Fedora-Fr - Communauté francophone Fedora - Linux

Communauté francophone des utilisateurs de la distribution Linux Fedora.

  

Dernière news : Représenter Fedora au Capitole du Libre 2019

#1 02/05/2018 13:52:54

antbel
Membre
Inscription : 03/12/2007
Messages : 727

[Résolu] F28 installation fraiche erreur ACPI : chronyd ne se lance pas

Bonjour,

Machine : COMPAQ Presario CQ57 BIOS à jour : Processeur : AMD E-450 APU with Radeon(tm) HD Graphics × 2 Memoire 8Go Video : Radeon HD 6320
Noyau Linux 4.16.5-300.fc28.x86_64 x86_64 , pas de EFI

Résultat de : dmesg | grep ACPI

$ dmesg | grep ACPI
[    0.000000] BIOS-e820: [mem 0x00000000dfebf000-0x00000000dfef4fff] ACPI data
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000FE020 000024 (v02 HPQOEM)
[    0.000000] ACPI: XSDT 0x00000000DFEF4120 00006C (v01 HPQOEM SLIC-MPC 00000001      01000013)
[    0.000000] ACPI: FACP 0x00000000DFEF3000 0000F4 (v04 HPQOEM SLIC-MPC 00000001 ACPI 00040000)
[    0.000000] ACPI: DSDT 0x00000000DFEDE000 01009F (v01 HP     INSYDE   F0000000 ACPI 00040000)
[    0.000000] ACPI: FACS 0x00000000DFC96000 000040
[    0.000000] ACPI: FACS 0x00000000DFC96000 000040
[    0.000000] ACPI: HPET 0x00000000DFEF2000 000038 (v01 HP     INSYDE   00000001 ACPI 00040000)
[    0.000000] ACPI: APIC 0x00000000DFEF1000 000084 (v02 HP     INSYDE   00000001 ACPI 00040000)
[    0.000000] ACPI: MCFG 0x00000000DFEF0000 00003C (v01 HP     INSYDE   00000001 ACPI 00040000)
[    0.000000] ACPI: ASF! 0x00000000DFEEF000 0000A5 (v32 HP     INSYDE   00000001 ACPI 00040000)
[    0.000000] ACPI: BOOT 0x00000000DFEDD000 000028 (v01 HP     INSYDE   00000001 ACPI 00040000)
[    0.000000] ACPI: SLIC 0x00000000DFEDC000 000176 (v01 HPQOEM SLIC-MPC 00000001 ACPI 00040000)
[    0.000000] ACPI: SSDT 0x00000000DFEDB000 0003DE (v01 HP     INSYDE   00000001 AMD  00000001)
[    0.000000] ACPI: SSDT 0x00000000DFED9000 00168E (v02 HP     INSYDE   00000001 MSFT 04000000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x43538210 base: 0xfed00000
[    0.000000] ACPI: Core revision 20180105
[    0.000000] ACPI: 3 ACPI AML tables successfully acquired and loaded
[    0.031010] PM: Registering ACPI NVS region [mem 0xdfbbf000-0xdfebefff] (3145728 bytes)
[    0.036330] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.036330] ACPI: bus type PCI registered
[    0.037015] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.042312] ACPI: Added _OSI(Module Device)
[    0.042312] ACPI: Added _OSI(Processor Device)
[    0.042312] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.042312] ACPI: Added _OSI(Processor Aggregator Device)
[    0.043161] ACPI: Executed 1 blocks of module-level executable AML code
[    0.051760] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[    0.052738] ACPI: EC: EC started
[    0.052740] ACPI: EC: interrupt blocked
[    0.079345] ACPI: \_SB_.PCI0.LPC0.EC0_: Used as first EC
[    0.079351] ACPI: \_SB_.PCI0.LPC0.EC0_: GPE=0x3, EC_CMD/EC_SC=0x66, EC_DATA=0x62
[    0.079354] ACPI: \_SB_.PCI0.LPC0.EC0_: Used as boot DSDT EC to handle transactions
[    0.079356] ACPI: Interpreter enabled
[    0.079402] ACPI: (supports S0 S3 S4 S5)
[    0.079405] ACPI: Using IOAPIC for interrupt routing
[    0.079833] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.080302] ACPI: Enabled 4 GPEs in block 00 to 1F
[    0.109929] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.156733] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0
[    0.156924] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0
[    0.157182] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0
[    0.157386] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0
[    0.157601] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0
[    0.157814] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0
[    0.157992] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0
[    0.158221] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0
[    0.159002] ACPI: EC: interrupt unblocked
[    0.159002] ACPI: EC: event unblocked
[    0.159002] ACPI: \_SB_.PCI0.LPC0.EC0_: GPE=0x3, EC_CMD/EC_SC=0x66, EC_DATA=0x62
[    0.159002] ACPI: \_SB_.PCI0.LPC0.EC0_: Used as boot DSDT EC to handle transactions and events
[    0.160123] ACPI: bus type USB registered
[    0.161128] PCI: Using ACPI for IRQ routing
[    0.206302] pnp: PnP ACPI init
[    0.206672] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.207155] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.207328] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.207545] system 00:03: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.222623] pnp 00:04: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.222721] pnp 00:05: Plug and Play ACPI device, IDs SYN1e4b SYN1e00 SYN0002 PNP0f13 (active)
[    0.223797] pnp: PnP ACPI: found 6 devices
[    2.346215] ACPI: AC Adapter [AC] (on-line)
[    2.346377] ACPI: Lid Switch [LID]
[    2.346483] ACPI: Power Button [PWRB]
[    2.346611] ACPI: Power Button [PWRF]
[    2.354381] ACPI: Thermal Zone [TSZ0] (53 C)
[    2.395290] ACPI: Battery Slot [BAT0] (battery present)
[   11.587641] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[   13.414640] ACPI Error: Field [B128] at bit offset/length 128/1024 exceeds size of target Buffer (160 bits) (20180105/dsopcode-235)
[   13.414666] ACPI Error: Method parse/execution failed \_SB.WMID.HWCD, AE_AML_BUFFER_LIMIT (20180105/psparse-550)
[   13.414690] ACPI Error: Method parse/execution failed \_SB.WMID.WMAD, AE_AML_BUFFER_LIMIT (20180105/psparse-550)
[   13.669433] ACPI Error: Field [B128] at bit offset/length 128/1024 exceeds size of target Buffer (160 bits) (20180105/dsopcode-235)
[   13.669460] ACPI Error: Method parse/execution failed \_SB.WMID.HWCD, AE_AML_BUFFER_LIMIT (20180105/psparse-550)
[   13.669486] ACPI Error: Method parse/execution failed \_SB.WMID.WMAD, AE_AML_BUFFER_LIMIT (20180105/psparse-550)
[   18.882428] ACPI Error: Field [B128] at bit offset/length 128/1024 exceeds size of target Buffer (160 bits) (20180105/dsopcode-235)
[   18.882454] ACPI Error: Method parse/execution failed \_SB.WMID.HWCD, AE_AML_BUFFER_LIMIT (20180105/psparse-550)
[   18.882480] ACPI Error: Method parse/execution failed \_SB.WMID.WMAD, AE_AML_BUFFER_LIMIT (20180105/psparse-550)

