Alors, pour l'utilisation du wpa avec ce driver, il faut apparemment utiliser wpa_supplicant.
Cependant, je ne sais pas avec quel driver : wext?
Voilà le résultat de la commande :
[root@localhost ~]# wpa_supplicant -d -Dwext -c /etc/wpa_supplicant/wpa_supplicant.conf -ieth0
Initializing interface 'eth0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group=0
eapol_version=1
ap_scan=1
fast_reauth=1
Priority group 0
id=0 ssid='TECOM-AH4222-56560A'
Initializing interface (2) 'eth0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=20 WE(source)=19 enc_capa=0x0
capabilities: key_mgmt 0x0 enc 0x3
Own MAC address: 00:0x:xx:xx:xx:xx
wpa_driver_wext_set_wpa
[b]ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 7 value 0x1 - Driver does not support WPA.
[/b]wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 4 value 0x0 - wpa_driver_wext_set_drop_unencrypted
Setting scan request: 0 sec 100000 usec
Added interface eth0
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
CTRL-EVENT-TERMINATING - signal 2 received
Removing interface eth0
State: SCANNING -> DISCONNECTED
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_wext_set_wpa
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_countermeasures
ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 4 value 0x0 - No keys have been configured - skip key clearing
Cancelling scan request
Donc là, j'ai un avis contraire...
Bref, je suis assez perdu comme je le disais dans mon premier message !