Salut Jean Michel
la configuration des périphériques est comme tu le préconises. le problème est que les noyaux 2.6 ne voient pas le hdd sur les controller raid alors que le raid PDC20376 LUI EST CORRECTEMENT RECONNU.
le module Libata est il configurable ?
Pourquoi depuis le kernel 2.6 ou le raid n'est plus matériel mais est géré de façon logiciel ?
Ma config est la suivante et sur xp, serveur 2003, mandrake 9.2 le disque branché seul sur le controller raid ne pose pas de probleme. parcontre avec un noyau 2.6 sur mandrake, Fedora, AUROX => même combat, ça ne marche pas (le disque est carrément pas reconnu).
Merci pour ton aide
Stan
voici un extrait du anaconda.syslog :
<7>libata version 1.02 loaded.
<7>sata_promise version 1.00
<6>ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 11 (level, low) -> IRQ 11
<6>ata1: SATA max UDMA/133 cmd 0xE0928200 ctl 0xE0928238 bmdma 0x0 irq 11
<6>ata2: SATA max UDMA/133 cmd 0xE0928280 ctl 0xE09282B8 bmdma 0x0 irq 11
<6>ata1: no device found (phy stat 00000000)
<6>scsi0 : sata_promise
<6>ata2: no device found (phy stat 00000000)
<6>scsi1 : sata_promise
la commande lsmod donne ceci :
[root@p2400 ~]# lsmod
Module Size Used by
mga 114244 2
parport_pc 24705 1
lp 11565 0
parport 41737 2 parport_pc,lp
md5 4033 1
ipv6 232577 12
autofs4 24005 0
sunrpc 160421 1
iptable_filter 2753 0
ip_tables 16193 1 iptable_filter
nls_cp850 4929 1
vfat 14785 1
fat 45409 1 vfat
ext3 116809 1
jbd 74969 1 ext3
pl2303 16325 0
usbserial 25513 1 pl2303
dm_mod 54741 0
button 6481 0
battery 8517 0
ac 4805 0
ohci1394 35033 0
ieee1394 302869 1 ohci1394
uhci_hcd 31449 0
ehci_hcd 31557 0
bttv 150541 0
video_buf 21701 1 bttv
i2c_algo_bit 8521 1 bttv
v4l2_common 5953 1 bttv
btcx_risc 4425 1 bttv
i2c_core 22081 2 bttv,i2c_algo_bit
videodev 9664 1 bttv
snd_usb_audio 59809 2
snd_usb_lib 12097 1 snd_usb_audio
snd_intel8x0 34829 2
snd_ac97_codec 64401 1 snd_intel8x0
snd_pcm_oss 47609 0
snd_mixer_oss 17217 3 snd_pcm_oss
snd_pcm 97993 3 snd_usb_audio,snd_intel8x0,snd_pcm_oss
snd_timer 29765 1 snd_pcm
snd_page_alloc 9673 2 snd_intel8x0,snd_pcm
gameport 4801 1 snd_intel8x0
snd_mpu401_uart 8769 1 snd_intel8x0
snd_rawmidi 26725 2 snd_usb_lib,snd_mpu401_uart
snd_seq_device 8137 1 snd_rawmidi
snd 54053 14 snd_usb_audio,snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore 9889 3 snd
tg3 85445 0
floppy 58609 0
sata_promise 9669 0
libata 40005 1 sata_promise
sd_mod 16961 0
scsi_mod 118417 3 sata_promise,libata,sd_mod
et dmesg :
[root@p2400 ~]# dmesg
Linux version 2.6.9-1.667 (
bhcompile@tweety.build.redhat.com) (gcc version 3.4.2 20041017 (Red Hat 3.4.2-6.fc3)) #1 Tue Nov 2 14:41:25 EST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009cc00 (usable)
BIOS-e820: 000000000009cc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffec000 (usable)
BIOS-e820: 000000001ffec000 - 000000001ffef000 (ACPI data)
BIOS-e820: 000000001ffef000 - 000000001ffff000 (reserved)
BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
zapping low mappings.
On node 0 totalpages: 131052
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126956 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ASUS ) @ 0x000f5360
ACPI: RSDT (v001 ASUS P4PE 0x42302e31 MSFT 0x31313031) @ 0x1ffec000
ACPI: FADT (v001 ASUS P4PE 0x42302e31 MSFT 0x31313031) @ 0x1ffec0bc
ACPI: T (v001 ASUS P4PE 0x42302e31 MSFT 0x31313031) @ 0x1ffec02c
ACPI: DSDT (v001 ASUS P4PE 0x00001000 MSFT 0x0100000b) @ 0x00000000
ACPI: PM-Timer IO Port: 0xe408
Built 1 zonelists
Kernel command line: BOOT_IMAGE=Fedora ro root=1605
mapped 4G/4G trampoline to ffff4000.
Initializing CPU#0
CPU 0 irqstacks, hard=023d5000 soft=023d4000
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 2406.270 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 515132k/524208k available (2068k kernel code, 8552k reserved, 647k data, 144k init, 0k highmem)
Calibrating delay loop... 4751.36 BogoMIPS (lpj=2375680)
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
There is already a security framework initialized, register_security failed.
