Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
    Capabilities: [70] Express Endpoint, MSI 01
    Capabilities: [ac] MSI-X: Enable- Count=4 Masked-
    Capabilities: [cc] Vital Product Data
    Capabilities: [100] Advanced Error Reporting
    Capabilities: [140] Virtual Channel
    Capabilities: [160] Device Serial Number 03-00-00-00-68-4c-e0-00
    Kernel driver in use: r8169
    Kernel modules: r8169

05:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8192SE Wireless LAN Controller (rev 10)
    Subsystem: Realtek Semiconductor Co., Ltd. RTL8192SE Wireless LAN Controller
    Physical Slot: 0-3
    Flags: bus master, fast devsel, latency 0, IRQ 11
    I/O ports at d800 [size=256]
    Memory at feafc000 (32-bit, non-prefetchable) [size=16K]
    Capabilities: [40] Power Management version 3
    Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
    Capabilities: [70] Express Legacy Endpoint, MSI 00
    Capabilities: [100] Advanced Error Reporting
    Capabilities: [140] Virtual Channel
    Capabilities: [160] Device Serial Number 88-55-22-fe-ff-4c-e0-00

06:00.0 VGA compatible controller: ATI Technologies Inc M92 [Mobility Radeon HD 4500 Series] (prog-if 00 [VGA controller])
    Subsystem: Micro-Star International Co., Ltd. Device 102c
    Physical Slot: 0
    Flags: bus master, fast devsel, latency 0, IRQ 29
    Memory at d0000000 (32-bit, prefetchable) [size=256M]
    I/O ports at e000 [size=256]
    Memory at febf0000 (32-bit, non-prefetchable) [size=64K]
    [virtual] Expansion ROM at feb00000 [disabled] [size=128K]
    Capabilities: [50] Power Management version 3
    Capabilities: [58] Express Legacy Endpoint, MSI 00
    Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
    Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
    Kernel driver in use: radeon
    Kernel modules: radeon

06:00.1 Audio device: ATI Technologies Inc RV710/730
    Subsystem: Micro-Star International Co., Ltd. Device 102c
    Physical Slot: 0
    Flags: bus master, fast devsel, latency 0, IRQ 32
    Memory at febbc000 (32-bit, non-prefetchable) [size=16K]
    Capabilities: [50] Power Management version 3
    Capabilities: [58] Express Legacy Endpoint, MSI 00
    Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
    Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
    Kernel driver in use: HDA Intel
    Kernel modules: snd-hda-intel

[root@localhost ~]#
-> Les pilotes sont encore sous forme d'archive (le .deb ne servira à rien sous fedora). On les installera qu'en cas de nécessité, car cela demande de les compiler;

-> Effectivement, pour que ca ait un intéret, il faut refaire les commandes, mais c'est rapide 🙂 !

D'abord installer en root les dépot RPM fusion free et non free (regarder la page 1 si tu as un doute, mais y'a pas de difficultés)
Ensuite :
yum install kmod-staging*

si l'installation des dépots à bien marcher, l'installation ici fonctionnera !

Enfin reprendre la liste de commandes... mais si il dit encore : FATAL: Module r8192_pci not found. , ce n'est pas la peine d'aller plus loin !

Et je me suis trompée ci dessus, j'avais en fait besoin de
#lspci -nn |grep Network

pour vérifier l'ID du périphérique

-> Par ailleurs, je crois comprendre que tu utilises un Live USB. Attention, il y a des choses que tu n'as "pas le droite de faire" : comme installer un nouveau noyau... Donc si tu fais fait un update, fais attention à ne pas installer de kernel !
Bonjour balustre
D'abord installer en root les dépot RPM fusion free et non free (regarder la page 1 si tu as un doute, mais y'a pas de difficultés)
Ensuite :
yum install kmod-staging*

si l'installation des dépots à bien marcher, l'installation ici fonctionnera !
Voila, c'est fait, installation OK.
Content de voir que je me familiarise petit à petit avec les cdes de fedora
Et je me suis trompée ci dessus, j'avais en fait besoin de
#lspci -nn |grep Network
[liveuser@localhost ~]$ su -
[root@localhost ~]# lspci -nn |grep Network
05:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8192SE Wireless LAN Controller [10ec:8172] (rev 10)
[root@localhost ~]# lsmod | grep ath
[root@localhost ~]# 
[root@localhost ~]# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

[root@localhost ~]#
Qu'il aura t-il à faire ensuite ?
Je ne voudrais pas abuser de ton temps,mais c'est sympa de m'aider à trouver la soluce.
Re-bonjour !

