Bonsoir,

T'as encore une RH-7.3 qui tourne ? Chapeau ! Ça me rappelle de vieux souvenirs...
Je te sens un peu négatif dans l'ensemble, mais quand ça marche pas, je sais ce que c'est; faut se détendre et faire un peu de rtfm...

Je comprend pas ce qui te gène avec la police du bureau, moi je suis toujours sous fc5/kde sans avoir rien touché niveau police, c'est très lisible; avec fc6 je ne sais pas mais sinon ça doit bien se configurer quelque part.

Pour les outils de configuration, si tu veux savoir tout ce qui est disponible, je pense que le mieux c'est, avec une console root, de taper "system" puis d'appuyer sur la touche TAB plusieurs fois jusqu'à ce que ça affiche tous les scripts de configuration, il me semble qu'il y en a une ou deux dizaines, à la louche.

Pour le sagem fast 800 usb, j'avais un peu / pas mal bataillé à l'époque pour le faire fonctionner (sur une 7.3 justement je crois), c'est sur que c'est pas le modem que je recommanderai, mais bon si tu n'as que ça sous la main. En faisant une recherche sur ce site avec "sagem 800", on voit plein de fils de discussion, j'imagine que tu en as parcouru quelques uns, il y a surement des personnes qui ont eu le même problème que toi et qui sont arrivés à le résoudre; c'est ça qui est bien avec ce forum, c'est qu'on peut profiter de l'expérience des autres.

J'imagine que tu as fait cette recherche... ? Si oui et que tu n'as rien trouvé, désolé, je ne peux pas t'aider plus, ça fait longtemps que je n'utilise plus ce modem et je n'en suis pas un expert; je peux juste répéter une base du débugage : ouvrir une console root, taper :
tail -f /var/log/messages
essayer d'initialiser le modem, puis une connexion et voir si la console ne hurle pas des erreurs.

Pareil pour ton disque dur usb externe, moi je n'en n'ai pas, mais j'imagine qu'il y a plein de gens sur ce forum qui en ont et qui sont arrivé à les faire marcher, donc à mon avis la solution à ton problème est dans ce forum, faut juste chercher un peu.

Ha, si tu n'as jamais utilisé la fonction recherche ici, c'est la case de saisie blanche en haut à droite...

Sinon, ce n'est pas moi qui vais te dire d'utiliser telle ou telle distribution, tu es libre et c'est très bien ainsi, je pense juste que fedora peut te donner entière satisfaction, à condition de se documenter un peu, mais si tu as commencé avec la RH-5.1, tu devrais quand même avoir de bonnes bases depuis le temps.

Dernière chose, je n'ai jamais fait de mise à jour d'une version de fedora à une autre, je sauvegarde toujours mes données, je formate le disque et je reinstalle. Ça prend sans doute plus de temps à tout reinstaller et reconfigurer, mais je pense que ça permet de passer à coté de certains problèmes; cependant ceci est juste une superstition personnelle et non un retour d'expérience.

Bon courage, et pas de découragement sans avoir cherché un peu... 😉
hum...
J'ai aussi commence avec redhat 5.1 jusqu'a FC 6 !
Si tel est ton cas, tu devrais avoir un peu l'habitude...
Et puis, c'est pas avec un "retenez-moi ou alors je me barre" que tu auras de l'aide. Ca fait chantage...

Maintenant pour tes petits problemes :
- le modem ueagle : suis le tuto...en cas de probleme renvoie le resultat de :
# dmesg
- l'affichage. C'est quoi ta CG ? Tu n'as peut etre pas le bon pilote.
- le DD USB. Branche le. Que te renvoie alors :
# fdisk -l

++
Bonsoir,

Comme tu le dis, le coté négatif arrive au bout de quelques dizaines d'heures sans amélioration, c'est dur. Je vais attendre encore un peu et supprimer cette partition fédora pour réinstaller tout neuf et voir si ça marche mieux.
Sinon je vais peut-être repasser à la version 4 que je n'aurais jamais du mettre à jour (le mieux est l'ennemi du bien), ou tester une autre distribution.

