Salut ! Merci encore pour vos réponses 🙂
Au fait, j'ai fait mon "yum update" mais j'ai toujours les mêmes erreurs : les modifications sur F20 posent des problèmes qd je repasse sur Windows.
nouvo09 wrote:Par acquit de conscience avant tout je ferais une analyse du disque avec smartctl. J'ai déjà vu renvoyer des disques neufs défectueux.
Pour faire un smartctl, j'ai fait un "yum install smartmontools"
Et après :
# smartctl -t short /dev/sda
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.10-200.fc20.x86_64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION ===
Sending command: "Execute SMART Short self-test routine immediately in off-line mode".
Drive command "Execute SMART Short self-test routine immediately in off-line mode" successful.
Testing has begun.
Please wait 2 minutes for test to complete.
Test will complete after Fri Apr 25 13:29:33 2014
Use smartctl -X to abort test.
Et le résultat :
# smartctl -a /dev/sda
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.10-200.fc20.x86_64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABD...
Device Model: TOSHIBA MQ01ABD100
Serial Number: 43AXT05JT
LU WWN Device Id: 5 000039 4b200117b
Firmware Version: AX0R2J
User Capacity: 1 000 204 886 016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Fri Apr 25 13:30:22 2014 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 243) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1713
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 586
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 096 096 000 Old_age Always - 1825
10 Spin_Retry_Count 0x0033 111 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 586
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 65
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 12
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 24410
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 34 (Min/Max 3/42)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
222 Loaded_Hours 0x0032 096 096 000 Old_age Always - 1620
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 268
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1825 -
# 2 Short offline Completed without error 00% 1825 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
J'ai oublié de préciser que je suis débutant sur Linux. Alors n'hésitez pas à me dire si j'ai mal fait un truc.
Là, a priori, je ne vois pas d'erreur. Après j'avais déjà fait ce genre de réparation sur Windows il y a 2 jours...
fgland wrote:
cela correspond exactement au problème du démarrage rapide de windows...
La question pourrait-être : comment s'assurer que windows est bien arrêté ?
@philippe_PMA : nos messages se sont croisés. Je rédigeais le mien quand tu as envoyé le tien...
Gérard
dans ton prmeier poste, tu parles de travail sous F20 depuis plusieurs semaines, c'était sans rebooter sur windows de temps en temps ?
le problème est récent ? si oui, y a-t-il eut une mise à jour de windows ? et cette mise à jour n'aurait-elle pas réactivé ce démarrage rapide ?
Gérard
J'ai bien l'impression d'avoir désactivé ce "fast boot" de Windows 8 (cf. mon post précédent).
Après, j'utilise bien l'option "Redémarrer", et j'ai quand même mes bugs de fichiers.
S'il y a une façon de s'assurer que Windows est bien éteint, je suis preneur !
Oui, c'est ça pendant 2 semaines, je n'ai jamais rebooté sur Windows. Et puis le jour où j'ai rebooté, j'ai eu quelques mises à jour Windows update, mais rien de majeur. La j'ai revérifié tous mes paramètres, tout semble OK.
C'est rageant comme problème..
J'ai fait le yum list ntfs* mtirabo :
$ yum list ntfs*
Modules complémentaires chargés : langpacks, refresh-packagekit
Dropbox/20/primary | 1.5 kB 00:00
Dropbox 4/4
adobe-linux-x86_64/primary | 1.2 kB 00:00
adobe-linux-x86_64 2/2
Paquets installés
ntfs-3g.x86_64 2:2014.2.15-1.fc20 @updates
ntfsprogs.x86_64 2:2014.2.15-1.fc20 @updates
Paquets disponibles
ntfs-3g.i686 2:2014.2.15-1.fc20 updates
ntfs-3g-devel.i686 2:2014.2.15-1.fc20 updates
ntfs-3g-devel.x86_64 2:2014.2.15-1.fc20 updates
Je vois qu'il y a des paquets disponible.. Ca vaut le coup de les installer ?
Merci pour vos réponse en tout cas 🙂
PS: un autre exemple de "bug" que j'ai : Là, je viens d'enregistrer deux photos reçues pas mail sur ma partition NTFS sous F20. Je reboot sur Windows et ces photos n'apparaissent nul part :/