Super, je pensais aussi que ca serait bénéfique de faire à nouveau ces commandes avec un peu plus d'habitude. Les commandes à faire sont :
#modprobe r8192_pci 
#lsmod | grep r8192 (pour vérifier qu'il est chargé. s'il ne l'est pas, inutile d'aller plus loin et faire plutôt : #modprobe -l | grep 819)
#service NetworkManger restart
#iwconfig
#ifconfig wlan0 up
PS : Pour les histoires avec ath, je m'étais trompée en confondant les deux cartes... le bon pilote pour ce PC est r8192_pci, et non ath5 (qui est pour les atheros..)

PS2 : L'ID de ta carte est [10ec:8172], et le pilote r8192_pci est dit compatible avec :
PCI: 07AA:0044 (Vendor name unknown) (Device name unknown)
PCI: 07AA:0047 (Vendor name unknown) (Device name unknown)
PCI: 10EC:8192 Realtek Semiconductor Co., Ltd. RTL8192E Wireless LAN Controller

Le problème de remixbx (seuls le pilote proprio fontcionne) peut peut-être venir de là.
les retours:
[liveuser@localhost ~]$ su -
[root@localhost ~]# modprobe r8192_pci
FATAL: Module r8192_pci not found.
[root@localhost ~]# lsmod | grep r8192
[root@localhost ~]# modprobe -l | grep 819
kernel/drivers/media/video/bt819.ko
[root@localhost ~]# service NetworkManger restart
NetworkManger: unrecognized service
[root@localhost ~]# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

[root@localhost ~]# ifconfig wlan0 up
wlan0: unknown interface: No such device
[root@localhost ~]#
Bizarre ! bizarre !
Es-tu sûr d'avoir fait, en root #yum install kmod-staging* ?

Pour vérifier, fais,
#yum list kmod-staging

S'il n'est pas installé, installe le et refait les commandes. #modprobe r8192_pci NE DOIT PAS retourner FATAL ... SInon, inutile d'aller plus loin.
Oups petite boulette de ma part :
lsmod|grep r81
r8192se_pci           438978  0
C'est "modprobe r8192se_pci" .


Toute mes excuses :hammer: Je devrais pas faire plusieurs choses en même temps!!

Mais a mon avis le kmod-staging n'est pas installé car le lsmod ne renvoie rien de cohérent.
remixbx wrote:Oups petite boulette de ma part :
lsmod|grep r81
r8192se_pci           438978  0
C'est "modprobe r8192se_pci" .

Toute mes excuses :hammer:
Non, non, tu as tout à fait raison !
-> L'installation par le drivers proprio (téléchargé sur le site puis compilé) fournit r8192se_pci : celui que tu as
-> Si on essaye de passer par kmod-staging (pour ne pas avoir à refaire la configuration à chque changement de noyau), on obtient r8192_pci. Par contre, d'après ce que tu sembles dire, ca ne fonctionne pas (on essaie quand même au cas où par chance 😉 ) et c'est peut-être confirmé par le fait que l'ID exact de la carte n'est pas supportée, d'après la DOC, par ce driver...

J'espère être claire (ca commence à peine à vraiment s'éclairer pour moi 😉 )

Pour le tuto, je pense que fox765 pourra plus ou moins suivre celui ci : http://www.linwik.com/wiki/using+the+realtek+8172+and+8192se+wireless+controller+with+ubuntu+9.10 ; en changeant simplement la première ligne pour installer les outils de compilation de fedora.
Chez moi:
 lspci |grep Network
07:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8171 (rev 10)
Chez moi, elle est detectée comme une 8171, mais c'est bien une 8192se, peu être qu'il y a eu une évolution depuis le montage de mon laptop.
et que le modprobe fonctionnera.