Le pire sera de réinstaller Zope-plone-Python etc..
Le pire sera de réinstaller Zope-plone-Python etc..
re,
je comprends pas bien ce que tu veux dire, mais c'est sur que je n'utilise ni l'un, ni l'autre, ni l'autre encore. Mais pour l'installation, si tu fais :
$ yum install zope
$ yum install plone
$yum install python
à mon avis, tu as ces trois bidules d'installés, non ?
C'est sans doute la configuration qui demande plus de travail ? Surtout qu'il y a parfois des différences de configuration entre des versions différentes. Enfin, pour moi, c'est ça qui prend du temps, pour toi je ne sais pas vraiment, vu que je n'utilise pas ces trucs là.
Bonsoir eddy33,

Voici le résultat des commandes que tu demandais, dmesg et fdisk -l + modprobe pppoatm + pppd call ueagle-atm + [root@localhost ~]# grep pppd /var/log/messages .

J'espère que le résultat donnera des infos sur le Pb.

Logonna
[root@localhost ~]# modprobe pppoatm
[root@localhost ~]# pppd call ueagle-atm
Plugin pppoatm.so loaded.
PPPoATM plugin_init
PPPoATM setdevname_pppoatm - SUCCESS:8.35
[root@localhost ~]#


Puis: [root@localhost ~]# grep pppd /var/log/messages

Feb 27 23:41:20 localhost pppd[3140]: Plugin pppoatm.so loaded.
Feb 27 23:41:20 localhost pppd[3140]: PPPoATM plugin_init
Feb 27 23:41:20 localhost pppd[3140]: PPPoATM setdevname_pppoatm - SUCCESS:8.35
Feb 27 23:41:20 localhost pppd[3141]: pppd 2.4.4 started by root, uid 0
Feb 27 23:41:20 localhost pppd[3141]: Using interface ppp0
Feb 27 23:41:20 localhost pppd[3141]: Connect: ppp0 <--> 8.35
Feb 27 23:41:20 localhost pppd[3141]: Couldn't increase MTU to 1500. Using 1492
Feb 27 23:41:20 localhost pppd[3141]: Couldn't increase MRU to 1500. Using 1492
Feb 27 23:41:50 localhost pppd[3141]: LCP: timeout sending Config-Requests
Feb 27 23:41:50 localhost pppd[3141]: Connection terminated.
Feb 27 23:41:50 localhost pppd[3141]: Modem hangup
Feb 27 23:42:20 localhost pppd[3141]: Using interface ppp0
Feb 27 23:42:20 localhost pppd[3141]: Connect: ppp0 <--> 8.35
Feb 27 23:42:20 localhost pppd[3141]: Couldn't increase MTU to 1500. Using 1492
Feb 27 23:42:20 localhost pppd[3141]: Couldn't increase MRU to 1500. Using 1492

---------------------------------------------------------------------------------------

[root@localhost ~]# fdisk -l

Disk /dev/sda: 203.9 GB, 203928109056 bytes
255 heads, 63 sectors/track, 24792 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

Device Boot Start End Blocks Id System
/dev/sda1 * 1 9493 76252491 7 HPFS/NTFS
/dev/sda2 9494 24791 122881185 f W95 Ext'd (LBA)
/dev/sda5 9494 24791 122881153+ 7 HPFS/NTFS

Disk /dev/sdb: 203.9 GB, 203928109056 bytes
255 heads, 63 sectors/track, 24792 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

Device Boot Start End Blocks Id System
/dev/sdb1 * 151 24792 197936865 83 Linux
/dev/sdb2 1 150 1204843+ 82 Linux swap / Solaris

Partition table entries are not in disk order

-------------------------------------------------------------------------------------------
Commande dmesg