De plus : avec dmesg | grep sp51

$ dmesg | grep sp51
[   11.983945] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver
[   11.995207] sp5100-tco sp5100-tco: I/O address 0x0cd6 already in use
[   11.995229] sp5100-tco: probe of sp5100-tco failed with error -16

Je constate que NTP et GSSAPI ne démarre pas et que le service chronyd est "failed"

$ systemctl status chronyd
● chronyd.service - NTP client/server
   Loaded: loaded (/usr/lib/systemd/system/chronyd.service; enabled; vendor preset: enabled)
   Active: failed (Result: timeout) since Wed 2018-05-02 12:44:16 CEST; 1h 0min ago
     Docs: man:chronyd(8)
           man:chrony.conf(5)
  Process: 620 ExecStart=/usr/sbin/chronyd $OPTIONS (code=killed, signal=TERM)

Warning: Journal has been rotated since unit was started. Log output is incomplete or unavailable.

Par contre après le login et en relançant #systemctl start chronyd
pas d'erreur , le service se lance

- J'ai essayé les différentes options au boot sur acpi : acpi=off , noacpi, acpi=Linux etc..... rien y fait avec of course # grub2-mkconfig -o /boot/grub2/grub.cfg
- j'ai essayé de blaclister dans /etc/modporbes.d/ sp5100_tco.conf aucun résultats
- Gogol ne m'a été d'aucun secours pour l'instant

Merci pour votre aide


Cicéron c'est Poincaré

Hors ligne

#2 02/05/2018 14:15:26

Refuznik
Membre
Inscription : 31/01/2007
Messages : 7 387

Re : [Résolu] F28 installation fraiche erreur ACPI : chronyd ne se lance pas

Oui, enfin les erreur d'acpi tu peux laisser courir.
Pour ton sp5100_tco https://debian-facile.org/viewtopic.php?id=18836

Pour chronyd ça c'est autre chose ; vérifie si selinux ne te bloque pas.

Hors ligne

#3 02/05/2018 15:29:37

antbel
Membre
Inscription : 03/12/2007
Messages : 727

Re : [Résolu] F28 installation fraiche erreur ACPI : chronyd ne se lance pas

Re:
Ce qui est gênant dans cette histoire c'est que le boot dure 3 minutes alors qu'avant cela durait 20secondes.
Laptop avec SSD.
Ensuite faut relancer chronyd
J'ai essayé sans succès de blacklister sp5100_tco puis i2c_piix4 selon le rapport bugzilla :
https://bugzilla.redhat.com/show_bug.cgi?id=1406844
Cette histoire traine depuis longtemps, il y a un conflit d'adresse mémoire pour :
- sp5100_tco
- i2c_piix4

Il semblerait qu'il y ait un patch kernel récent:
https://patchwork.kernel.org/patch/10132159/

Pouvez-vous m'aidez, je n'ai jamais patché un noyau ??

???? http://www.labbott.name/blog/2015/12/17 … ra-kernel/  ???

Dernière modification par antbel (02/05/2018 15:33:07)


Cicéron c'est Poincaré

Hors ligne

#4 02/05/2018 15:34:34

Mister_G
Membre
Lieu : Rouen (76)
Inscription : 07/05/2007
Messages : 654

Re : [Résolu] F28 installation fraiche erreur ACPI : chronyd ne se lance pas

que retourne

$systemd-analyze blame

i7 870 - 16 Go - gtx 970 - ssd 500 Go - Win 10 +  ssd 250 Go - F27 64 Fluxbox - 28" hanns g
lenovo i5- 4 Go - ssd 128 Go - debian sid 32 Fluxbox  - 15.6"

Hors ligne

#5 02/05/2018 15:50:19

antbel
Membre
Inscription : 03/12/2007
Messages : 727

Re : [Résolu] F28 installation fraiche erreur ACPI : chronyd ne se lance pas

En rajoutant le rpm watchdog cela résout le problème


Cicéron c'est Poincaré

Hors ligne

Pied de page des forums