Je me trompe toujours de commande entre "lsmod" et "modprobe -l":
modprobe -l |grep 819
kernel/drivers/media/video/bt819.ko
kernel/drivers/net/wireless/r8192se_pci.ko
extra/staging/r8192_pci.ko
extra/staging/r8192u_usb.ko
extra/staging/r8192s_usb.ko
Si ca passe pas et qu'il n'arrive pas à compiler avec le tuto d'ubuntu, je reprendrais mon tuto de Backtrack et je l'adapterais pour Fedora.
Ya juste quelques lignes qui change entre une debian et Fedo, je devrais avoir un peu de temps ce week end.
Pour vérifier, fais,
#yum list kmod-staging
OK-----
[liveuser@localhost ~]$ su -
[root@localhost ~]# yum list kmod-staging
Loaded plugins: presto, refresh-packagekit
fedora/metalink                                          |  27 kB     00:00     
fedora                                                   | 4.3 kB     00:00     
fedora/primary_db                                        |  10 MB     00:26     
rpmfusion-free                                           | 2.8 kB     00:00     
rpmfusion-free/primary_db                                | 304 kB     00:01     
rpmfusion-free-updates                                   | 2.8 kB     00:00     
rpmfusion-free-updates/primary_db                        |  50 kB     00:00     
rpmfusion-nonfree                                        | 2.8 kB     00:00     
rpmfusion-nonfree/primary_db                             |  97 kB     00:00     
rpmfusion-nonfree-updates                                | 2.8 kB     00:00     
rpmfusion-nonfree-updates/primary_db                     | 6.5 kB     00:00     
updates/metalink                                         |  23 kB     00:00     
updates                                                  | 4.5 kB     00:00     
updates/primary_db                                       | 1.4 MB     00:03     
Installed Packages
kmod-staging.i686           2.6.33.2-2.fc13.5            @rpmfusion-free-updates
[root@localhost ~]#
Est-ce installé ou pas ?
^^ Ah oui, clairement : "Installed Packages : kmod-staging.i686"

Et #modprobe -l | grep 819
ne donne toujours pas r8192_pci (comme c'est le cas chez fox765)

- Si non ? je comprends pas... c'ets peut-re une histoire d'être en 32bits ou 64... ??
- Si oui : reprendre :

