bonjour,
voici ce que je trouve dans le log, pas sûr que ca aide :
[ 239.353] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse0)
[ 239.353] (II) No input driver/identifier specified (ignoring)
[ 239.376] (II) intel(0): EDID vendor "AUO", prod id 14100
[ 239.376] (II) intel(0): Printing DDC gathered Modelines:
[ 239.376] (II) intel(0): Modeline "1280x800"x0.0 71.11 1280 1328 1360 1440 800 803 809 823 -hsync -vsync (49.4 kHz)
[ 239.854] (II) intel(0): EDID vendor "AUO", prod id 14100
[ 239.856] (II) intel(0): Printing DDC gathered Modelines:
[ 239.856] (II) intel(0): Modeline "1280x800"x0.0 71.11 1280 1328 1360 1440 800 803 809 823 -hsync -vsync (49.4 kHz)
[ 239.938] (II) intel(0): EDID vendor "AUO", prod id 14100
[ 239.938] (II) intel(0): Printing DDC gathered Modelines:
[ 239.938] (II) intel(0): Modeline "1280x800"x0.0 71.11 1280 1328 1360 1440 800 803 809 823 -hsync -vsync (49.4 kHz)
[ 240.012] (II) intel(0): EDID vendor "AUO", prod id 14100
[ 240.012] (II) intel(0): Printing DDC gathered Modelines:
[ 240.012] (II) intel(0): Modeline "1280x800"x0.0 71.11 1280 1328 1360 1440 800 803 809 823 -hsync -vsync (49.4 kHz)
[ 240.077] (II) intel(0): EDID vendor "AUO", prod id 14100
[ 240.077] (II) intel(0): Printing DDC gathered Modelines:
[ 240.077] (II) intel(0): Modeline "1280x800"x0.0 71.11 1280 1328 1360 1440 800 803 809 823 -hsync -vsync (49.4 kHz)
[ 251.906] (II) intel(0): EDID vendor "AUO", prod id 14100
[ 251.912] (II) intel(0): Printing DDC gathered Modelines:
[ 251.912] (II) intel(0): Modeline "1280x800"x0.0 71.11 1280 1328 1360 1440 800 803 809 823 -hsync -vsync (49.4 kHz)
[ 252.004] (II) intel(0): EDID vendor "AUO", prod id 14100
[ 252.004] (II) intel(0): Printing DDC gathered Modelines:
[ 252.004] (II) intel(0): Modeline "1280x800"x0.0 71.11 1280 1328 1360 1440 800 803 809 823 -hsync -vsync (49.4 kHz)
[ 252.082] (II) intel(0): EDID vendor "AUO", prod id 14100
[ 252.082] (II) intel(0): Printing DDC gathered Modelines:
[ 252.082] (II) intel(0): Modeline "1280x800"x0.0 71.11 1280 1328 1360 1440 800 803 809 823 -hsync -vsync (49.4 kHz)
[ 252.169] (II) intel(0): Allocated new frame buffer 1728x1050 stride 7168, tiled
[ 253.806] (II) intel(0): EDID vendor "AUO", prod id 14100
[ 253.811] (II) intel(0): Printing DDC gathered Modelines:
[ 253.811] (II) intel(0): Modeline "1280x800"x0.0 71.11 1280 1328 1360 1440 800 803 809 823 -hsync -vsync (49.4 kHz)
Il y a quand même des avancées dans mon problème :-D
Si je quitte la session et que je me reconnecte, il a l'air de fonctionner, mais quand je branche l'écran c'est la cata car il veut éteindre mon écran principal direct. Hier soir, j'ai fais un test concluant. En branchant l'écran et désactivant l'écran principal pour passer le 22 pouces en principal -> cata
En branchant l'écran, paramétrant le 22 à la même résolution que le principal puis désactivant le principal -> ok. Il reste plus qu'à configurer le principal en 1680/1060 et ca marche. Un petit souci à priori lorsqu'il essaye de passer direct de l'écran du portable au 22 avec la résolution du 22 🙂