Linux version 2.6.18-1.2798.fc6 (brewbuilder@hs20-bc2-4.build.redhat.com) (gcc version 4.1.1 20061011 (Red Hat 4.1.1-30)) #1 SMP Mon Oct 16 14:37:32 EDT 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f5240
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 262128
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 32752 pages, LIFO batch:7
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v000 Nvidia ) @ 0x000f9100
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3040
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff30c0
ACPI: SRAT (v001 AMD HAMMER 0x00000001 AMD 0x00000001) @ 0x3fff9680
ACPI: MCFG (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff9780
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff95c0
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:15 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
Detected 2211.357 MHz processor.
Built 1 zonelists. Total pages: 262128
Kernel command line: ro root=LABEL=/ rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c07ae000 soft=c078e000
PID hash table entries: 4096 (order: 12, 16384 bytes)
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1032772k/1048512k available (2138k kernel code, 14904k reserved, 868k data, 240k init, 131008k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4425.40 BogoMIPS (lpj=8850808)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 078bf3ff e3d3fbff 00000000 00000410 00000001 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20060707
CPU0: AMD Athlon(tm) 64 Processor 3500+ stepping 02
Total of 1 processors activated (4425.40 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
Brought up 1 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=424 bytes
sizeof(dentry)=148 bytes
sizeof(ext3inode)=600 bytes
sizeof(buffer_head)=52 bytes
sizeof(skbuff)=172 bytes
sizeof(task_struct)=1392 bytes
checking if image is initramfs... it is
Freeing initrd memory: 1476k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
PCI: No mmconfig possible on 0:18
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:09.0
Boot video device is 0000:05:00.0
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:01: ioport range 0x4000-0x407f could not be reserved
pnp: 00:01: ioport range 0x4080-0x40ff has been reserved
pnp: 00:01: ioport range 0x4400-0x447f has been reserved
pnp: 00:01: ioport range 0x4480-0x44ff could not be reserved
pnp: 00:01: ioport range 0x4800-0x487f has been reserved
pnp: 00:01: ioport range 0x4880-0x48ff has been reserved
PCI: Bridge: 0000:00:09.0
IO window: d000-dfff
MEM window: fe900000-fe9fffff
PREFETCH window: fea00000-feafffff
PCI: Bridge: 0000:00:0b.0
IO window: c000-cfff
MEM window: fe800000-fe8fffff
PREFETCH window: fe700000-fe7fffff
PCI: Bridge: 0000:00:0c.0
IO window: b000-bfff
MEM window: fe600000-fe6fffff
PREFETCH window: fe500000-fe5fffff
PCI: Bridge: 0000:00:0d.0
IO window: a000-afff
MEM window: fe400000-fe4fffff
PREFETCH window: fe300000-fe3fffff
PCI: Bridge: 0000:00:0e.0
IO window: 9000-9fff
MEM window: fe200000-fe2fffff
PREFETCH window: d0000000-dfffffff
PCI: Setting latency timer of device 0000:00:09.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 9, 2621440 bytes)
TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1172618895.580:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 8BDC589434DBC709
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Linking AER extended capability on 0000:00:0b.0
PCI: Linking AER extended capability on 0000:00:0c.0
PCI: Linking AER extended capability on 0000:00:0d.0
PCI: Linking AER extended capability on 0000:00:0e.0
PCI: Setting latency timer of device 0000:00:0b.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
Allocate Port Service[0000:00:0b.0:pcie03]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
Allocate Port Service[0000:00:0c.0:pcie03]
PCI: Setting latency timer of device 0000:00:0d.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
Allocate Port Service[0000:00:0d.0:pcie03]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
Allocate Port Service[0000:00:0e.0:pcie03]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (on)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x1
ACPI: Thermal Zone [THRM] (22 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 242
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
ide0: BM-DMA at 0xfb00-0xfb07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfb08-0xfb0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
hdb: HL-DT-STDVD-ROM GDR8163B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3500+ processors (version 2.00.00)
powernow-k8: BIOS error - no PSB or ACPI _PSS objects
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 240k freed
Write protecting the kernel read-only data: 386k
Time: tsc clocksource has been installed.
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 217, io mem 0xfebff000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.1 -> Link [APCL] -> GSI 22 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 225, io mem 0xfeb00000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
SCSI subsystem initialized
libata version 2.00 loaded.
sata_nv 0000:00:07.0: version 2.0
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 21 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:07.0 to 64