#modprobe r8192_pci
#lsmod | grep r8192 (pour vérifier qu'il est chargé. s'il ne l'est pas, inutile d'aller plus loin et faire plutôt : #modprobe -l | grep 819)
#service NetworkManger restart
#iwconfig
#ifconfig wlan0 up
J'ai refait l'install à tout hasard
[liveuser@localhost ~]$ su -
[root@localhost ~]# yum install kmod-staging*
Loaded plugins: presto, refresh-packagekit
Setting up Install Process
Package kmod-staging-2.6.33.2-2.fc13.5.i686 already installed and latest version
Package kmod-staging-2.6.33.5-112.fc13.i686-2.6.33.2-2.fc13.5.i686 already installed and latest version
Resolving Dependencies
--> Running transaction check
---> Package kmod-staging-2.6.33.3-85.fc13.i686.i686 0:2.6.33.2-2.fc13.3 set to be updated
---> Package kmod-staging-2.6.33.3-85.fc13.i686.PAE.i686 0:2.6.33.2-2.fc13.3 set to be updated
--> Processing Dependency: kernel-uname-r = 2.6.33.3-85.fc13.i686.PAE for package: kmod-staging-2.6.33.3-85.fc13.i686.PAE-2.6.33.2-2.fc13.3.i686
---> Package kmod-staging-2.6.33.4-95.fc13.i686.i686 0:2.6.33.2-2.fc13.4 set to be updated
--> Processing Dependency: kernel-uname-r = 2.6.33.4-95.fc13.i686 for package: kmod-staging-2.6.33.4-95.fc13.i686-2.6.33.2-2.fc13.4.i686
---> Package kmod-staging-2.6.33.4-95.fc13.i686.PAE.i686 0:2.6.33.2-2.fc13.4 set to be updated
--> Processing Dependency: kernel-uname-r = 2.6.33.4-95.fc13.i686.PAE for package: kmod-staging-2.6.33.4-95.fc13.i686.PAE-2.6.33.2-2.fc13.4.i686
---> Package kmod-staging-2.6.33.5-112.fc13.i686.PAE.i686 0:2.6.33.2-2.fc13.5 set to be updated
--> Processing Dependency: kernel-uname-r = 2.6.33.5-112.fc13.i686.PAE for package: kmod-staging-2.6.33.5-112.fc13.i686.PAE-2.6.33.2-2.fc13.5.i686
---> Package kmod-staging-PAE.i686 0:2.6.33.2-2.fc13.5 set to be updated
--> Running transaction check
---> Package kernel-PAE.i686 0:2.6.33.3-85.fc13 set to be installed
---> Package kernel-PAE.i686 0:2.6.33.5-112.fc13 set to be installed
---> Package kmod-staging-2.6.33.4-95.fc13.i686.i686 0:2.6.33.2-2.fc13.4 set to be updated
--> Processing Dependency: kernel-uname-r = 2.6.33.4-95.fc13.i686 for package: kmod-staging-2.6.33.4-95.fc13.i686-2.6.33.2-2.fc13.4.i686
---> Package kmod-staging-2.6.33.4-95.fc13.i686.PAE.i686 0:2.6.33.2-2.fc13.4 set to be updated
--> Processing Dependency: kernel-uname-r = 2.6.33.4-95.fc13.i686.PAE for package: kmod-staging-2.6.33.4-95.fc13.i686.PAE-2.6.33.2-2.fc13.4.i686
--> Finished Dependency Resolution
Error: Package: kmod-staging-2.6.33.4-95.fc13.i686.PAE-2.6.33.2-2.fc13.4.i686 (rpmfusion-free-updates)
           Requires: kernel-uname-r = 2.6.33.4-95.fc13.i686.PAE
           Installed: kernel-2.6.33.3-85.fc13.i686 (@released/$releasever)
           Installed: kernel-2.6.33.5-112.fc13.i686 (@updates)
           Installing: kernel-PAE-2.6.33.3-85.fc13.i686 (fedora)
           Installing: kernel-PAE-2.6.33.5-112.fc13.i686 (updates)
           Available: kernel-PAEdebug-2.6.33.3-85.fc13.i686 (fedora)
           Available: kernel-PAEdebug-2.6.33.5-112.fc13.i686 (updates)
           Available: kernel-debug-2.6.33.3-85.fc13.i686 (fedora)
           Available: kernel-debug-2.6.33.5-112.fc13.i686 (updates)
Error: Package: kmod-staging-2.6.33.4-95.fc13.i686.PAE-2.6.33.2-2.fc13.4.i686 (rpmfusion-free-updates)
           Requires: kernel-uname-r = 2.6.33.4-95.fc13.i686.PAE
           Installed: kernel-2.6.33.3-85.fc13.i686 (@released/$releasever)
           Installed: kernel-2.6.33.5-112.fc13.i686 (@updates)
           Installing: kernel-PAE-2.6.33.3-85.fc13.i686 (fedora)
           Available: kernel-PAE-2.6.33.5-112.fc13.i686 (updates)
           Available: kernel-PAEdebug-2.6.33.3-85.fc13.i686 (fedora)
           Available: kernel-PAEdebug-2.6.33.5-112.fc13.i686 (updates)
           Available: kernel-debug-2.6.33.3-85.fc13.i686 (fedora)
           Available: kernel-debug-2.6.33.5-112.fc13.i686 (updates)
Error: Package: kmod-staging-2.6.33.4-95.fc13.i686-2.6.33.2-2.fc13.4.i686 (rpmfusion-free-updates)
           Requires: kernel-uname-r = 2.6.33.4-95.fc13.i686
           Installed: kernel-2.6.33.3-85.fc13.i686 (@released/$releasever)
           Installed: kernel-2.6.33.5-112.fc13.i686 (@updates)
           Installing: kernel-PAE-2.6.33.3-85.fc13.i686 (fedora)
           Available: kernel-PAE-2.6.33.5-112.fc13.i686 (updates)
           Available: kernel-PAEdebug-2.6.33.3-85.fc13.i686 (fedora)
           Available: kernel-PAEdebug-2.6.33.5-112.fc13.i686 (updates)
           Available: kernel-debug-2.6.33.3-85.fc13.i686 (fedora)
           Available: kernel-debug-2.6.33.5-112.fc13.i686 (updates)
Error: Package: kmod-staging-2.6.33.4-95.fc13.i686-2.6.33.2-2.fc13.4.i686 (rpmfusion-free-updates)
           Requires: kernel-uname-r = 2.6.33.4-95.fc13.i686
           Installed: kernel-2.6.33.3-85.fc13.i686 (@released/$releasever)
           Installed: kernel-2.6.33.5-112.fc13.i686 (@updates)
           Installing: kernel-PAE-2.6.33.3-85.fc13.i686 (fedora)
           Installing: kernel-PAE-2.6.33.5-112.fc13.i686 (updates)
           Available: kernel-PAEdebug-2.6.33.3-85.fc13.i686 (fedora)
           Available: kernel-PAEdebug-2.6.33.5-112.fc13.i686 (updates)
           Available: kernel-debug-2.6.33.3-85.fc13.i686 (fedora)
           Available: kernel-debug-2.6.33.5-112.fc13.i686 (updates)
 You could try using --skip-broken to work around the problem
 You could try running: rpm -Va --nofiles --nodigest
[root@localhost ~]#
Bon ou pas bon ????
fox765 wrote:J'ai refait l'install à tout hasard

