Ma config : fedora core 3 x86_64, proc amd64 3200, mobo asus K8N-E Deluxe, carte ethernet Realtek 8139, FAI Club-Internet, modem routeur Comtrend CT 633 relié à l'ordi par RJ45.
-----------------------
Voici maintenant ce que me renvoie ifconfg :
-----------------------
[pierre@localhost ~]$ ifconfig
eth0 Lien encap:Ethernet HWaddr 00:E0:4C:03:32:BD
inet adr:192.168.1.3 Bcast:192.168.1.255 Masque:255.255.255.0
adr inet6: fe80::2e0:4cff:fe03:32bd/64 Scope:Lien
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:162 errors:0 dropped:0 overruns:0 frame:0
TX packets:173 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:164591 (160.7 KiB) TX bytes:23935 (23.3 KiB)
Interruption:177 Adresse de base:0xd800
lo Lien encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:3397 errors:0 dropped:0 overruns:0 frame:0
TX packets:3397 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:5392804 (5.1 MiB) TX bytes:5392804 (5.1 MiB)
_________________________
Et voici ce que me renvoit dmesg :
_________________________
[pierre@localhost ~]$ dmesg
Bootdata ok (command line is ro root=LABEL=/ rhgb quiet)
Linux version 2.6.10-1.766_FC3 (
bhcompile@crowe.devel.redhat.com) (gcc version 3.4.2 20041017 (Red Hat 3.4.2-6.fc3)) #1 Wed Feb 9 23:05:01 EST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffc0000 (usable)
BIOS-e820: 000000001ffc0000 - 000000001ffd0000 (ACPI data)
BIOS-e820: 000000001ffd0000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
No mptable found.
On node 0 totalpages: 131008
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126912 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
Nvidia board detected. Ignoring ACPI timer override.
ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000f9e20
ACPI: RSDT (v001 A M I OEMRSDT 0x10000404 MSFT 0x00000097) @ 0x000000001ffc0000
ACPI: FADT (v002 A M I OEMFACP 0x10000404 MSFT 0x00000097) @ 0x000000001ffc0200
ACPI: MADT (v001 A M I OEMAPIC 0x10000404 MSFT 0x00000097) @ 0x000000001ffc0390
ACPI: OEMB (v001 A M I OEMBIOS 0x10000404 MSFT 0x00000097) @ 0x000000001ffd0040
ACPI: DSDT (v001 A0055 A0055003 0x00000003 INTL 0x02002026) @ 0x0000000000000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Checking aperture...
CPU 0: aperture @ f0000000 size 128 MB
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet console=tty0
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 65536 bytes)
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 2210.783 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 509288k/524032k available (2362k kernel code, 14116k reserved, 1268k data, 176k init)
Calibrating delay loop... 4374.52 BogoMIPS (lpj=2187264)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 00
Using local APIC NMI watchdog using perfctr0
Using local APIC timer interrupts.
Detected 12.561 MHz APIC timer.
checking if image is initramfs... it is
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.P0P1._PRT]
ACPI: Power Resource [ISAV] (on)
ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *9
ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *10
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *11
ACPI: PCI Interrupt Link [LKLN] (IRQs 20 21 22) *9
ACPI: PCI Interrupt Link [LAUI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LKMO] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LKSM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LTIE] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22) *14
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to
bjorn.helgaas@hp.com
** so I can fix the driver.
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 128M @ 0xf0000000
PCI-DMA: Disabling IOMMU.
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1109690515.651:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key FDDE7E175542E38
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
NFORCE3-250: chipset revision 162
NFORCE3-250: not 100% native mode: will probe irqs later
NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: WDC WD1600JB-00GVA0, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: SAMSUNG CD-R/RW DRIVE SW-252F, ATAPI CD/DVD-ROM drive
hdd: Pioneer DVD-ROM ATAPIModel DVD-121 0102, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(33)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
hdc: ATAPI 1X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X DVD-ROM drive, 256kB Cache, UDMA(66)
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: PS2++ Logitech Wheel Mouse on isa0060/serio1
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 28Kbytes
TCP: Hash tables configured (established 32768 bind 4681)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.00.09e)
powernow-k8: 0 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xa (1300 mV)
powernow-k8: 2 : fid 0xc (2000 MHz), vid 0x6 (1400 mV)
powernow-k8: 3 : fid 0xe (2200 MHz), vid 0x2 (1500 mV)
cpu_init done, current fid 0xe, vid 0x0
powernow-k8: ph2 null fid transition 0xe
ACPI wakeup devices:
PS2K PS2M UAR1 UAR2 USB0 MAC USB1 USB2 P0P1
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 176k freed
SCSI subsystem initialized
libata version 1.10 loaded.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 19
ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 19 (level, low) -> IRQ 177
divert: allocating divert_blk for eth0
eth0: RealTek RTL8139 at 0xd800, 00:e0:4c:03:32:bd, IRQ 177
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 18
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 18 (level, low) -> IRQ 185
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 22
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 22 (level, low) -> IRQ 193
ehci_hcd 0000:00:02.2: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 193, pci mem 0xfebffc00
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 21
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 21 (level, low) -> IRQ 201
ohci_hcd 0000:00:02.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 201, pci mem 0xfebfd000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 20
ACPI: PCI interrupt 0000:00:02.1
-> GSI 20 (level, low) -> IRQ 209
ohci_hcd 0000:00:02.1: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: irq 209, pci mem 0xfebfe000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ACPI: PCI interrupt 0000:02:0b.0[A] -> GSI 18 (level, low) -> IRQ 185
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[185] MMIO=[feaff000-feaff7ff] Max Packet=[2048]
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
ACPI: Power Button (FF) [PWRF]
ibm_acpi: ec object not found
EXT3 FS on hda1, internal journal
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel@redhat.com
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e0180000b04582]
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff80448560(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 17
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 17 (level, low) -> IRQ 217
NVRM: loading NVIDIA Linux x86_64 NVIDIA Kernel Module 1.0-6629 Wed Nov 3 11:43:48 PST 2004
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
Adding 2048248k swap on /dev/hda5. Priority:-1 extents:1
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
eth0: no IPv6 routers present
i2c /dev entries driver
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
ip_tables: (C) 2000-2002 Netfilter core team
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
eth0: no IPv6 routers present
_________________________
Voici donc toutes les infos relatives au problème de ma config internet.
