C'est des erreurs de lectures de fichiers, ça peut être dût à plusieurs facteurs (erreur de transmission, dans le fichier, plantage en cours de transfert, etc...).
Perso ça tourne à 26°C->29°C en plein été... quoi qu'ici c'est plus humide que chez vous...
[root@zeus ~]# smartctl -a /dev/sda
smartctl version 5.38 [x86_64-redhat-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.11
Device Model: ST3500320AS
Serial Number: 9QM6PG0Y
Firmware Version: SD15
User Capacity: 500 107 862 016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Fri Mar 27 08:20:45 2009 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 650) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 117) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 114 099 006 Pre-fail Always - [b]69517119[/b]
3 Spin_Up_Time 0x0003 095 094 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 122
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 075 060 030 Pre-fail Always - [b]4328177974[/b]
9 Power_On_Hours 0x0032 096 096 000 Old_age Always - 4215
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 1
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 121
184 Unknown_Attribute 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Unknown_Attribute 0x0032 100 098 000 Old_age Always - 4
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 074 066 045 Old_age Always - 26 (Lifetime Min/Max 19/26)
194 Temperature_Celsius 0x0022 026 040 000 Old_age Always - 26 (0 12 0 0)
195 Hardware_ECC_Recovered 0x001a 044 039 000 Old_age Always - [b]69517119[/b]
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - [b]1[/b]
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Là le disque fonctionne comme il faut...
Si vous vous voulez un disque qui commence à rendre l'âme petit à petit (quoi que cela fait 2 ans que ça se sent alors qu'il est toujours en vie depuis 2003...). Par contre il ne m'a jamais fait autant d'erreur de lecture que le seagate??? mais il faut savoir qu'il tourne moins rapidement que le seagate, car c'est un SATA150 batârd car en fait un UDMA100/133 modifié pour tourner sur du SATA, alors que le seagate est en SATA300 natif :
[root@zeus ~]# smartctl -a /dev/sdb
smartctl version 5.38 [x86_64-redhat-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Maxtor DiamondMax Plus 9 family
Device Model: Maxtor 6Y120M0
Serial Number: Y3JXW9WE
Firmware Version: YAR51BW0
User Capacity: 122 942 324 736 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Fri Mar 27 08:24:12 2009 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 242) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 54) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 200 196 063 Pre-fail Always - 11778
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 954
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 2
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0
8 Seek_Time_Performance 0x0027 253 247 187 Pre-fail Always - 55145
9 Power_On_Minutes 0x0032 198 198 000 Old_age Always - 784h+49m
10 Spin_Retry_Count 0x002b 253 250 157 Pre-fail Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 248 248 000 Old_age Always - 2286
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age Always - 42
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 7970
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 194 000 Old_age Offline - 5
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 251 000 Old_age Always - 337
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 16
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0
207 Spin_High_Current 0x002a 253 250 000 Old_age Always - 0
208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0
209 Offline_Seek_Performnce 0x0024 191 191 000 Old_age Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
SMART Error Log Version: 1
Warning: ATA error count 58 inconsistent with error log pointer 5
ATA Error Count: 58 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 58 occurred at disk power-on lifetime: 13917 hours (579 days + 21 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 77 23 50 e3 Error: ICRC, ABRT at LBA = 0x03502377 = 55583607
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 77 23 50 e3 00 19:14:43.088 READ DMA
c8 00 08 9f 1b 3c e3 00 19:14:43.072 READ DMA
c8 00 10 6f d5 a9 e0 00 19:14:43.056 READ DMA
c8 00 08 6f 10 a8 e0 00 19:14:43.056 READ DMA
c8 00 08 4f 00 a8 e0 00 19:14:43.056 READ DMA
Error 57 occurred at disk power-on lifetime: 9919 hours (413 days + 7 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 c7 bc 56 e1 Error: ICRC, ABRT at LBA = 0x0156bcc7 = 22461639
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 c7 bc 56 e1 00 08:59:19.264 READ DMA
c8 00 10 1f 47 49 e1 00 08:59:19.264 READ DMA
c8 00 17 00 47 49 e1 00 08:59:19.264 READ DMA
c8 00 19 67 15 44 e1 00 08:59:19.264 READ DMA
c8 00 5f 00 15 44 e1 00 08:59:19.264 READ DMA
Error 56 occurred at disk power-on lifetime: 9909 hours (412 days + 21 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 97 01 60 e1 Error: ICRC, ABRT at LBA = 0x01600197 = 23069079
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 97 01 60 e1 00 00:07:32.064 READ DMA
c8 00 10 17 e2 60 e1 00 00:07:32.064 READ DMA
c8 00 08 77 7b 61 e1 00 00:07:32.064 READ DMA
c8 00 08 9f e2 60 e1 00 00:07:32.064 READ DMA
c8 00 08 6f 69 61 e1 00 00:07:32.048 READ DMA
Error 55 occurred at disk power-on lifetime: 9909 hours (412 days + 21 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 4f 00 84 e1 Error: ICRC, ABRT at LBA = 0x0184004f = 25428047
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 4f 00 84 e1 00 00:06:53.280 READ DMA
c8 00 18 e7 b0 43 e1 00 00:06:53.280 READ DMA
c8 00 10 a7 b0 43 e1 00 00:06:53.264 READ DMA
c8 00 07 00 b6 4e e1 00 00:06:53.248 READ DMA
c8 00 01 ff af 43 e1 00 00:06:53.248 READ DMA
Error 54 occurred at disk power-on lifetime: 9898 hours (412 days + 10 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 04 00 61 12 e2 Error: UNC 4 sectors at LBA = 0x02126100 = 34758912
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 5f 00 61 12 e2 00 00:06:33.696 READ DMA
ec ff 00 5b 61 12 a0 00 00:06:33.680 IDENTIFY DEVICE
c8 00 5f 00 61 12 e2 00 00:07:38.208 READ DMA
ec ff 00 5b 61 12 a0 00 00:07:38.208 IDENTIFY DEVICE
c8 00 5f 00 61 12 e2 00 00:07:37.200 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Par contre lui à connu les 52°C, lors de l'été 2003/2004... (actuellement 39/43°C)
Et je ne vous montre pas le deuxième que j'ai dût enlever car lui à vraiment montrer qu'il rendait l'âme!