Bon ou pas bon ????
C'était déjà bon. Regarde plutôt mon post précédent pour la suite des évènements
Si oui : reprendre :

#modprobe r8192_pci
#lsmod | grep r8192 (pour vérifier qu'il est chargé. s'il ne l'est pas, inutile d'aller plus loin et faire plutôt : #modprobe -l | grep 819)
#service NetworkManger restart
#iwconfig
#ifconfig wlan0 up
les retours:
[liveuser@localhost ~]$ su -
[root@localhost ~]# modprobe r8192_pci
FATAL: Module r8192_pci not found.
[root@localhost ~]# lsmod | grep r8192
[root@localhost ~]# modprobe -l | grep 8192
[root@localhost ~]# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

[root@localhost ~]# ifconfig wlan0 up
wlan0: unknown interface: No such device
[root@localhost ~]#
Bon, je ne comprends donc pas ! J'ai fait l'installtion de kmod-staging pour vérifier, et j'avais bien le module r8192_pci dispo.

Bon, c'est pas grave, on va donc tenter (comme tu le souhaitais à l'orignie en fait) l'installation en compilant le module...
Donc par étapes, en root :
# yum install gcc gcc-c++ kernel-devel kernel-headers patch make
(outils pour la compilation sous fedora). J'espère que ca suffit, sinon on en rajoutera au fur et à mesure.

On va utiliser ton archive rtl8192se_linux_etc.tar.gz

Imaginons qu'elle soit dans le répertoire /home/TONPSEUDO . Poste alors les résultats des commandes suivantes (attention, si il y a une erreur, renvoie là avant d'avancer).
# cd /usr/src
# tar xzvf /home/TONPSEUDO/rtl8192se_linux_2.6.0015.0127.2010.tar.gz
# cd rtl8192se_linux_2.6.0015.0127.2010
# cp -rf firmware/RTL8192SE /lib/firmware
# make
Et enfin, si make ne se termine pas par un erreur :
#find / -name r8192se_pci -print
Bonjour