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xF600 irq 233
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xF608 irq 233
scsi0 : sata_nv
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7, max UDMA/133, 398297088 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : sata_nv
ohci_hcd 0000:00:02.0: wakeup
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATA-7, max UDMA/133, 398297088 sectors: LBA48 NCQ (depth 0/32)
ata2.00: ata2: dev 0 multi count 16
ata2.00: configured for UDMA/133
Vendor: ATA Model: Maxtor 6L200S0 Rev: BACE
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 >
sd 0:0:0:0: Attached scsi disk sda
Vendor: ATA Model: Maxtor 6V200E0 Rev: VA11
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 398297088 512-byte hdwr sectors (203928 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 398297088 512-byte hdwr sectors (203928 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2
sd 1:0:0:0: Attached scsi disk sdb
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 20 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:08.0 to 64
ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xF100 irq 50
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xF108 irq 50
scsi2 : sata_nv
usb 1-2: new full speed USB device using ohci_hcd and address 2
ata3: SATA link down (SStatus 0 SControl 300)
scsi3 : sata_nv
ata4: SATA link down (SStatus 0 SControl 300)
usb 1-2: configuration #1 chosen from 1 choice
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb 1-7: new full speed USB device using ohci_hcd and address 3
usb 1-7: configuration #1 chosen from 1 choice
usb 1-8: new low speed USB device using ohci_hcd and address 4
usb 1-8: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /class/input/input0
input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:02.0-8
input: Logitech USB Receiver as /class/input/input1
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:02.0-8
audit(1172618904.144:2): enforcing=1 old_enforcing=0 auid=4294967295
security: 3 users, 6 roles, 1560 types, 166 bools, 1 sens, 1024 cats
security: 58 classes, 48173 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev sdb1, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), not configured for labeling
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1172618904.432:3): policy loaded auid=4294967295
Linux video capture interface: v2.00
pwc: Unknown parameter `index'
hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdb: ATAPI 52X DVD-ROM drive, 256kB Cache, UDMA(33)
NET: Registered protocol family 8
NET: Registered protocol family 20
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.56.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:0a.0 to 64
forcedeth: using HIGHDMA
pwc: Unknown parameter `index'
[ueagle-atm] driver ueagle 1.3 loaded
usb 1-7: [ueagle-atm] ADSL device founded vid (0X1110) pid (0X900F) : Eagle I
input: PC Speaker as /class/input/input2
EDAC MC: Ver: 2.0.1 Oct 16 2006
usb 1-7: reset full speed USB device using ohci_hcd and address 3
eth0: forcedeth.c: subsystem: 01462:7125 bound to 0000:00:0a.0
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40
EDAC MC0: Giving out device to k8_edac Athlon64/Opteron: DEV 0000:00:18.2
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
usb 1-7: [ueagle-atm] using iso mode
usb 1-7: [ueagle-atm] (re)booting started
ATM dev 0: usbatm_submit_urb: urb 0xf7240b80 submission failed (-28)!
usbcore: registered new driver ueagle-atm
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCJ] -> GSI 22 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:04.0 to 64
intel8x0_measure_ac97_clock: measured 58690 usecs
intel8x0: clocking to 46952
usbcore: registered new driver snd-usb-audio
pwc: Unknown parameter `index'
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
lp0: console ready
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 58
[drm] Initialized radeon 1.25.0 20060524 on minor 0
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
EXT3 FS on sdb1, internal journal
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 1204832k swap on /dev/sdb2. Priority:-1 extents:1 across:1204832k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8191 buckets, 65528 max) - 228 bytes per conntrack
usb 1-7: [ueagle-atm] modem operational
usb 1-7: [ueagle-atm] ATU-R firmware version : 44e2ea17
eth0: no link during initialization.
ADDRCONF(NETDEV_UP): eth0: link is not ready
audit(1172615329.668:4): audit_pid=2078 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
SELinux: initialized (dev nfsd, type nfsd), uses genfs_contexts
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
[drm] Setting GART location based on new memory map
[drm] Loading R300 Microcode
Mais pour l'installation, si tu fais :
$ yum install zope
$ yum install plone
$yum install python
à mon avis, tu as ces trois bidules d'installés, non ?
Non....pas en tant que simple utilisateur, et c'est le cas avec tes commandes "$ yum install"
arf ben oui, désolé, je m'embrouille entre le dièse et le dollar, il est tard...
c'est bien sur :
# yum install trucsysteme
puisque le # indique une console root et qu'il faut être root pour installer quelque chose.
Merci pour la pertinence de ta remarque, enfin, ça va pas aider logonna à faire marcher son modem, mais vaut mieux rétablir la rectitude, 's'pas ?
hum...

DD : Tu as 2 DD sda avec win$ et sdb avec Linux...je suppose que ton DD USB externe est celui avec win$...tu pourras y acceder quand tu auras installe le module kmod-ntfs.

modem : ueagle. rien d'anormal...que renvoie :
# ifconfig -a

++

ps : revoie la config de :
/etc/ppp/peers/ueagle-atm
/etc/ppp/chap-secrets
notamment les noms et passwd...
Le 25 à 22:06:40 tu nous disais que dans deux heures tu crashais ta Fedora....

Nous sommes maintenant le 26 à 00:34:00 et je suis curieux de savoir comment ça s'est passé....

As-tu des photos du crash ? Est-ce que ça a fait des dégats ? Ne nous laisse pas dans l'ignorance....
logonna wrote:Pour le modem j'y ai pensé,

prende une livebox ou autre, c'est à dire payer 10 euros de plus par mois
Nan, tu peux demander a ton FAI de remplacer ton modem USB par un modem ethernet Pas de boite, pas de frais supplementaires ! (en tout cas pas chez Tele2, je l'ai fait pour ma mere 😉
uniquement pour avoir internet sous linux alors que sous XP je n'ai aucun problème (2 DD multi boot).
Les modems ethernet sont quand meme vachement plus stables, meme sous XP. En tout cas ma mere a beaucoup moins de problemes de deconnexions (elle est toujours sous XP, la migration est en cours 😛)
Et XP pour mes filles c'est "sacré" et je me vois mal les passer sous Linux avec tous mes emmerdes. Elle y font des jeux mais pas plus.
Les jeux sont vraiment necessairement sous Windows ? Et puis un dual boot c'est pas sorcier. J'ai Windows sur mon PC, il me sert uniquement a jouer, le reste se passe sous Fedora.
On à beau lire plein de belles choses, sur linux, il faut tout de même avoir une ame de developpeur car je ne connais pas grand monde qui irait aujoud'hui installer un logiciel autrement qu'en double cliquant sur un fichier
Ou en cochant le case correspondante au logiciel dans une liste de logiciels que l'on peut installer/mettre a jour/supprimer automatiquement, sans meme se casser le c** a aller les chercher un par un (et pour chaque mise a jour) sur le site de l'editeur. Question d'habitude c'est vrai, m'enfin un gestionnaire de paquet est quand meme hautement plus simple a utiliser (quand on a compris le principe je te l'accorde;).
Le forum c'est un outil formidable, hélas on y trouve pas de messages de gens satisfaits.
En v'la deux, trouves rapidement avec la fonction de recherche (la meme qui permet de trouver les posts de personnes qui ont eu le meme probleme que toi avec un modem aussi commun)
http://forums.fedora-fr.org/viewtopic.php?id=18750
http://forums.fedora-fr.org/viewtopic.php?id=17882
Crash dans 53 minutes
Logonna
Je me demande, comment on crashe un OS ? En crashant le PC avec ? J'aimerais voir ca 🙂
Le forum c'est un outil formidable, hélas on y trouve pas de messages de gens satisfaits.
D'après mon expérience personnelle, tant que tu n'entends pas les gens se plaindre c'est que tout va bien :-D
Sinon tu le sais très vite. Quand sa fonctionne pas on le dit mais sinon .....:roll:
Trinita wrote:
Le forum c'est un outil formidable, hélas on y trouve pas de messages de gens satisfaits.
JE SUIS TRES SATISFAIT !
nouvo09 wrote:
Trinita wrote:
Le forum c'est un outil formidable, hélas on y trouve pas de messages de gens satisfaits.
JE SUIS TRES SATISFAIT !
Mais tu ne le dis jamais... Ah ben si, tu viens de le faire :lol:
Tiens... bizarre mais j'ai vu des messages de remerciements et de gens contents 🙂 mince alors! mais? quoi! il y a une fonction recherche en haut à gauche! et bien zut alors :-D

Les programmes plantes : ben c'est pas toujours la faute à la distribution fedora!
Les pilotes proprio ne fonctionne pas? vas râler auprès des constructeurs!
Les programmes sont dure à installer? beaucoup moins qu'une recherche + pub + X résultats + pub + choix du programme + pub + téléchargement + pub + installation sur clubic/télécharger.com/etc...! c'est vrai que c'est le pied le monde minedos
Ça me plait pas/plus! et bien ta le choix! change de distribution! ou retourne sous minedos!
Mon modem USB ne fonctionne pas! j'ai déjà dit d'aller râler auprès du constructeur! si personne ne le fait! ils ne feront pas d'effort! Et ça fait des années que tout le monde s'accorde à dire que le modem usb c'est pas le pied! (comme le wifi d'ailleurs!) l'ethernet fonctionne très très bien! j'ai même mis une livebox sur un pc de 1996 avec win98 et il a aucun problèmes!

