Bonjour à tous,
Je suis tout nouveau sur linux et je voudrais utiliser Fedora 8. J'ai vue qu'il y avait beaucoup de sujet concernant les probléme en wifi mais je n'ai pas réussi à résoudre mon probléme...
Alors voilà j'ai une carte D-Link DWL-G520, c'est une carte PCI pour conexion wifi. Le probléme est que je n'arrive pas à activer les wifi sous Fedora, alors si quelqu'un peut m'aider, sa serait genti.
Dans #lsusb
Bus 005 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
Bus 006 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 004 Device 002: ID 10d6:1100 Actions Semiconductor Co., Ltd MPMan MP-Ki 128 MP3 Player/Recorder
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 002: ID 05a9:4519 OmniVision Technologies, Inc.
Bus 003 Device 003: ID 045e:0039 Microsoft Corp. IntelliMouse Optical
Bus 003 Device 001: ID 0000:0000
Dans #dmesg
[root@localhost ~]# dmesg
Linux version 2.6.23.1-42.fc8 (kojibuilder@xenbuilder4.fedora.phx.redhat.com) (gcc version 4.1.2 20070925 (Red Hat 4.1.2-33)) #1 SMP Tue Oct 30 13:55:12 EDT 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fee0000 (usable)
BIOS-e820: 000000007fee0000 - 000000007fee3000 (ACPI NVS)
BIOS-e820: 000000007fee3000 - 000000007fef0000 (ACPI data)
BIOS-e820: 000000007fef0000 - 000000007ff00000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
1150MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f6530
Using x86 segment limits to approximate NX protection
Entering add_active_range(0, 0, 524000) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 524000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 524000
On node 0 totalpages: 524000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 2301 pages used for memmap
HighMem zone: 292323 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
DMI 2.4 present.
Using APIC driver default
ACPI: RSDP 000F81D0, 0024 (r2 ATI )
ACPI: XSDT 7FEE3100, 004C (r1 ATI ASUSACPI 42302E31 AWRD 0)
ACPI: FACP 7FEE84C0, 00F4 (r3 ATI ASUSACPI 42302E31 AWRD 0)
ACPI: DSDT 7FEE3280, 51EC (r1 ATI ASUSACPI 1000 MSFT 3000000)
ACPI: FACS 7FEE0000, 0040
ACPI: SSDT 7FEE86C0, 0248 (r1 PTLTD POWERNOW 1 LTP 1)
ACPI: HPET 7FEE8980, 0038 (r1 ATI ASUSACPI 42302E31 AWRD 98)
ACPI: MCFG 7FEE8A00, 003C (r1 ATI ASUSACPI 42302E31 AWRD 0)
ACPI: APIC 7FEE8600, 0068 (r1 ATI ASUSACPI 42302E31 AWRD 0)
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:11 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:11 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x8200 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 80000000 (gap: 7ff00000:60100000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
Built 1 zonelists in Zone order. Total pages: 519907
Kernel command line: ro root=LABEL=/ rhgb quiet
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c07a8000 soft=c0788000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2300.107 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2070148k/2096000k available (2183k kernel code, 24636k reserved, 1117k data, 280k init, 1178496k highmem)
virtual kernel memory layout:
fixmap : 0xffc53000 - 0xfffff000 (3760 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc073f000 - 0xc0785000 ( 280 kB)
.data : 0xc0621f7d - 0xc0739544 (1117 kB)
.text : 0xc0400000 - 0xc0621f7d (2183 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
hpet clockevent registered
Calibrating delay using timer specific routine.. 4602.55 BogoMIPS (lpj=2301278)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000011f 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0(2) -> Core 0
CPU: After all inits, caps: 178bf3ff ebd3fbff 00000000 00000410 00002001 00000000 0000011f 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ stepping 01
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c07a9000 soft=c0789000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4599.83 BogoMIPS (lpj=2299917)
CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000011f 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 1(2) -> Core 1
CPU: After all inits, caps: 178bf3ff ebd3fbff 00000000 00000410 00002001 00000000 0000011f 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ stepping 01
Total of 2 processors activated (9202.39 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 2 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=336 bytes
sizeof(dentry)=132 bytes
sizeof(ext3inode)=488 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=180 bytes
sizeof(task_struct)=1552 bytes
Booting paravirtualized kernel on bare hardware
Time: 23:26:23 Date: 03/25/08
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: PCI BIOS revision 3.00 entry at 0xf1e40, last bus=3
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE7._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
hpet0: 4 32-bit timers, 14318180 Hz
Time: hpet clocksource has been installed.
