J'ai mon vieux 500Go WD Black qui tiens encore le coup sur mon serveur 🙂. Manque un peu en perf, mais tourne toujours comme une horloge :
# smartctl -a /dev/sda
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.13-300.fc29.x86_64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Black
Device Model: WDC WD5001AALS-00L3B2
Serial Number: WD-Wqsddsqdqsqdsqdsqds
LU WWN Device Id: qdsdqsdqssqdqdsqds
Firmware Version: 01.03B01
User Capacity: 500107862016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.5, 3.0 Gb/s
Local Time is: Tue Jan 15 20:54:07 2019 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (11160) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 131) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 161 152 021 Pre-fail Always - 4908
4 Start_Stop_Count 0x0032 094 094 000 Old_age Always - 6119
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 058 058 000 Old_age Always - 31308
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 094 094 000 Old_age Always - 6070
192 Power-Off_Retract_Count 0x0032 196 196 000 Old_age Always - 3512
193 Load_Cycle_Count 0x0032 198 198 000 Old_age Always - 6106
194 Temperature_Celsius 0x0022 109 094 000 Old_age Always - 38
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 937
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 17246 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Et il en a vue des vertes et des pas mures, après même un arrêt de plus de 3 ans... Dans le froid, dans le vent au fin fond de la nuit... Toujours debout à tournoyer fidèle au poste 🙂 et pourtant si vieux (doit pas être loin des 10 ans le bougre...).
Depuis je ne prend plus que des black dont certains on pas loin de 5 ans... J'ai fais qu'un seul écart à une époque avec un seagate 7200.14 qui n'a pas tenu la durée de la garantie (dans les 1 ans...) avant d'avoir des soucis :
# smartctl -a /dev/sdc
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.13-300.fc29.x86_64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST2000DM001-1CH164
Serial Number: wxccxwxcwxwcxcwxcw
LU WWN Device Id: wxccxwxcwxwcxwccxwcxw
Firmware Version: CC27
User Capacity: 2000398934016 bytes [2,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Tue Jan 15 21:02:02 2019 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 584) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 214) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3085) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 118 095 006 Pre-fail Always - 170694784
3 Spin_Up_Time 0x0003 096 095 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 098 098 020 Old_age Always - 2730
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 079 060 030 Pre-fail Always - 98577062
9 Power_On_Hours 0x0032 090 090 000 Old_age Always - 9201
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 020 Old_age Always - 2698
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 404
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 0 0 2
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 068 053 045 Old_age Always - 32 (Min/Max 27/35)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 518
193 Load_Cycle_Count 0x0032 074 074 000 Old_age Always - 52727
194 Temperature_Celsius 0x0022 032 047 000 Old_age Always - 32 (0 7 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 1
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 4897h+55m+43.202s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 31227401529
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 33199161546
SMART Error Log Version: 1
ATA Error Count: 404 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 404 occurred at disk power-on lifetime: 4898 hours (204 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 78 36 7e 00 Error: UNC at LBA = 0x007e3678 = 8271480
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 78 36 7e 40 00 00:06:17.330 READ FPDMA QUEUED
ea 00 00 00 00 00 a0 00 00:06:17.322 FLUSH CACHE EXT
60 00 80 ff ff ff 4f 00 00:06:17.322 READ FPDMA QUEUED
ea 00 00 00 00 00 a0 00 00:06:17.294 FLUSH CACHE EXT
61 00 10 ff ff ff 4f 00 00:06:17.294 WRITE FPDMA QUEUED
Error 403 occurred at disk power-on lifetime: 4898 hours (204 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 78 36 7e 00 Error: UNC at LBA = 0x007e3678 = 8271480
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 78 36 7e 40 00 00:06:13.647 READ FPDMA QUEUED
ea 00 00 00 00 00 a0 00 00:06:13.647 FLUSH CACHE EXT
ef 10 02 00 00 00 a0 00 00:06:13.647 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:06:13.647 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:06:13.646 IDENTIFY DEVICE
Error 402 occurred at disk power-on lifetime: 4898 hours (204 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 78 36 7e 00 Error: UNC at LBA = 0x007e3678 = 8271480
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 78 36 7e 40 00 00:06:09.987 READ FPDMA QUEUED
ea 00 00 00 00 00 a0 00 00:06:09.965 FLUSH CACHE EXT
61 00 08 ff ff ff 4f 00 00:06:09.965 WRITE FPDMA QUEUED
ea 00 00 00 00 00 a0 00 00:06:09.881 FLUSH CACHE EXT
61 00 08 ff ff ff 4f 00 00:06:09.880 WRITE FPDMA QUEUED
Error 401 occurred at disk power-on lifetime: 4898 hours (204 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 78 36 7e 00 Error: UNC at LBA = 0x007e3678 = 8271480
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 78 36 7e 40 00 00:06:05.752 READ FPDMA QUEUED
ea 00 00 00 00 00 a0 00 00:06:05.752 FLUSH CACHE EXT
ea 00 00 00 00 00 a0 00 00:06:05.752 FLUSH CACHE EXT
ea 00 00 00 00 00 a0 00 00:06:05.752 FLUSH CACHE EXT
ea 00 00 00 00 00 a0 00 00:06:05.752 FLUSH CACHE EXT
Error 400 occurred at disk power-on lifetime: 4898 hours (204 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 78 36 7e 00 Error: UNC at LBA = 0x007e3678 = 8271480
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 78 36 7e 40 00 00:06:02.068 READ FPDMA QUEUED
61 00 08 ff ff ff 4f 00 00:06:02.068 WRITE FPDMA QUEUED
61 00 08 ff ff ff 4f 00 00:06:02.068 WRITE FPDMA QUEUED
61 00 08 ff ff ff 4f 00 00:06:02.068 WRITE FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:06:02.051 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Suffit de l'entendre gratouiller par moment pour s'en rendre compte... (et là il gratouille plus que des puces sur le dos d'un chien... Pour en revenir à une blagounette sur un autre sujet :-P).