Fedora-Fr - Communauté francophone Fedora - Linux

Communauté francophone des utilisateurs de la distribution Linux Fedora.

  

Dernière news : Rencontrez Borsalinux-fr aux RMLL à Strasbourg du 7 au 12 juillet

#1 13/04/2018 21:21:54

ottovonstein
Membre
Inscription : 10/03/2010
Messages : 118

[Résolu] ventilos devenu fous

Bonjour. J'ai ouvert une rom genesis hier au soir ( street of rage genesis avec gens, nostalgie... ) passé en mode plein écran tout est parti en cacahuette...
Impossible de sortir du mode plein ecran, obligé de hard reboot.... Gens c'est fini ! mais depuis mon ventilo tourne a fond 5 secondes fait une pause et repart pour 5 secondes en boucle. et ce des qu'il est alimenté, avant le splash screen du bios, pendant la séquence de boot et aussi pendant le reste de la session.
Je suis complètement pris de cours j'ai auune idée de part quelle bout prendre le probléme....

Je prend la moidre piste.

lspci
00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller (rev 06)
00:02.0 VGA compatible controller: Intel Corporation 4th Gen Core Processor Integrated Graphics Controller (rev 06)
00:03.0 Audio device: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller (rev 06)
00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05)
00:16.0 Communication controller: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 (rev 04)
00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 (rev 05)
00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 05)
00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 (rev d5)
00:1c.2 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #3 (rev d5)
00:1c.3 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #4 (rev d5)
00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 (rev 05)
00:1f.0 ISA bridge: Intel Corporation HM86 Express LPC Controller (rev 05)
00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05)
00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller (rev 05)
02:00.0 Network controller: Intel Corporation Wireless 7260 (rev 73)
03:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTL8411B PCI Express Card Reader (rev 01)
03:00.1 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 12)
uname -a
Linux laptop 4.15.14-300.fc27.x86_64 #1 SMP Thu Mar 29 16:13:44 UTC 2018 x86_64 x86_64 x86_64 GNU/Linux
 sensors
acpitz-virtual-0
Adapter: Virtual device
temp1:        +14.0°C  (crit = +120.0°C)

coretemp-isa-0000
Adapter: ISA adapter
Package id 0:  +35.0°C  (high = +84.0°C, crit = +100.0°C)
Core 0:        +32.0°C  (high = +84.0°C, crit = +100.0°C)
Core 1:        +34.0°C  (high = +84.0°C, crit = +100.0°C)

Il s'agit d'un laptop clevo vendu sur le site LDLC sans OS. Modèle plus dispo.

Dernière modification par ottovonstein (13/04/2018 21:40:01)


Otto! Rocking for a free World!!!

Hors ligne

#2 14/04/2018 10:49:06

Refuznik
Membre
Inscription : 31/01/2007
Messages : 6 959

Re : [Résolu] ventilos devenu fous

Que renvoie la commande sensors-detect et pwmconfig ?
Dans ton bios tu peux modifier les paramètres de ton ventilo ?

Hors ligne

#3 17/04/2018 22:01:24

ottovonstein
Membre
Inscription : 10/03/2010
Messages : 118

Re : [Résolu] ventilos devenu fous

Je viens de rallumer le laptop et tout est rentré dans l'ordre....
Je vais passer pour l'ane de service mais bon. L'autre soir rien a faire malgrés les reboot...


# sensors-detect revision 6284 (2015-05-31 14:00:33 +0200)
# System: Notebook W54_55SU1,SUW [Not Applicable] (laptop)
# Kernel: 4.15.14-300.fc27.x86_64 x86_64
# Processor: Intel(R) Pentium(R) CPU 3550M @ 2.30GHz (6/60/3)

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): yes 
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   No
AMD Family 10h thermal sensors...                           No
AMD Family 11h thermal sensors...                           No
AMD Family 12h and 14h thermal sensors...                   No
AMD Family 15h thermal sensors...                           No
AMD Family 16h thermal sensors...                           No
AMD Family 15h power sensors...                             No
AMD Family 16h power sensors...                             No
Intel digital thermal sensor...                             Success!
    (driver `coretemp')
Intel AMB FB-DIMM thermal sensor...                         No
Intel 5500/5520/X58 thermal sensor...                       No
VIA C7 thermal sensor...                                    No
VIA Nano thermal sensor...                                  No

Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): y
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor/ITE'...               Yes
Found unknown chip with ID 0x8587
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor/ITE'...               No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               No
Trying family `ITE'...                                      No

Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (YES/no): yes
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No

Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): yes
Using driver `i2c-i801' for device 0000:00:1f.3: Intel Lynx Point (PCH)
Module i2c-dev loaded successfully.

Next adapter: i915 gmbus ssc (i2c-0)
Do you want to scan it? (yes/NO/selectively): yes

Next adapter: i915 gmbus vga (i2c-1)
Do you want to scan it? (yes/NO/selectively): yes

Next adapter: i915 gmbus panel (i2c-2)
Do you want to scan it? (yes/NO/selectively): yes

Next adapter: i915 gmbus dpc (i2c-3)
Do you want to scan it? (yes/NO/selectively): yes

Next adapter: i915 gmbus dpb (i2c-4)
Do you want to scan it? (yes/NO/selectively): yes

Next adapter: i915 gmbus dpd (i2c-5)
Do you want to scan it? (yes/NO/selectively): yes

Next adapter: DPDDC-A (i2c-6)
Do you want to scan it? (yes/NO/selectively): ye

Next adapter: SMBus I801 adapter at f040 (i2c-7)
Do you want to scan it? (YES/no/selectively): yes


Now follows a summary of the probes I have just done.
Just press ENTER to continue:    

Driver `coretemp':
  * Chip `Intel digital thermal sensor' (confidence: 9)

Do you want to overwrite /etc/sysconfig/lm_sensors? (YES/no): yes
Unloading i2c-dev... OK
# pwmconfig revision 6243 (2014-03-20)
This program will search your sensors for pulse width modulation (pwm)
controls, and test each one to see if it controls a fan on
your motherboard. Note that many motherboards do not have pwm
circuitry installed, even if your sensor chip supports pwm.

We will attempt to briefly stop each fan using the pwm controls.
The program will attempt to restore each fan to full speed
after testing. However, it is ** very important ** that you
physically verify that the fans have been to full speed
after the program has completed.

/sbin/pwmconfig: There are no pwm-capable sensor modules installed

Otto! Rocking for a free World!!!

Hors ligne

#4 18/04/2018 08:54:49

Nednet
Membre
Lieu : aux alentours de Toulouse
Inscription : 07/12/2015
Messages : 293

Re : [Résolu] ventilos devenu fous

à tout hasard, tu as été regarder dans les paramètres du bios ? Je doute qu'un émulateur puisse les changer bien sûr, mais le hard reboot, pourquoi pas ?


Il n'y a aucune honte à ne pas savoir
mais beaucoup à ne pas apprendre

Hors ligne

#5 18/04/2018 13:47:15

VINDICATORs
RédactWikix and the graphicatorix!
Modérateur
Lieu : Toulouse(31) France
Inscription : 23/11/2004
Messages : 17 123
Site Web

Re : [Résolu] ventilos devenu fous

Petite astuce pour vider les condensateurs chimique (à voir si c'est la même chose avec les non chimique) qui ne fait pas de mal et évite d'avoir ce genre de comportement :
Reste appuyer quelques secondes (dans les 10s) sur le bouton pour allumer l'ordi après avoir débranché le secteur+batterie.

A tout les coups cela avait mémorisé quelque chose.


AMD Ryzen 7 2700X + MSI Gaming Pro Carbon X470, 32Go de RAM DDR4 3000Mhz Gskill Ageia C16, ATI R9 290x 4Go GDDR5
SSD Samsung 970 NVME 500Go et 850 EVO 250Go + 1x2To WD black 64Mo + 1x4to WD Black 128Mo + 3To WD red
Boitier GMT Bequiet Dark 900 + Lepa 800W 80+gold

Hors ligne

Pied de page des forums