Voilà! ben bon courage à toi si tu vas voir ailleurs! après, avis perso, ça me gène pas de te revoir par ici!

PS : le hasben c'est normal quand tout les acteurs du monde informatique ne bosse qu'avec toi, et bien les autres peuvent aller ce brosser! MAIS BORDEL! UNE FOIS ENCORE CE N'EST AUCUNEMENT LA FAUTE AUX DISTRIBUTION GNU/LINUX! ben quoi? ras le bol d'avoir la même remarque à la con alors qu'il suffit de gueuler auprès des constructeurs/éditeurs etc...!
oui, il ne faut pas hésiter à râler auprès des constructeurs et éditeurs etc... si l'on veut qu'ils nous sortent des pilotes pour linux.
il faut faire remonter l'information chaque fois que nécessaire.
Je proteste...mon modem usb fonctionne parfaitement sur fedora6 apres avoir tres bien fonctionné sur fedora5...
Merci remi...
Et merci a tout ceux qui se decarcassent pour repondre a tout ces post...
Devrais-je tenter une autre distribution ?
Clairement ouais. Tu devrais. Mais, euh.. t'es parent avec Eric Raymond ?
C'est pas la documentation qui manque, ni l'aide sur les forum. Si tu peux pas lire un brin sans lancer un flame sur un forum...
Bonjour à tous,

Il est vrai que l'on bénéficie gratuitement d'outils très performants, merci à tous les développeurs de ces solutions.

Je dirais auusi pour me contredire que je suis très satisfait de mes partitions Linux une fois que j'ai tout paramêtré mais cela me prends toujours du temps par méconnaissance du système.

Pour l'évhande de mon modem avec un modem ethernet je vais me renseigner chez Orange.

Pour le Crash j'ai un peu de retard et j'espère encore pouvoir redresser le manche (sans jeu de mots)

Au sujet des constructeurs, je vais râler...

Merci à tous, je repasse sur ma Fedora pour faire les tests suggérés par eddy33.

Précision: mon disque dur externe USB est un troisieme disque de stockage uniquement.

A tout de suite
eddy33 wrote:hum...

DD : Tu as 2 DD sda avec win$ et sdb avec Linux...je suppose que ton DD USB externe est celui avec win$...tu pourras y acceder quand tu auras installe le module kmod-ntfs.
Accessoirement, ntfs-3g est maintenant bien maîtrisé et permet l'écriture sur les partitions Ntfs; il me semblerait utile de recommander ntfs-3g et non plus ntfs ... http://doc.fedora-fr.org/Ntfs-3g

Eddy33 va donc prendre un peu de temps pour poursuivre la rédaction du tutorial portant sur les services ...
Informations compléùentaires; suite aux commandes:
# ifconfig -a
/etc/ppp/peers/ueagle-atm
/etc/ppp/chap-secrets
# ifconfig -a

[root@localhost ~]# ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:13:D3:60:BA:0D
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interruption:217 Adresse de base:0x4000

lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1211 errors:0 dropped:0 overruns:0 frame:0
TX packets:1211 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:2663499 (2.5 MiB) TX bytes:2663499 (2.5 MiB)

sit0 Link encap:IPv6-dans-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

Puis pour voir la différence:
[root@localhost ~]# modprobe pppoatm
[root@localhost ~]# pppd call ueagle-atm
Plugin pppoatm.so loaded.
PPPoATM plugin_init
PPPoATM setdevname_pppoatm - SUCCESS:8.35
[root@localhost ~]#

[root@localhost ~]# ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:13:D3:60:BA:0D
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interruption:217 Adresse de base:0x4000

lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1211 errors:0 dropped:0 overruns:0 frame:0
TX packets:1211 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:2663499 (2.5 MiB) TX bytes:2663499 (2.5 MiB)

ppp0 Link encap:Protocole Point-Ã -Point
POINTOPOINT NOARP MULTICAST MTU:1492 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:3
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

sit0 Link encap:IPv6-dans-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)



pour /etc/ppp/peers/ueagle-atm

user "fti/-------@fti"
plugin pppoatm.so 8.35
noipdefault
usepeerdns
defaultroute
persist
noauth


pour /etc/ppp/chap-secrets

# Secrets for authentication using CHAP
# client server secret IP addresses
fti/-------@fti *------- *
Voila, est-ce qu'il y a quelque chose ?

ps login et mot de passe remplacer par -------
Merci d'avance
Logonna