[root@localhost ~]# modprobe pppoatm
[root@localhost ~]# pppd call ueagle-atm
Plugin pppoatm.so loaded.
PPPoATM plugin_init
PPPoATM setdevname_pppoatm - SUCCESS:8.35
[root@localhost ~]#
Puis: [root@localhost ~]# grep pppd /var/log/messages
Feb 27 23:41:20 localhost pppd[3140]: Plugin pppoatm.so loaded.
Feb 27 23:41:20 localhost pppd[3140]: PPPoATM plugin_init
Feb 27 23:41:20 localhost pppd[3140]: PPPoATM setdevname_pppoatm - SUCCESS:8.35
Feb 27 23:41:20 localhost pppd[3141]: pppd 2.4.4 started by root, uid 0
Feb 27 23:41:20 localhost pppd[3141]: Using interface ppp0
Feb 27 23:41:20 localhost pppd[3141]: Connect: ppp0 <--> 8.35
Feb 27 23:41:20 localhost pppd[3141]: Couldn't increase MTU to 1500. Using 1492
Feb 27 23:41:20 localhost pppd[3141]: Couldn't increase MRU to 1500. Using 1492
Feb 27 23:41:50 localhost pppd[3141]: LCP: timeout sending Config-Requests
Feb 27 23:41:50 localhost pppd[3141]: Connection terminated.
Feb 27 23:41:50 localhost pppd[3141]: Modem hangup
Feb 27 23:42:20 localhost pppd[3141]: Using interface ppp0
Feb 27 23:42:20 localhost pppd[3141]: Connect: ppp0 <--> 8.35
Feb 27 23:42:20 localhost pppd[3141]: Couldn't increase MTU to 1500. Using 1492
Feb 27 23:42:20 localhost pppd[3141]: Couldn't increase MRU to 1500. Using 1492
---------------------------------------------------------------------------------------
[root@localhost ~]# fdisk -l
Disk /dev/sda: 203.9 GB, 203928109056 bytes
255 heads, 63 sectors/track, 24792 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 * 1 9493 76252491 7 HPFS/NTFS
/dev/sda2 9494 24791 122881185 f W95 Ext'd (LBA)
/dev/sda5 9494 24791 122881153+ 7 HPFS/NTFS
Disk /dev/sdb: 203.9 GB, 203928109056 bytes
255 heads, 63 sectors/track, 24792 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sdb1 * 151 24792 197936865 83 Linux
/dev/sdb2 1 150 1204843+ 82 Linux swap / Solaris
Partition table entries are not in disk order
-------------------------------------------------------------------------------------------
Commande dmesg
Linux version 2.6.18-1.2798.fc6 (
brewbuilder@hs20-bc2-4.build.redhat.com) (gcc version 4.1.1 20061011 (Red Hat 4.1.1-30)) #1 SMP Mon Oct 16 14:37:32 EDT 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f5240
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 262128
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 32752 pages, LIFO batch:7
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v000 Nvidia ) @ 0x000f9100
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3040
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff30c0
ACPI: SRAT (v001 AMD HAMMER 0x00000001 AMD 0x00000001) @ 0x3fff9680
ACPI: MCFG (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff9780
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff95c0
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:15 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
Detected 2211.357 MHz processor.
Built 1 zonelists. Total pages: 262128
Kernel command line: ro root=LABEL=/ rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c07ae000 soft=c078e000
PID hash table entries: 4096 (order: 12, 16384 bytes)
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1032772k/1048512k available (2138k kernel code, 14904k reserved, 868k data, 240k init, 131008k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4425.40 BogoMIPS (lpj=8850808)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 078bf3ff e3d3fbff 00000000 00000410 00000001 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20060707
CPU0: AMD Athlon(tm) 64 Processor 3500+ stepping 02
Total of 1 processors activated (4425.40 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
Brought up 1 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=424 bytes
sizeof(dentry)=148 bytes
sizeof(ext3inode)=600 bytes
sizeof(buffer_head)=52 bytes
sizeof(skbuff)=172 bytes
sizeof(task_struct)=1392 bytes
checking if image is initramfs... it is
Freeing initrd memory: 1476k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
PCI: No mmconfig possible on 0:18
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:09.0
Boot video device is 0000:05:00.0
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:01: ioport range 0x4000-0x407f could not be reserved
pnp: 00:01: ioport range 0x4080-0x40ff has been reserved
pnp: 00:01: ioport range 0x4400-0x447f has been reserved
pnp: 00:01: ioport range 0x4480-0x44ff could not be reserved
pnp: 00:01: ioport range 0x4800-0x487f has been reserved
pnp: 00:01: ioport range 0x4880-0x48ff has been reserved
PCI: Bridge: 0000:00:09.0
IO window: d000-dfff
MEM window: fe900000-fe9fffff
PREFETCH window: fea00000-feafffff
PCI: Bridge: 0000:00:0b.0
IO window: c000-cfff
MEM window: fe800000-fe8fffff
PREFETCH window: fe700000-fe7fffff
PCI: Bridge: 0000:00:0c.0
IO window: b000-bfff
MEM window: fe600000-fe6fffff
PREFETCH window: fe500000-fe5fffff
PCI: Bridge: 0000:00:0d.0
IO window: a000-afff
MEM window: fe400000-fe4fffff
PREFETCH window: fe300000-fe3fffff
PCI: Bridge: 0000:00:0e.0
IO window: 9000-9fff
MEM window: fe200000-fe2fffff
PREFETCH window: d0000000-dfffffff
PCI: Setting latency timer of device 0000:00:09.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 9, 2621440 bytes)
TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1172618895.580:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 8BDC589434DBC709
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Linking AER extended capability on 0000:00:0b.0
PCI: Linking AER extended capability on 0000:00:0c.0
PCI: Linking AER extended capability on 0000:00:0d.0
PCI: Linking AER extended capability on 0000:00:0e.0
PCI: Setting latency timer of device 0000:00:0b.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
Allocate Port Service[0000:00:0b.0:pcie03]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
Allocate Port Service[0000:00:0c.0:pcie03]
PCI: Setting latency timer of device 0000:00:0d.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
Allocate Port Service[0000:00:0d.0:pcie03]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
Allocate Port Service[0000:00:0e.0:pcie03]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (on)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x1
ACPI: Thermal Zone [THRM] (22 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 242
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
ide0: BM-DMA at 0xfb00-0xfb07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfb08-0xfb0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
hdb: HL-DT-STDVD-ROM GDR8163B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3500+ processors (version 2.00.00)
powernow-k8: BIOS error - no PSB or ACPI _PSS objects
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 240k freed
Write protecting the kernel read-only data: 386k
Time: tsc clocksource has been installed.