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 3febfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: 3febf3ff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 04
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: IRQ9 SCI: Level Trigger.
checking if image is initramfs... it is
Freeing initrd memory: 381k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf1e60, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Enabled i801 SMBus device
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.PCI2._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9
ACPI: PCI interrupt 0000:00:1d.1
-> GSI 9 (level, low) -> IRQ 9
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 9
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 9 (level, low) -> IRQ 9
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 9 (level, low) -> IRQ 9
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:1f.3 -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:1f.5 -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:02:0b.0[A] -> GSI 11 (level, low) -> IRQ 11
apm: BIOS version 1.2 Flags 0x0b (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1116359612.954:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 6ECDA687281A73E5
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
vesafb: probe of vesafb0 failed with error -6
ACPI: Processor [CPU0] (supports C1)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 845G Chipset.
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 64M @ 0xf8000000
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 9 (level, low) -> IRQ 9
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: PLEXTOR DVDR PX-708A, ATAPI CD/DVD-ROM drive
hdb: IBM-DTLA-305020, ATA DISK drive
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: FUJITSU MPG3204AT E, ATA DISK drive
hdd: GoldStar CD-RW CED-8080B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hdb: max request size: 128KiB
hdb: 40188960 sectors (20576 MB) w/380KiB Cache, CHS=39870/16/63, UDMA(33)
hdb: cache flushes not supported
hdb: hdb1 hdb2 < hdb5 hdb6 > hdb3
hdc: max request size: 128KiB
hdc: 40031712 sectors (20496 MB) w/512KiB Cache, CHS=39714/16/63, UDMA(33)
hdc: cache flushes not supported
hdc: hdc1 hdc2 < hdc5 hdc6 >
hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: PS/2 Logitech Mouse on isa0060/serio1
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 9362)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S3 S4 S5)
ACPI wakeup devices:
PCI0 PCI1 PCI2 UAR1 USB0 USB1 USB2 US20 AC97
Freeing unused kernel memory: 144k freed
SCSI subsystem initialized
libata version 1.02 loaded.
sata_promise version 1.00
ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 11 (level, low) -> IRQ 11
ata1: SATA max UDMA/133 cmd 0x2281E200 ctl 0x2281E238 bmdma 0x0 irq 11
ata2: SATA max UDMA/133 cmd 0x2281E280 ctl 0x2281E2B8 bmdma 0x0 irq 11
ata1: no device found (phy stat 00000000)
scsi0 : sata_promise
ata2: no device found (phy stat 00000000)
scsi1 : sata_promise
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
inserting floppy driver for 2.6.9-1.667
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
tg3.c:v3.10 (September 14, 2004)
PCI: Enabling device 0000:02:05.0 (0014 -> 0016)
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 10 (level, low) -> IRQ 10
divert: allocating divert_blk for eth0
eth0: Tigon3 [partno(BCM95702A20) rev 1002 PHY(5703)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:e0:18:b4:65:38
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
PCI: Enabling device 0000:00:1f.5 (0004 -> 0007)
ACPI: PCI interrupt 0000:00:1f.5 -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.5 to 64
AC'97 0 analog subsections not ready
intel8x0_measure_ac97_clock: measured 49388 usecs
intel8x0: clocking to 48000
usbcore: registered new driver snd-usb-audio
hw_random: RNG not detected
Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
PCI: Enabling device 0000:02:0b.0 (0004 -> 0006)
ACPI: PCI interrupt 0000:02:0b.0[A] -> GSI 11 (level, low) -> IRQ 11
bttv0: Bt849 (rev 18) at 0000:02:0b.0, irq: 11, latency: 32, mmio: 0xf5000000
bttv0: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00107fff [init]
bttv: readee error
bttv0: using tuner=-1
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: registered device video0
bttv0: registered device vbi0
PCI: Enabling device 0000:00:1d.7 (0004 -> 0006)
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 11, pci mem 2293c000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:1d.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 5, io base 0000d800
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1 -> GSI 9 (level, low) -> IRQ 9
uhci_hcd 0000:00:1d.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 9, io base 0000d400
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 9 (level, low) -> IRQ 9
uhci_hcd 0000:00:1d.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 9, io base 0000d000
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
PCI: Enabling device 0000:02:03.0 (0094 -> 0097)
ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 11 (level, low) -> IRQ 11
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[f3000000-f30007ff] Max Packet=[2048]
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
usb 2-2: new full speed USB device using address 2
usb 3-1: new full speed USB device using address 2
ACPI: Power Button (FF) [PWRF]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e01800000a6f45]
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial_generic
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for PL-2303
pl2303 3-1:1.0: PL-2303 converter detected
usb 3-1: PL-2303 converter now attached to ttyUSB0
usbcore: registered new driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver v0.11
cdrom: open failed.
cdrom: open failed.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Adding 1269092k swap on /dev/hdb5. Priority:-1 extents:1
Adding 827308k swap on /dev/hdc6. Priority:-2 extents:1
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
ip_tables: (C) 2000-2002 Netfilter core team
NET: Registered protocol family 10
Disabled Privacy Extensions on device 02369a00(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
eth0: no IPv6 routers present
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 5 (level, low) -> IRQ 5
[drm] Initialized mga 3.1.0 20021029 on minor 0:
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
eth0: no IPv6 routers present
Tes idées sont les bien venues
Merci
