Bonjour, je sais que cela ne concerne pas directement fedora, d'autant qu'il s'agit du HDD de mon raspberry (torrent, seafile, serveur dlna, web, bref, il fait tout plein de trucs ce petit machin!!) bref, mon disque du déconne. Je l'ai branché sur mon PC (lui est sous fedora 24) et ai lancé smartmontool. le rapport donne des erreurs mais je ne sais pas les interpréter. Le HDD a 3 ans mais tourne h24 sur le raspi depuis un an environ. Un formatage devrait suffire ou il semble plutôt cuit? J'ai déjà passé le disque deux fois en checkdisk via gparted. J'ai des sauvegardes mais pas d'autre HDD et je ne voudrais pas qu'il me plante une heure apres avoir erstauré mes 800Go de films et musique dessus : meme en usb3 c'est long... Voici le rapport :
smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.7.2-201.fc24.x86_64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST1000DM003-1CH162
Serial Number: Z1D65JRR
LU WWN Device Id: 5 000c50 064841b26
Firmware Version: CC47
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Fri Sep 9 10:20:36 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 584) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 114) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3085) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 076 076 006 Pre-fail Always - 100299653
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 096 096 020 Old_age Always - 4469
5 Reallocated_Sector_Ct 0x0033 085 085 010 Pre-fail Always - 17016
7 Seek_Error_Rate 0x000f 071 060 030 Pre-fail Always - 4309541813
9 Power_On_Hours 0x0032 087 087 000 Old_age Always - 12158
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1026
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 801
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 4 4 4
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 062 044 045 Old_age Always In_the_past 38 (0 3 38 36 0)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 227
193 Load_Cycle_Count 0x0032 071 071 000 Old_age Always - 58860
194 Temperature_Celsius 0x0022 038 056 000 Old_age Always - 38 (0 11 0 0 0)
197 Current_Pending_Sector 0x0012 072 072 000 Old_age Always - 4712
198 Offline_Uncorrectable 0x0010 072 072 000 Old_age Offline - 4712
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 4259h+08m+11.084s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 8648309953
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 21905491194
SMART Error Log Version: 1
ATA Error Count: 799 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 799 occurred at disk power-on lifetime: 12158 hours (506 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff 4f 00 00:00:23.469 READ DMA EXT
25 00 d0 ff ff ff 4f 00 00:00:22.642 READ DMA EXT
25 00 00 ff ff ff 4f 00 00:00:20.168 READ DMA EXT
25 00 00 00 03 00 40 00 00:00:20.167 READ DMA EXT
25 00 00 00 02 00 40 00 00:00:20.166 READ DMA EXT
Error 798 occurred at disk power-on lifetime: 12158 hours (506 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:26:07.026 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:26:07.026 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:26:07.026 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:26:07.025 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:26:07.021 READ FPDMA QUEUED
Error 797 occurred at disk power-on lifetime: 12158 hours (506 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:21:41.221 READ FPDMA QUEUED
25 03 08 ff ff ff 4f 00 00:21:40.208 READ DMA EXT
ef 03 46 e0 f1 ca 00 00 00:21:40.208 SET FEATURES [Set transfer mode]
ef 03 0c e0 f1 ca 00 00 00:21:40.207 SET FEATURES [Set transfer mode]
ec 03 08 e0 f1 ca 00 00 00:21:40.207 IDENTIFY DEVICE
Error 796 occurred at disk power-on lifetime: 12158 hours (506 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:21:35.378 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:21:34.228 READ FPDMA QUEUED
25 03 08 ff ff ff 4f 00 00:21:33.157 READ DMA EXT
ef 03 46 a0 f0 ca 00 00 00:21:33.156 SET FEATURES [Set transfer mode]
ef 03 0c a0 f0 ca 00 00 00:21:33.156 SET FEATURES [Set transfer mode]
Error 795 occurred at disk power-on lifetime: 12158 hours (506 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 40 ff ff ff 4f 00 00:21:26.343 READ FPDMA QUEUED
60 00 40 ff ff ff 4f 00 00:21:26.343 READ FPDMA QUEUED
60 00 40 ff ff ff 4f 00 00:21:26.282 READ FPDMA QUEUED
60 00 40 ff ff ff 4f 00 00:21:26.282 READ FPDMA QUEUED
60 00 40 ff ff ff 4f 00 00:21:26.276 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
J'attends vos avis! Ciao et merci d'avance!!