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 217, io mem 0xfebff000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.1
-> Link [APCL] -> GSI 22 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 225, io mem 0xfeb00000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
SCSI subsystem initialized
libata version 2.00 loaded.
sata_nv 0000:00:07.0: version 2.0
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 21 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:07.0 to 64
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xF600 irq 233
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xF608 irq 233
scsi0 : sata_nv
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7, max UDMA/133, 398297088 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : sata_nv
ohci_hcd 0000:00:02.0: wakeup
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATA-7, max UDMA/133, 398297088 sectors: LBA48 NCQ (depth 0/32)
ata2.00: ata2: dev 0 multi count 16
ata2.00: configured for UDMA/133
Vendor: ATA Model: Maxtor 6L200S0 Rev: BACE
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 >
sd 0:0:0:0: Attached scsi disk sda
Vendor: ATA Model: Maxtor 6V200E0 Rev: VA11
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 398297088 512-byte hdwr sectors (203928 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 398297088 512-byte hdwr sectors (203928 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2
sd 1:0:0:0: Attached scsi disk sdb
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 20 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:08.0 to 64
ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xF100 irq 50
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xF108 irq 50
scsi2 : sata_nv
usb 1-2: new full speed USB device using ohci_hcd and address 2
ata3: SATA link down (SStatus 0 SControl 300)
scsi3 : sata_nv
ata4: SATA link down (SStatus 0 SControl 300)
usb 1-2: configuration #1 chosen from 1 choice
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb 1-7: new full speed USB device using ohci_hcd and address 3
usb 1-7: configuration #1 chosen from 1 choice
usb 1-8: new low speed USB device using ohci_hcd and address 4
usb 1-8: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /class/input/input0
input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:02.0-8
input: Logitech USB Receiver as /class/input/input1
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:02.0-8
audit(1172618904.144:2): enforcing=1 old_enforcing=0 auid=4294967295
security: 3 users, 6 roles, 1560 types, 166 bools, 1 sens, 1024 cats
security: 58 classes, 48173 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev sdb1, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), not configured for labeling
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1172618904.432:3): policy loaded auid=4294967295
Linux video capture interface: v2.00
pwc: Unknown parameter `index'
hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdb: ATAPI 52X DVD-ROM drive, 256kB Cache, UDMA(33)
NET: Registered protocol family 8
NET: Registered protocol family 20
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.56.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:0a.0 to 64
forcedeth: using HIGHDMA
pwc: Unknown parameter `index'
[ueagle-atm] driver ueagle 1.3 loaded
usb 1-7: [ueagle-atm] ADSL device founded vid (0X1110) pid (0X900F) : Eagle I
input: PC Speaker as /class/input/input2
EDAC MC: Ver: 2.0.1 Oct 16 2006
usb 1-7: reset full speed USB device using ohci_hcd and address 3
eth0: forcedeth.c: subsystem: 01462:7125 bound to 0000:00:0a.0
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40
EDAC MC0: Giving out device to k8_edac Athlon64/Opteron: DEV 0000:00:18.2
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
usb 1-7: [ueagle-atm] using iso mode
usb 1-7: [ueagle-atm] (re)booting started
ATM dev 0: usbatm_submit_urb: urb 0xf7240b80 submission failed (-28)!
usbcore: registered new driver ueagle-atm
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCJ] -> GSI 22 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:04.0 to 64
intel8x0_measure_ac97_clock: measured 58690 usecs
intel8x0: clocking to 46952
usbcore: registered new driver snd-usb-audio
pwc: Unknown parameter `index'
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
lp0: console ready
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 58
[drm] Initialized radeon 1.25.0 20060524 on minor 0
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
EXT3 FS on sdb1, internal journal
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 1204832k swap on /dev/sdb2. Priority:-1 extents:1 across:1204832k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8191 buckets, 65528 max) - 228 bytes per conntrack
usb 1-7: [ueagle-atm] modem operational
usb 1-7: [ueagle-atm] ATU-R firmware version : 44e2ea17
eth0: no link during initialization.
ADDRCONF(NETDEV_UP): eth0: link is not ready
audit(1172615329.668:4): audit_pid=2078 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
SELinux: initialized (dev nfsd, type nfsd), uses genfs_contexts
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
[drm] Setting GART location based on new memory map
[drm] Loading R300 Microcode