smartctl -a /dev/sda
smartctl 6.2 2014-07-16 r3952 [x86_64-linux-3.17.4-200.fc20.x86_64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA
Device Model: WDC WD2500BEVT-75A23T0
Serial Number: WD-WXN1E61ZNJA4
LU WWN Device Id: 5 0014ee 2b0e9a0ce
Firmware Version: 01.01A01
User Capacity: 250 059 350 016 bytes [250 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sun Dec 7 22:08:36 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 7080) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 73) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7037) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 153 145 021 Pre-fail Always - 1333
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1099
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 096 096 000 Old_age Always - 3040
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1072
191 G-Sense_Error_Rate 0x0032 001 001 000 Old_age Always - 173
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 78
193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always - 690277
194 Temperature_Celsius 0x0022 100 082 000 Old_age Always - 43
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
240 Head_Flying_Hours 0x0032 098 098 000 Old_age Always - 1753
241 Total_LBAs_Written 0x0032 200 200 000 Old_age Always - 3023526723
242 Total_LBAs_Read 0x0032 200 200 000 Old_age Always - 3229869231
254 Free_Fall_Sensor 0x0032 001 001 000 Old_age Always - 541
SMART Error Log Version: 1
ATA Error Count: 36426 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 36426 occurred at disk power-on lifetime: 3031 hours (126 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 08 02:41:36.650 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 02:41:36.648 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 02:41:36.648 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 02:41:36.647 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 02:41:36.646 IDENTIFY DEVICE
Error 36425 occurred at disk power-on lifetime: 3031 hours (126 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 08 02:41:36.648 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 02:41:36.647 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 02:41:36.646 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 08 02:41:36.635 SET FEATURES [Enable SATA feature]
Error 36424 occurred at disk power-on lifetime: 3031 hours (126 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 08 02:41:36.647 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 02:41:36.646 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 08 02:41:36.635 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 02:41:36.633 IDENTIFY DEVICE
Error 36423 occurred at disk power-on lifetime: 3031 hours (126 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 08 02:41:36.635 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 02:41:36.633 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 02:41:36.633 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 02:41:36.632 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 02:41:36.631 IDENTIFY DEVICE
Error 36422 occurred at disk power-on lifetime: 3031 hours (126 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 08 02:41:36.633 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 02:41:36.632 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 02:41:36.631 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 08 02:41:36.621 SET FEATURES [Enable SATA feature]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 1 -
# 2 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Je n'y comprend pas grand chose, mais j'ai l'impression que je vais être bon pour racheter un disque 🙁
Vous en pensez quoi?