smartctl --all /dev/sda
smartctl 5.39.1 2010-01-28 r3054 [x86_64-redhat-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen,
http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 5400.6 series
Device Model: ST9500325AS
Serial Number: 6VE5GGT4
Firmware Version: 0002SDM1
User Capacity: 500 107 862 016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Thu Aug 19 16:34:36 2010 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 138) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 083 081 006 Pre-fail Always - 221620345
3 Spin_Up_Time 0x0003 098 098 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 088 088 020 Old_age Always - 12341
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 072 060 030 Pre-fail Always - 16363952
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 761
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 037 020 Old_age Always - 784
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 9000
188 Command_Timeout 0x0032 099 099 000 Old_age Always - 13
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 065 050 045 Old_age Always - 35 (Lifetime Min/Max 33/36)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 17
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 087 087 000 Old_age Always - 27808
194 Temperature_Celsius 0x0022 035 050 000 Old_age Always - 35 (0 14 0 0)
195 Hardware_ECC_Recovered 0x001a 047 036 000 Old_age Always - 221620345
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 6
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 6
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 8868 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 8868 occurred at disk power-on lifetime: 761 hours (31 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 00:09:32.875 READ DMA EXT
27 00 00 00 00 00 e0 00 00:09:32.873 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:09:32.871 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:09:32.871 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:09:32.870 READ NATIVE MAX ADDRESS EXT
Error 8867 occurred at disk power-on lifetime: 761 hours (31 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 00:09:28.176 READ DMA EXT
27 00 00 00 00 00 e0 00 00:09:28.174 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:09:28.172 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:09:28.171 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:09:28.171 READ NATIVE MAX ADDRESS EXT
Error 8866 occurred at disk power-on lifetime: 761 hours (31 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 00:09:25.865 READ DMA EXT
27 00 00 00 00 00 e0 00 00:09:25.863 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:09:25.861 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:09:25.860 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:09:25.860 READ NATIVE MAX ADDRESS EXT
Error 8865 occurred at disk power-on lifetime: 761 hours (31 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 00:09:23.552 READ DMA EXT
27 00 00 00 00 00 e0 00 00:09:23.550 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:09:23.548 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:09:23.548 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:09:23.547 READ NATIVE MAX ADDRESS EXT
Error 8864 occurred at disk power-on lifetime: 761 hours (31 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 00:09:21.180 READ DMA EXT
27 00 00 00 00 00 e0 00 00:09:21.179 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:09:21.177 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:09:21.177 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:09:21.176 READ NATIVE MAX ADDRESS EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 760 976773167
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