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
pnp: 00:01: ioport range 0x4100-0x411f has been reserved
pnp: 00:01: ioport range 0x228-0x22f has been reserved
pnp: 00:01: ioport range 0x40b-0x40b has been reserved
pnp: 00:01: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:01: ioport range 0xc00-0xc01 has been reserved
pnp: 00:01: ioport range 0xc14-0xc14 has been reserved
pnp: 00:01: ioport range 0xc50-0xc52 has been reserved
pnp: 00:01: ioport range 0xc6c-0xc6d has been reserved
pnp: 00:0b: iomem range 0xe0000000-0xefffffff could not be reserved
pnp: 00:0c: iomem range 0xcd000-0xcffff has been reserved
pnp: 00:0c: iomem range 0xf0000-0xf7fff could not be reserved
pnp: 00:0c: iomem range 0xf8000-0xfbfff could not be reserved
pnp: 00:0c: iomem range 0xfc000-0xfffff could not be reserved
PCI: Bridge: 0000:00:02.0
IO window: d000-dfff
MEM window: f8000000-fbffffff
PREFETCH window: d0000000-dfffffff
PCI: Bridge: 0000:00:07.0
IO window: e000-efff
MEM window: fdd00000-fddfffff
PREFETCH window: fdc00000-fdcfffff
PCI: Bridge: 0000:00:14.4
IO window: c000-cfff
MEM window: fdf00000-fdffffff
PREFETCH window: fde00000-fdefffff
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Setting latency timer of device 0000:00:07.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2912k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
audit(1206487582.534:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
ksign: Installing public key data
Loading keyring
- Added public key 230FF4508E76ABC1
- User ID: Red Hat, Inc. (Kernel Module GPG key)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: MSI quirk detected. MSI deactivated.
Boot video device is 0000:01:00.0
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
PCI: Setting latency timer of device 0000:00:07.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:07.0:pcie00]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (40 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ processors (2 cpu cores) (version 2.00.00)
powernow-k8: 0 : fid 0xf (2300 MHz), vid 0xa
powernow-k8: 1 : fid 0xe (2200 MHz), vid 0xb
powernow-k8: 2 : fid 0xc (2000 MHz), vid 0xd
powernow-k8: 3 : fid 0xa (1800 MHz), vid 0xf
powernow-k8: 4 : fid 0x2 (1000 MHz), vid 0x12
Using IPI No-Shortcut mode
Magic number: 0:675:454
Freeing unused kernel memory: 280k freed
Write protecting the kernel read-only data: 849k
ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 16
ehci_hcd 0000:00:13.5: EHCI Host Controller
ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.5: debug port 1
ehci_hcd 0000:00:13.5: irq 16, io mem 0xfe029000
ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 17, io mem 0xfe02e000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.1[b] -> GSI 17 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 18, io mem 0xfe02d000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.2: OHCI Host Controller
ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:13.2: irq 19, io mem 0xfe02c000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.3[b] -> GSI 17 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.3: OHCI Host Controller
ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.3: irq 18, io mem 0xfe02b000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.4: OHCI Host Controller
ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6
ohci_hcd 0000:00:13.4: irq 19, io mem 0xfe02a000
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
usb 3-1: new full speed USB device using ohci_hcd and address 2
SCSI subsystem initialized
libata version 2.21 loaded.
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17
scsi0 : pata_atiixp
scsi1 : pata_atiixp
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001f900 irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001f908 irq 15
usb 3-1: configuration #1 chosen from 1 choice
ata1.00: ATA-6: ST3160023A, 8.01, max UDMA/100
ata1.00: 312581808 sectors, multi 1: LBA48
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA ST3160023A 8.01 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 <<6>usb 3-2: new low speed USB device using ohci_hcd and address 3
sda5 sda6 sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
usb 3-2: configuration #1 chosen from 1 choice
input: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM) as /class/input/input2
input: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:13.1-2
usb 4-2: new full speed USB device using ohci_hcd and address 2
usb 4-2: configuration #1 chosen from 1 choice
ahci 0000:00:12.0: version 2.3
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 20
ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pmp pio slum part
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata3: SATA max UDMA/133 cmd 0xf8842100 ctl 0x00000000 bmdma 0x00000000 irq 20
ata4: SATA max UDMA/133 cmd 0xf8842180 ctl 0x00000000 bmdma 0x00000000 irq 20
ata5: SATA max UDMA/133 cmd 0xf8842200 ctl 0x00000000 bmdma 0x00000000 irq 20
ata6: SATA max UDMA/133 cmd 0xf8842280 ctl 0x00000000 bmdma 0x00000000 irq 20
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATAPI: HL-DT-ST DVDRAM GSA-H66N, CB00, max UDMA/100
ata3.00: configured for UDMA/100
ata4: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
scsi 2:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-H66N CB00 PQ: 0 ANSI: 5
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
security: 8 users, 11 roles, 2317 types, 112 bools, 1 sens, 1024 cats
security: 67 classes, 207815 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev sda7, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), uses genfs_contexts
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1206487593.721:2): policy loaded auid=4294967295
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 2:0:0:0: Attached scsi generic sg1 type 5
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 19 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth0: RTL8168b/8111b at 0xf8844000, 00:1b:fc:8b:39:84, XID 38000000 IRQ 16
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
Initializing USB Mass Storage driver...
