Hello! j'ai été assez pris ces jours ci, mais pour ma culture perso, j'aimerais savoir de quoi il retourne avec ce HDD : Je poste le rapport smart dans la foulée. Quelqu'un peut m'en dire plus, ou un lien ou chercher ce qu'il faut regarder d'important? Merci!
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.2-200.fc28.x86_64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: HGST Travelstar 5K1000
Device Model: HGST HTS541010A9E680
Serial Number: JD1008DM07XTKW
LU WWN Device Id: 5 000cca 827c39aae
Firmware Version: JA0OA560https://shoppingcart.aliexpress.com/shopcart/shopcartDetail.htm?spm=a2g0s.8916898.1000002.2.662fOCKIOCKI1k
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Fri Nov 30 16:54:20 2018 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 1 (minimum power consumption with standby)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, NOT FROZEN [SEC1]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 45) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 249) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0
2 Throughput_Performance P-S--- 195 195 040 - 279
3 Spin_Up_Time POS--- 185 185 033 - 1
4 Start_Stop_Count -O--C- 094 094 000 - 9807
5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0
7 Seek_Error_Rate PO-R-- 100 100 067 - 0
8 Seek_Time_Performance P-S--- 117 117 040 - 33
9 Power_On_Hours -O--C- 091 091 000 - 4345
10 Spin_Retry_Count PO--C- 100 100 060 - 0
12 Power_Cycle_Count -O--CK 099 099 000 - 2117
191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0
192 Power-Off_Retract_Count -O--CK 100 100 000 - 97
193 Load_Cycle_Count -O--C- 097 097 000 - 33917
194 Temperature_Celsius -O---- 222 222 000 - 27 (Min/Max 6/50)
196 Reallocated_Event_Count -O--CK 100 100 000 - 1
197 Current_Pending_Sector -O---K 100 100 000 - 56
198 Offline_Uncorrectable ---R-- 100 100 000 - 0
199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0
223 Load_Retry_Count -O-R-- 100 100 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 1 Comprehensive SMART error log
0x03 GPL R/O 1 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Device Error Count: 5514 (device log contains only the most recent 4 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 5514 [1] occurred at disk power-on lifetime: 4325 hours (180 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 00 00 69 2c 4f 00 00 Error: UNC 1 sectors at LBA = 0x00692c4f = 6892623
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 01 00 00 00 69 2c 4f 40 00 00:03:36.384 READ DMA EXT
25 00 00 00 01 00 00 00 69 2c 4e 00 04 00:03:36.358 READ DMA EXT
25 00 00 00 01 00 00 00 69 2c 4e 40 00 00:03:32.462 READ DMA EXT
25 00 00 00 01 00 00 00 69 2c 4d 00 04 00:03:32.436 READ DMA EXT
25 00 00 00 01 00 00 00 69 2c 4d 40 00 00:03:28.540 READ DMA EXT
Error 5513 [0] occurred at disk power-on lifetime: 4325 hours (180 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 00 00 69 2c 4e 00 00 Error: UNC 1 sectors at LBA = 0x00692c4e = 6892622
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 01 00 00 00 69 2c 4e 40 00 00:03:32.462 READ DMA EXT
25 00 00 00 01 00 00 00 69 2c 4d 00 04 00:03:32.436 READ DMA EXT
25 00 00 00 01 00 00 00 69 2c 4d 40 00 00:03:28.540 READ DMA EXT
25 00 00 00 01 00 00 00 69 2c 4c 00 04 00:03:28.514 READ DMA EXT
25 00 00 00 01 00 00 00 69 2c 4c 40 00 00:03:24.617 READ DMA EXT
Error 5512 [3] occurred at disk power-on lifetime: 4325 hours (180 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 00 00 69 2c 4d 00 00 Error: UNC 1 sectors at LBA = 0x00692c4d = 6892621
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 01 00 00 00 69 2c 4d 40 00 00:03:28.540 READ DMA EXT
25 00 00 00 01 00 00 00 69 2c 4c 00 04 00:03:28.514 READ DMA EXT
25 00 00 00 01 00 00 00 69 2c 4c 40 00 00:03:24.617 READ DMA EXT
25 00 00 00 01 00 00 00 69 2c 4b 00 04 00:03:24.591 READ DMA EXT
25 00 00 00 01 00 00 00 69 2c 4b 40 00 00:03:20.695 READ DMA EXT
Error 5511 [2] occurred at disk power-on lifetime: 4325 hours (180 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 00 00 69 2c 4c 00 00 Error: UNC 1 sectors at LBA = 0x00692c4c = 6892620
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 01 00 00 00 69 2c 4c 40 00 00:03:24.617 READ DMA EXT
25 00 00 00 01 00 00 00 69 2c 4b 00 04 00:03:24.591 READ DMA EXT
25 00 00 00 01 00 00 00 69 2c 4b 40 00 00:03:20.695 READ DMA EXT
25 00 00 00 01 00 00 00 69 2c 4a 00 04 00:03:20.669 READ DMA EXT
25 00 00 00 01 00 00 00 69 2c 4a 40 00 00:03:16.773 READ DMA EXT
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 27 Celsius
Power Cycle Min/Max Temperature: 17/28 Celsius
Lifetime Min/Max Temperature: 6/50 Celsius
Lifetime Average Temperature: 31 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -40/65 Celsius
Temperature History Size (Index): 128 (15)
Index Estimated Time Temperature Celsius
16 2018-11-30 14:47 24 *****
... ..( 75 skipped). .. *****
92 2018-11-30 16:03 24 *****
93 2018-11-30 16:04 23 ****
94 2018-11-30 16:05 24 *****
... ..( 15 skipped). .. *****
110 2018-11-30 16:21 24 *****
111 2018-11-30 16:22 25 ******
112 2018-11-30 16:23 24 *****
... ..( 10 skipped). .. *****
123 2018-11-30 16:34 24 *****
124 2018-11-30 16:35 25 ******
125 2018-11-30 16:36 24 *****
126 2018-11-30 16:37 24 *****
127 2018-11-30 16:38 24 *****
0 2018-11-30 16:39 25 ******
1 2018-11-30 16:40 24 *****
2 2018-11-30 16:41 24 *****
3 2018-11-30 16:42 25 ******
4 2018-11-30 16:43 24 *****
5 2018-11-30 16:44 25 ******
6 2018-11-30 16:45 24 *****
7 2018-11-30 16:46 26 *******
8 2018-11-30 16:47 27 ********
9 2018-11-30 16:48 28 *********
10 2018-11-30 16:49 28 *********
11 2018-11-30 16:50 28 *********
12 2018-11-30 16:51 27 ********
... ..( 2 skipped). .. ********
15 2018-11-30 16:54 27 ********
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 0 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS