j ai pas l impression que fglrx.ko soit un lien :
[root@localhost 2.6.x]# ls -l fglrx.ko
-rw-r--r-- 1 root root 1090763 mar 24 17:00 fglrx.ko
[root@localhost 2.6.x]#
et dmesg:
[root@localhost 2.6.x]# dmesg
OVR (bus 0 bus_irq 0 global_irq 2 dfl edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 22 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
CPU 0 irqstacks, hard=c03d2000 soft=c03b2000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1403.308 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 774112k/786352k available (1790k kernel code, 11704k reserved, 736k data, 208k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 2768.89 BogoMIPS (lpj=1384448)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebf3ff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
per-CPU timeslice cutoff: 1462.73 usecs.
task migration cache decay timeout: 2 msecs.
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c03d3000 soft=c03b3000
Initializing CPU#1
Calibrating delay loop... 2801.66 BogoMIPS (lpj=1400832)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebf3ff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Total of 2 processors activated (5570.56 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 194k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf1e50, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 *6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Enabled i801 SMBus device
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.PCI2._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to
bjorn.helgaas@hp.com
** so I can fix the driver.
pnp: 00:01: ioport range 0xe400-0xe47f could not be reserved
pnp: 00:01: ioport range 0xe800-0xe81f has been reserved
pnp: 00:01: ioport range 0xec00-0xec3f has been reserved
pnp: 00:01: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:0d: ioport range 0x3f0-0x3f1 has been reserved
Simple Boot Flag at 0x3a set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
audit(1111918894.854:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key D88FE3902ABCF223
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 845G Chipset.
agpgart: Maximum main memory to use for agp memory: 690M
agpgart: AGP aperture is 64M @ 0xf8000000
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 177
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 4R080L0, ATA DISK drive
hdb: MAXTOR 6L020J1, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-STDVD-ROM GDR8161B, ATAPI CD/DVD-ROM drive
hdd: _NEC DVD_RW ND-3520A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
PDC20269: IDE controller at PCI slot 0000:02:0a.0
ACPI: PCI interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 169
PDC20269: chipset revision 2
PDC20269: 100% native mode on irq 169
ide2: BM-DMA at 0x9400-0x9407, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0x9408-0x940f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
hde: ST380011A, ATA DISK drive
ide2 at 0xa800-0xa807,0xa402 on irq 169
Probing IDE interface ide3...
Probing IDE interface ide3...
hda: max request size: 128KiB
hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2
hdb: max request size: 128KiB
hdb: 40132503 sectors (20547 MB) w/1819KiB Cache, CHS=39813/16/63, UDMA(100)
hdb: cache flushes supported
hdb: hdb1 hdb2 hdb3
hde: max request size: 1024KiB
hde: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hde: cache flushes supported
hde: hde1
hdc: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio1
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 64Kbytes
TCP: Hash tables configured (established 131072 bind 43690)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI wakeup devices:
PCI0 PCI1 PCI2 UAR1 USB0 USB1 USB2 US20 AC97
ACPI: (supports S0 S1 S4 S5)
CPU0:
domain 0: span 00000003
groups: 00000001 00000002
domain 1: span 00000003
groups: 00000003
CPU1:
domain 0: span 00000003
groups: 00000002 00000001
domain 1: span 00000003
groups: 00000003
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 208k freed
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0330380(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
ACPI: Power Button (FF) [PWRF]
ibm_acpi: ec object not found
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 185
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 185, pci mem 0xde000000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 193
uhci_hcd 0000:00:1d.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 193, io base 0xb800
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1
-> GSI 19 (level, low) -> IRQ 201
uhci_hcd 0000:00:1d.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 201, io base 0xb400
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 177
uhci_hcd 0000:00:1d.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 177, io base 0xb000
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 3-2: new low speed USB device using uhci_hcd and address 2
input: USB HID v1.10 Joystick [Mega World USB Game Controllers] on usb-0000:00:1d.1-2
EXT3 FS on hdb2, internal journal
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel@redhat.com
Adding 1566328k swap on /dev/hdb3. Priority:-1 extents:1
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
microcode: CPU0 updated from revision 0x17 to 0x2e, date = 08112004
microcode: CPU1 updated from revision 0x17 to 0x2e, date = 08112004
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
Trying to free free DMA3
pnp: Device 00:07 disabled.
SCSI subsystem initialized
floppy0: no floppy controllers found
ieee1394: Initialized config rom entry `ip1394'
b44.c:v0.95 (Aug 3, 2004)
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 20 (level, low) -> IRQ 209
divert: allocating divert_blk for eth0
eth0: Broadcom 4400 10/100BaseT Ethernet 00:0c:6e:a7:9c:5d
divert: freeing divert_blk for eth0
ip_tables: (C) 2000-2002 Netfilter core team
b44.c:v0.95 (Aug 3, 2004)
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 20 (level, low) -> IRQ 209
divert: allocating divert_blk for eth0
eth0: Broadcom 4400 10/100BaseT Ethernet 00:0c:6e:a7:9c:5d
Bluetooth: Core ver 2.7
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.6
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.3
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
pnp: Device 00:07 activated.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
lp0: console ready
ACPI: PCI interrupt 0000:00:1f.5 -> GSI 17 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49305 usecs
intel8x0: clocking to 48000
usb 2-1: new full speed USB device using uhci_hcd and address 2
[eagle-usb] driver V2 loaded
[eagle-usb] New pre-firmware modem detected
[eagle-usb] Uploading firmware..
[eagle-usb] Binding eu_instance_t to USB 002/002
usbcore: registered new driver eagle-usb
usb 2-1: USB disconnect, address 2
[eagle-usb] Pre-firmware modem removed
usb 2-1: new full speed USB device using uhci_hcd and address 3
[eagle-usb] New USB ADSL device detected, waiting for DSP code...
[eagle-usb] Interface 0 accepted.
[eagle-usb] created proc entry at : /proc/driver/eagle-usb/002-003
[eagle-usb] ioctl EU_IO_OPTIONS received
[eagle-usb] ioctl EU_IO_DSP received
[eagle-usb] Loading DSP code to device...
[eagle-usb] DSP code successfully loaded to device
[eagle-usb] Modem operational !!
divert: allocating divert_blk for eth1
[eagle-usb] Ethernet device eth1 created.
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
eth1: no IPv6 routers present
ip_tables: (C) 2000-2002 Netfilter core team
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
divert: not allocating divert_blk for non-ethernet device ppp0
kjournald starting. Commit interval 5 seconds
EXT3 FS on hde1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
application firefox-bin uses obsolete OSS audio interface
application sox uses obsolete OSS audio interface
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 679 MBytes.
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 193
[fglrx] module loaded - fglrx 8.10.19 [Feb 9 2005] on minor 0
[fglrx] module unloaded - fglrx 8.10.19 [Feb 9 2005] on minor 0
[root@localhost 2.6.x]#