je reprends après absence

le retour, il semblerait que les paquets se soient bien installés
[liveuser@localhost ~]$ su -
[root@localhost ~]# yum install gcc gcc-c++ kernel-devel kernel-headers patch make
Loaded plugins: presto, refresh-packagekit
fedora/metalink                                          |  28 kB     00:00     
fedora                                                   | 4.3 kB     00:00     
fedora/primary_db                                        |  10 MB     00:19     
rpmfusion-free                                           | 2.8 kB     00:00     
rpmfusion-free/primary_db                                | 304 kB     00:00     
rpmfusion-free-updates                                   | 2.8 kB     00:00     
rpmfusion-free-updates/primary_db                        |  50 kB     00:00     
rpmfusion-nonfree                                        | 2.8 kB     00:00     
rpmfusion-nonfree/primary_db                             |  97 kB     00:00     
rpmfusion-nonfree-updates                                | 2.8 kB     00:00     
rpmfusion-nonfree-updates/primary_db                     | 6.5 kB     00:00     
updates/metalink                                         |  23 kB     00:00     
updates                                                  | 4.5 kB     00:00     
updates/primary_db                                       | 1.4 MB     00:02     
Setting up Install Process
Package 1:make-3.81-18.fc12.i686 already installed and latest version
Resolving Dependencies
--> Running transaction check
---> Package gcc.i686 0:4.4.4-2.fc13 set to be updated
--> Processing Dependency: cpp = 4.4.4-2.fc13 for package: gcc-4.4.4-2.fc13.i686
--> Processing Dependency: cloog-ppl >= 0.15 for package: gcc-4.4.4-2.fc13.i686
--> Processing Dependency: glibc-devel >= 2.2.90-12 for package: gcc-4.4.4-2.fc13.i686
---> Package gcc-c++.i686 0:4.4.4-2.fc13 set to be updated
--> Processing Dependency: libstdc++-devel = 4.4.4-2.fc13 for package: gcc-c++-4.4.4-2.fc13.i686
---> Package kernel-devel.i686 0:2.6.33.5-112.fc13 set to be installed
---> Package kernel-headers.i686 0:2.6.33.5-112.fc13 set to be updated
---> Package patch.i686 0:2.6.1-1.fc13 set to be updated
--> Running transaction check
---> Package cloog-ppl.i686 0:0.15.7-1.fc12 set to be updated
--> Processing Dependency: libppl.so.7 for package: cloog-ppl-0.15.7-1.fc12.i686
--> Processing Dependency: libppl_c.so.2 for package: cloog-ppl-0.15.7-1.fc12.i686
---> Package cpp.i686 0:4.4.4-2.fc13 set to be updated
---> Package glibc-devel.i686 0:2.12-1 set to be updated
--> Processing Dependency: glibc-headers = 2.12-1 for package: glibc-devel-2.12-1.i686
--> Processing Dependency: glibc-headers for package: glibc-devel-2.12-1.i686
---> Package libstdc++-devel.i686 0:4.4.4-2.fc13 set to be updated
--> Running transaction check
---> Package glibc-headers.i686 0:2.12-1 set to be updated
---> Package ppl.i686 0:0.10.2-10.fc12 set to be updated
--> Finished Dependency Resolution

Dependencies Resolved

================================================================================
 Package               Arch       Version                   Repository     Size
================================================================================
Installing:
 gcc                   i686       4.4.4-2.fc13              fedora        8.1 M
 gcc-c++               i686       4.4.4-2.fc13              fedora        4.3 M
 kernel-devel          i686       2.6.33.5-112.fc13         updates       6.3 M
 kernel-headers        i686       2.6.33.5-112.fc13         updates       763 k
 patch                 i686       2.6.1-1.fc13              fedora         85 k
Installing for dependencies:
 cloog-ppl             i686       0.15.7-1.fc12             fedora         81 k
 cpp                   i686       4.4.4-2.fc13              fedora        3.3 M
 glibc-devel           i686       2.12-1                    fedora        959 k
 glibc-headers         i686       2.12-1                    fedora        596 k
 libstdc++-devel       i686       4.4.4-2.fc13              fedora        1.5 M
 ppl                   i686       0.10.2-10.fc12            fedora        1.1 M

Transaction Summary
================================================================================
Install      11 Package(s)
Upgrade       0 Package(s)

