Bonjour,

J'ai acheté cet onduleur : http://www.ldlc.com/fiche/PB00107876.html

J'aimerais tenter de le faire fonctionner sous Linux.

lsusb me retourne :

Bus 002 Device 002: ID 0001:0000 Fry's Electronics

après quelques recherche sur Internet, il semblerait qu'il utilise le protocle megatec qui est désormais repris dans le driver blazer, mais malheureusement cela ne fonctionne pas :

# blazer_usb -a monOnduleur -DDDDD -u root
Network UPS Tools - Megatec/Q1 protocol USB driver 0.03 (2.6.1)
   0.000000    debug level is '5'
   0.137556    Checking device (1D6B/0001) (005/001)
   0.137653    - VendorID: 1d6b
   0.137659    - ProductID: 0001
   0.137664    - Manufacturer: Linux 2.6.35.13-92.fc14.x86_64 uhci_hcd
   0.137669    - Product: UHCI Host Controller
   0.137673    - Serial Number: 0000:00:1d.3
   0.137678    - Bus: 005
   0.137682    Trying to match device
   0.137689    Device does not match - skipping
   0.137701    Checking device (1D6B/0001) (004/001)
   0.137728    - VendorID: 1d6b
   0.137734    - ProductID: 0001
   0.137738    - Manufacturer: Linux 2.6.35.13-92.fc14.x86_64 uhci_hcd
   0.137743    - Product: UHCI Host Controller
   0.137749    - Serial Number: 0000:00:1d.2
   0.137754    - Bus: 004
   0.137758    Trying to match device
   0.137763    Device does not match - skipping
   0.137772    Checking device (1D6B/0001) (003/001)
   0.137799    - VendorID: 1d6b
   0.137805    - ProductID: 0001
   0.137810    - Manufacturer: Linux 2.6.35.13-92.fc14.x86_64 uhci_hcd
   0.137815    - Product: UHCI Host Controller
   0.137819    - Serial Number: 0000:00:1d.1
   0.137824    - Bus: 003
   0.137828    Trying to match device
   0.137834    Device does not match - skipping
   0.137842    Checking device (0001/0000) (002/002)
   0.143573    - VendorID: 0001
   0.143601    - ProductID: 0000
   0.143612    - Manufacturer: unknown
   0.143622    - Product: unknown
   0.143632    - Serial Number: unknown
   0.143642    - Bus: 002
   0.143652    Trying to match device
   0.143664    Device matches
   0.146572    send_to_all: SETINFO ups.vendorid "0001"
   0.146597    send_to_all: SETINFO ups.productid "0000"
   0.146615    send_to_all: SETINFO device.type "ups"
   0.146630    send_to_all: SETINFO driver.version "2.6.1"
   0.146644    send_to_all: SETINFO driver.version.internal "0.03"
   0.146658    send_to_all: SETINFO driver.name "blazer_usb"
   0.146669    Trying megatec protocol...
   0.146681    send: Q1
   0.149563    read: error sending control message: Broken pipe
   0.152556    Stall condition cleared
   0.152581    blazer_status: short reply
   0.152587    Status read 1 failed
   0.152593    send: Q1
   0.155616    read: error sending control message: Broken pipe
   0.158572    Stall condition cleared
   0.158656    blazer_status: short reply
   0.158681    Status read 2 failed
   0.158693    send: Q1
   0.161622    read: error sending control message: Broken pipe
   0.166042    Stall condition cleared
   0.166099    blazer_status: short reply
   0.166107    Status read 3 failed
   0.166113    Trying mustek protocol...
   0.166119    send: QS
   0.166127    read: QS
   0.166166    blazer_status: short reply
   0.166171    Status read 1 failed
   0.166176    send: QS
   0.166180    read: QS
   0.166185    blazer_status: short reply
   0.166190    Status read 2 failed
   0.166194    send: QS
   0.166199    read: QS
   0.166203    blazer_status: short reply
   0.166208    Status read 3 failed
   0.166213    Trying megatec/old protocol...
   0.166218    send: D
   0.166222    read: D
   0.166227    blazer_status: short reply
   0.166231    Status read 1 failed
   0.166236    send: D
   0.166240    read: D
   0.166245    blazer_status: short reply
   0.166249    Status read 2 failed
   0.166254    send: D
   0.166259    read: D
   0.166263    blazer_status: short reply
   0.166268    Status read 3 failed
   0.166272    No supported UPS detected

Si vous avez une idée ou une méthode pour trouver le driver qui pourrait convenir ?

Et sinon, je me demande si cet onduleur ne fait pas du "serie over usb" et dans ce cas, il faudrait que j'arrive à créer un /dev/ttyUSB0 par exemple et que je teste avec un driver serie sous nut.
Mais je ne sais pas comment faire ?

Je vous remercie d'avance pour tout aide ou conseil.