Bonjour,
J'ai migré sans souci de la fédora26 à 27 hier soir
Sauf que j'ai eu le message suivant juste avant de télécharger les paquets pour la migration
Warning:your hard drive is failling
Device: /dev/sdc [SAT], UNABLE TO OPEN DEVICE
note SDC est le disque dur où s'est faite la migration.
je démarre sans souci en dual boot dessus depuis.
Ce matin je décide de faire une sauvegarde de mon nouveau système avec Clonezilla (comme d'habitude)
impossible, avec message suivant
Failed to use partclone programme to save or restore an image
Failed to save partition /dev/sdc1 (fedo27)
Ma question:
Soit c'est mon disque dur qui lâche
Soit la migration à changé quelque chose sur le dur mais quoi ? (je doute fort)
Quels outils puis-je utiliser pour vérifier mon disque dur ? et comment car là je suis sur la partition fedo27 monté!
Note: par la commande smartctl j'ai pu obtenir les infos suivantes
[root@localhost ~]# smartctl -a /dev/sdb1
smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.13.12-300.fc27.x86_64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F3
Device Model: SAMSUNG HD103SJ
Serial Number: S246J9DB203281
LU WWN Device Id: 5 0024e9 204892f18
Firmware Version: 1AJ10001
User Capacity: 1 000 204 886 016 bytes [1,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Mon Nov 20 09:42:18 2017 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 9120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 152) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 67
2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0
3 Spin_Up_Time 0x0023 070 068 025 Pre-fail Always - 9122
4 Start_Stop_Count 0x0032 095 095 000 Old_age Always - 5061
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 15527
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 252 252 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 095 095 000 Old_age Always - 5124
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 294
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 063 048 000 Old_age Always - 37 (Min/Max 14/52)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 100 100 000 Old_age Always - 8
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 171
223 Load_Retry_Count 0x0032 252 252 000 Old_age Always - 0
225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 5124
SMART Error Log Version: 1
ATA Error Count: 2
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2 occurred at disk power-on lifetime: 14655 hours (610 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 90 00 25 00 e0 Error: ICRC, ABRT 144 sectors at LBA = 0x00002500 = 9472
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 90 25 1e e4 08 00:00:00.026 READ DMA
c8 00 00 d8 27 1e e4 08 00:00:00.026 READ DMA
c8 00 f0 10 01 00 e0 08 00:00:00.026 READ DMA
c8 00 20 00 8d 8c e3 08 00:00:00.026 READ DMA
c8 00 08 58 21 81 e3 08 00:00:00.026 READ DMA
Error 1 occurred at disk power-on lifetime: 3645 hours (151 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 60 00 1f 00 e0 Error: ICRC, ABRT 96 sectors at LBA = 0x00001f00 = 7936
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 60 1f c2 e0 08 00:01:14.846 READ DMA
c8 00 20 f0 db 21 e0 08 00:01:14.846 READ DMA
c8 00 10 88 f4 4b e0 08 00:01:14.846 READ DMA
c8 00 08 70 dd 21 e0 08 00:01:14.846 READ DMA
c8 00 08 98 92 0f e0 08 00:01:14.846 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
merci