Total download size: 27 M
Installed size: 74 M
Is this ok [y/N]: y
Downloading Packages:
Setting up and reading Presto delta metadata
fedora/prestodelta                                       |  414 B     00:00     
updates/prestodelta                                      | 5.3 kB     00:00     
Processing delta metadata
Package(s) data still to download: 27 M
(1/11): cloog-ppl-0.15.7-1.fc12.i686.rpm                 |  81 kB     00:00     
(2/11): cpp-4.4.4-2.fc13.i686.rpm                        | 3.3 MB     00:06     
(3/11): gcc-4.4.4-2.fc13.i686.rpm                        | 8.1 MB     00:14     
(4/11): gcc-c++-4.4.4-2.fc13.i686.rpm                    | 4.3 MB     00:07     
(5/11): glibc-devel-2.12-1.i686.rpm                      | 959 kB     00:01     
(6/11): glibc-headers-2.12-1.i686.rpm                    | 596 kB     00:01     
(7/11): kernel-devel-2.6.33.5-112.fc13.i686.rpm          | 6.3 MB     00:11     
(8/11): kernel-headers-2.6.33.5-112.fc13.i686.rpm        | 763 kB     00:01     
(9/11): libstdc++-devel-4.4.4-2.fc13.i686.rpm            | 1.5 MB     00:02     
(10/11): patch-2.6.1-1.fc13.i686.rpm                     |  85 kB     00:00     
(11/11): ppl-0.10.2-10.fc12.i686.rpm                     | 1.1 MB     00:02     
--------------------------------------------------------------------------------
Total                                           526 kB/s |  27 MB     00:52     
Running rpm_check_debug
Running Transaction Test
Transaction Test Succeeded
Running Transaction
  Installing     : ppl-0.10.2-10.fc12.i686                                 1/11 
  Installing     : cloog-ppl-0.15.7-1.fc12.i686                            2/11 
  Installing     : cpp-4.4.4-2.fc13.i686                                   3/11 
  Installing     : kernel-headers-2.6.33.5-112.fc13.i686                   4/11 
  Installing     : glibc-headers-2.12-1.i686                               5/11 
  Installing     : glibc-devel-2.12-1.i686                                 6/11 
  Installing     : libstdc++-devel-4.4.4-2.fc13.i686                       7/11 
  Installing     : kernel-devel-2.6.33.5-112.fc13.i686                     8/11 
  Installing     : gcc-4.4.4-2.fc13.i686                                   9/11 
  Installing     : gcc-c++-4.4.4-2.fc13.i686                              10/11 
  Installing     : patch-2.6.1-1.fc13.i686                                11/11 

Installed:
  gcc.i686 0:4.4.4-2.fc13               gcc-c++.i686 0:4.4.4-2.fc13            
  kernel-devel.i686 0:2.6.33.5-112.fc13 kernel-headers.i686 0:2.6.33.5-112.fc13
  patch.i686 0:2.6.1-1.fc13            

Dependency Installed:
  cloog-ppl.i686 0:0.15.7-1.fc12             cpp.i686 0:4.4.4-2.fc13           
  glibc-devel.i686 0:2.12-1                  glibc-headers.i686 0:2.12-1       
  libstdc++-devel.i686 0:4.4.4-2.fc13        ppl.i686 0:0.10.2-10.fc12         

Complete!
[root@localhost ~]#
Maintenant que dois-je faire pour aller chercher mon driver que j'ai copié sur bureau , Peux-tu me donner le chemin car sans toi, je suis perdu pour ce cheminement



J'en profite pour te signaler que je dois m'absenter dans qq instants pour toute la journée
Du coup, faudrait faire :
# cd /usr/src
# tar xzvf /home/liveuser/Bureau/rtl8192se_linux_2.6.0015.0127.2010.tar.gz
# cd rtl8192se_linux_2.6.0015.0127.2010
# cp -rf firmware/RTL8192SE /lib/firmware
# make
Et enfin, si make ne se termine pas par un erreur :
#find / -name r8192se_pci -print
Bonjour balustre

malheureusement je crois comprendre que le driver n'a pu être trouvé
[liveuser@localhost ~]$ su -
[root@localhost ~]# cd /usr/src
[root@localhost src]# tar xzvf /home/liveuser/Bureau/rtl8192se_linux_2.6.0015.0127.2010.tar.gz
tar: /home/liveuser/Bureau/rtl8192se_linux_2.6.0015.0127.2010.tar.gz: Cannot open: No such file or directory
tar: Error is not recoverable: exiting now
tar: Child returned status 2
tar: Exiting with failure status due to previous errors
[root@localhost src]# cd rtl8192se_linux_2.6.0015.0127.2010
-bash: cd: rtl8192se_linux_2.6.0015.0127.2010: No such file or directory
[root@localhost src]# cp -rf firmware/RTL8192SE /lib/firmware
cp: cannot stat `firmware/RTL8192SE': No such file or directory
[root@localhost src]# make
make: *** No targets specified and no makefile found.  Stop.
[root@localhost src]# find / -name r8192se_pci -print
[root@localhost src]#
Pourquoi donc est-ce si compliqué d'ouvrir un pilote sous fedora ?