Redémarrage à froid ce soir et plus aucun problème.
Ce devait être effectivement un mauvais contact électrique interne...
Par contre j'ai peur que le disque ait souffert avec toutes ces coupures.
J'ai effectué un smarctl -t short et voilà le résultat. Il faut procéder à un e2fck sur ce disque ? (je ne comprends rien au rapport ci-dessous)
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.11-200.fc35.x86_64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Black
Device Model: WDC WD5003AZEX-00K1GA0
Serial Number: WD-WCC1S6926919
LU WWN Device Id: 5 0014ee 2b3fbb695
Firmware Version: 80.00A80
User Capacity: 500107862016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Mar 2 21:59:51 2022 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 5820) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 69) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x30b5) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 176 172 021 Pre-fail Always - 2175
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 874
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1552
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 874
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 99
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 774
194 Temperature_Celsius 0x0022 111 101 000 Old_age Always - 32
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 15460 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 15460 occurred at disk power-on lifetime: 726 hours (30 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 08 00:11:40.922 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:11:40.921 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:11:40.921 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 00:11:40.921 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:11:40.920 IDENTIFY DEVICE
Error 15459 occurred at disk power-on lifetime: 726 hours (30 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 08 00:11:40.921 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 00:11:40.921 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:11:40.920 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 08 00:11:40.910 SET FEATURES [Enable SATA feature]
Error 15458 occurred at disk power-on lifetime: 726 hours (30 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 08 00:11:40.921 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:11:40.920 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 08 00:11:40.910 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:11:40.909 IDENTIFY DEVICE
Error 15457 occurred at disk power-on lifetime: 726 hours (30 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 08 00:11:40.910 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:11:40.909 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:11:40.909 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 00:11:40.909 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:11:40.908 IDENTIFY DEVICE
Error 15456 occurred at disk power-on lifetime: 726 hours (30 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 08 00:11:40.909 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 00:11:40.909 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:11:40.908 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 08 00:11:40.897 SET FEATURES [Enable SATA feature]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1552 -
# 2 Short offline Completed without error 00% 822 -
# 3 Short offline Completed without error 00% 720 -
# 4 Short offline Completed without error 00% 720 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
La commande "sensor" me donne les infos ci-dessous (il fait bien plus de 13°C chez nous [heureusement]) :
atk0110-acpi-0
Adapter: ACPI interface
Vcore Voltage: 1.04 V (min = +0.80 V, max = +1.60 V)
+3.3V Voltage: 3.29 V (min = +2.97 V, max = +3.63 V)
+5V Voltage: 5.02 V (min = +4.50 V, max = +5.50 V)
+12V Voltage: 12.22 V (min = +10.20 V, max = +13.80 V)
CPU Fan Speed: 917 RPM (min = 600 RPM, max = 7200 RPM)
Chassis Fan Speed: 838 RPM (min = 600 RPM, max = 7200 RPM)
Chassis2 Fan Speed: 0 RPM (min = 600 RPM, max = 7200 RPM)
Power Fan Speed: 0 RPM (min = 600 RPM, max = 7200 RPM)
CPU Temperature: +29.0°C (high = +60.0°C, crit = +95.0°C)
MB Temperature: +27.0°C (high = +45.0°C, crit = +75.0°C)
nouveau-pci-0100
Adapter: PCI adapter
GPU core: 900.00 mV (min = +0.90 V, max = +1.11 V)
temp1: +35.0°C (high = +95.0°C, hyst = +3.0°C)
(crit = +105.0°C, hyst = +5.0°C)
(emerg = +135.0°C, hyst = +5.0°C)
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +13.4°C (high = +70.0°C)
(crit = +90.0°C, hyst = +88.0°C)
La commande inxi -F
System:
Host: fedora.home Kernel: 5.16.11-200.fc35.x86_64 x86_64 bits: 64
Desktop: Cinnamon 5.2.7 Distro: Fedora release 35 (Thirty Five)
Machine:
Type: Desktop Mobo: ASUSTeK model: M4A89GTD-PRO v: Rev 1.xx
serial: <superuser required> BIOS: American Megatrends v: 1702
date: 10/22/2010
CPU:
Info: quad core model: AMD Phenom II X4 840 bits: 64 type: MCP cache:
L2: 2 MiB
Speed (MHz): avg: 800 min/max: 800/3200 cores: 1: 800 2: 800 3: 800
4: 800
Graphics:
Device-1: NVIDIA GF119 [GeForce GT 610] driver: nouveau v: kernel
Display: x11 server: X.Org 1.20.14 driver: loaded: modesetting
unloaded: fbdev,vesa resolution: 1920x1080~60Hz
OpenGL: renderer: NVD9 v: 4.3 Mesa 21.3.6
Audio:
Device-1: AMD SBx00 Azalia driver: snd_hda_intel
Device-2: NVIDIA GF119 HDMI Audio driver: snd_hda_intel
Sound Server-1: ALSA v: k5.16.11-200.fc35.x86_64 running: yes
Sound Server-2: PipeWire v: 0.3.47 running: yes
Network:
Device-1: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet
driver: r8169
IF: enp4s0 state: up speed: 100 Mbps duplex: full mac: bc:ae:c5:23:ac:69
Drives:
Local Storage: total: 465.76 GiB used: 79.2 GiB (17.0%)
ID-1: /dev/sda vendor: Western Digital model: WD5003AZEX-00K1GA0
size: 465.76 GiB
Partition:
ID-1: / size: 464.76 GiB used: 78.94 GiB (17.0%) fs: btrfs dev: /dev/sda2
ID-2: /boot size: 973.4 MiB used: 267.6 MiB (27.5%) fs: ext4
dev: /dev/sda1
ID-3: /home size: 464.76 GiB used: 78.94 GiB (17.0%) fs: btrfs
dev: /dev/sda2
Swap:
ID-1: swap-1 type: zram size: 8 GiB used: 0 KiB (0.0%) dev: /dev/zram0
Sensors:
System Temperatures: cpu: 27.0 C mobo: 25.0 C gpu: nouveau temp: 29.0 C
Fan Speeds (RPM): cpu: 910 psu: 0 case-1: 822 case-2: 0
Info:
Processes: 259 Uptime: 2m Memory: 11.68 GiB used: 1.5 GiB (12.8%)
Shell: Bash inxi: 3.3.12
Merci à tous.