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
parport_pc 00:09: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
ACPI: PCI Interrupt 0000:03:07.0[A] -> GSI 22 (level, low) -> IRQ 20
firewire_ohci: Added fw-ohci device 0000:03:07.0, OHCI version 1.10
ACPI: PCI Interrupt 0000:03:06.0[A] -> GSI 21 (level, low) -> IRQ 21
phy0: Selected rate control algorithm 'simple'
ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 17
ath_pci 0000:03:06.0: AR5212 chip found: mac 7.7 phy 4.5
usbcore: registered new interface driver snd-usb-audio
firewire_core: created new fw device fw0 (0 config rom retries, S400)
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 19
usb-storage: device scan complete
scsi scan: INQUIRY result too short (5), using 36
scsi 6:0:0:0: Direct-Access GENERIC USB DISK DEVICE 1.00 PQ: 0 ANSI: 0 CCS
sd 6:0:0:0: [sdb] 3997169 512-byte hardware sectors (2047 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 00 c0 00 00
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sd 6:0:0:0: [sdb] 3997169 512-byte hardware sectors (2047 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 00 c0 00 00
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sdb: unknown partition table
sd 6:0:0:0: [sdb] Attached SCSI removable disk
sd 6:0:0:0: Attached scsi generic sg2 type 0
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
device-mapper: multipath: version 1.0.5 loaded
loop: module loaded
EXT3 FS on sda7, internal journal
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
Clocksource tsc unstable (delta = -108448035 ns)
unable to reset hardware: -22
ath_chan_set: unable to reset channel 11 (2462 Mhz)
unable to reset hardware: -22
audit(1206484010.855:3): audit_pid=1738 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
r8169: eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
unable to reset hardware: -22
unable to reset hardware: -22
hda-intel: Invalid position buffer, using LPIB read method instead.
fuse init (API version 7.8)
SELinux: initialized (dev sda5, type fuseblk), uses genfs_contexts
SELinux: initialized (dev sda6, type fuseblk), uses genfs_contexts
SELinux: initialized (dev sda1, type fuseblk), uses genfs_contexts
SELinux: initialized (dev sdb, type vfat), uses genfs_contexts
Dans # lsmod
[root@localhost ~]# lsmod
Module Size Used by
vfat 13249 1
fat 45277 1 vfat
fuse 38485 6
rfcomm 36825 0
l2cap 25537 9 rfcomm
bluetooth 49316 4 rfcomm,l2cap
autofs4 20421 2
sunrpc 140765 1
cpufreq_ondemand 10317 1
loop 16581 0
dm_mirror 21697 0
dm_multipath 18249 0
dm_mod 46465 2 dm_mirror,dm_multipath
ipv6 245989 14
snd_usb_audio 75329 0
arc4 5953 2
ecb 6721 2
blkcipher 9029 1 ecb
snd_hda_intel 274657 2
snd_seq_dummy 6725 0
rc80211_simple 7361 1
snd_seq_oss 29889 0
snd_seq_midi_event 9793 1 snd_seq_oss
snd_seq 44849 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_pcm_oss 37569 0
snd_mixer_oss 16705 1 snd_pcm_oss
snd_pcm 63685 3 snd_usb_audio,snd_hda_intel,snd_pcm_oss
ath5k 85197 0
firewire_ohci 18113 0
mac80211 131409 2 rc80211_simple,ath5k
firewire_core 36097 1 firewire_ohci
snd_usb_lib 17345 1 snd_usb_audio
snd_timer 20549 2 snd_seq,snd_pcm
parport_pc 26981 0
snd_page_alloc 11337 2 snd_hda_intel,snd_pcm
cfg80211 10441 1 mac80211
parport 32393 1 parport_pc
crc_itu_t 6081 1 firewire_core
snd_rawmidi 21185 1 snd_usb_lib
snd_seq_device 10061 4 snd_seq_dummy,snd_seq_oss,snd_seq,snd_rawmidi
snd_hwdep 10309 2 snd_usb_audio,snd_hda_intel
snd 43461 15 snd_usb_audio,snd_hda_intel,snd_seq_oss,snd_seq,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_rawmidi,snd_seq_device,snd_hwdep
usb_storage 73345 1
k8temp 8257 0
i2c_piix4 11341 0
soundcore 9633 1 snd
hwmon 6469 1 k8temp
i2c_core 21825 1 i2c_piix4
r8169 27589 0
button 10321 0
sg 31965 0
sr_mod 17509 0
cdrom 33889 1 sr_mod
ahci 22597 0
pata_atiixp 9409 4
ata_generic 8901 0
libata 99633 3 ahci,pata_atiixp,ata_generic
sd_mod 27329 6
scsi_mod 119757 5 usb_storage,sg,sr_mod,libata,sd_mod
ext3 110665 1
jbd 52457 1 ext3
mbcache 10177 1 ext3
uhci_hcd 23633 0
ohci_hcd 21445 0
ehci_hcd 31693 0
Donc voilà si quelqu'un peut m'aider...
Merci d'avance.
