Bonjour à tous!
Je suis débutante sous linux et je tente avec désespoir d'installer mon imprimante (canon ip 1800) sur fedora 23.
Les pilotes étant absant dans la base de données, je me suis rendue sur le site du constructeur (Canon Asia.com) pour faire fonctionner la bête. Ne trouvant rien de concluant, j'ai tout de même trouvée un guide d'installation du constructeur (qui sent un peut le renfermé mais bon...) pour fedora core 6.
Fedora Core 6
This section describes how to install a printer driver in Fedora Core 6.
If you want to install the printer driver, start Linux and log in as root.
Preparation
Installing the insufficient package
Depending on the selected installation type, the package required to install the printer driver may not be installed.
If such is the case, install the following packages before installing the printer driver:
libxml-1.8.17-xxx.i386.rpm
gtk+-1.2.xxx.i386.rpm
Make sure to install it as shown below:
# rpm -ivh gtk+-1.2.xxx.i386.rpm --nodeps
glib-1.2.xxx.i386.rpm
Changing the SELinux settings
The following settings are required if you cannot perform the printing operation:
1) Select [System] - [Administration] - [Security Level and Firewall] from the desktop panel.
2) Change the [SELinux Setting] on the [SELinux] tab to [Permissive].
Connecting the printer
Before installing the printer driver, connect the computer and the printer with a USB cable and turn on the printer.
Preparing the printer driver rpm
Before using the printer driver, you must install the "common package" and the "model-specific package."
cnijfilter-common-2.70-x.i386.rpm -------- Common package
cnijfilter-ip1800series-2.70-x.i386.rpm -------- Model-specific package
Download the above .rpm files from the Canon Web site in advance.
(Where "2.70-x" in the above .rpm files is the version number.)
Install
1. Install printer driver.
Install the printer driver in order of the "common package" and the "model-specific package" by using the rpm command from the command line of the terminal software.
1) Installing the common package
[root@zzz /yyy]# rpm -ivh cnijfilter-common-2.70-x.i386.rpm
2) Installing the model-specific package
[root@zzz /yyy]# rpm -ivh cnijfilter-ip1800series-2.70-x.i386.rpm
Refer to the following URL for the detailed information about the rpm command:
http://www.rpm.org/
2. Restart the CUPS daemon.
Enter the following from the command line of the terminal software:
[root@zzz /yyy]# /etc/init.d/cups restart
Do not register the printer with the lpadmin command before you restart the CUPS daemon.
3. Register the printer to the spooler.
Register the printer to the spooler by using the lpadmin command from the command line of the terminal software. You can specify the desired name as the [printer_name].
/usr/sbin/lpadmin -p [printer_name] -m [PPD_filename] -v [device_URI] -E
If you specify IP1800 as the [printer_name]:
[root@zzz /yyy]# /usr/sbin/lpadmin -p IP1800 -m canonip1800.ppd -v cnij_usb:/dev/usb/lp0 -E
4. Set the default printer.
Set the default printer to be used when the [printer_name] is omitted in the print command from the command line of the terminal software.
/usr/sbin/lpadmin -d [printer_name]
Example:
[root@zzz /yyy]# /usr/sbin/lpadmin -d IP1800
5. Restart the computer.
The following settings are required for printing with the Driver UI of the cif command:
Run the gdmsetup command.
Select the [Security] tab and uncheck the [Deny TCP connections to Xserver] check box.
Reboot the system.
The Status Monitor may not be displayed properly if the LAN environment has been configured and the IP address has been specified.
If such is the case, make sure to perform the configuration specified at 6 in "Restriction of the Status Monitor."
Déjà, la phase de préparation me pause problème.
libxml-1.8.17-xxx.i386.rpm
gtk+-1.2.xxx.i386.rpm
glib-1.2.xxx.i386.rpm
J'ai installé les paquet plus resent (à tord???)
Puis installé en premier
cnijfilter-common-2.70-1.i386.rpm (en installent chaque dépendances manquantes une par une)
Mais impossible d'installer le paquet
cnijfilter-ip1800series-2.70-1.i386 car des dépendances son requises :
[root@alice Téléchargements]# rpm -ivh cnijfilter-ip1800series-2.70-1.i386.rpm
erreur : Dépendances requises:
libpng.so.3 est nécessaire pour cnijfilter-ip1800series-2.70-1.i386
libtiff.so.3 est nécessaire pour cnijfilter-ip1800series-2.70-1.i386
J'ai tout de même essayé de l'installer sans les dépendances. Fedora reconnait l'imprimante mais aucune réaction quand je tante d'imprimer la page test.
Merci pour toute réponse :-D
