RT2561/RT61 activation impossible

Ffuriousdante · 16 févr. 2007

Bonjour, hier j'ai installer ma RT2561/RT61 (avec se tuto http://doc.fedora-fr.org/Installation_du_wifi_-_Ralink et les driver rt2x00) et quand j'essaye de l'activer avec system-config-network j'ai se message qui s'affiche

[c]

Error for wireless request "Set Bit Rate" (8B20) :
    SET failed on device wlan0 ; Operation not supported.
Error for wireless request "Set Encode" (8B2A) :
    SET failed on device wlan0 ; Invalid argument.
SIOCSIFFLAGS: No such device
Erreur lors de l'activation de wlan0.

[/c]
PS: Quand j'ai fais sa:
screen hostapd /etc/hosatpd.conf
j'ai eu: bash: screen: command not found

[right]Merci d'avance furiousdante[/right]

Kkwizart · 16 févr. 2007

Tu es sur que tu as besoin du mode master ? (yum install screen pour installer screen !)
Ce n'est pas nécéssaire pour se connecter à un point d'accès!

Le rt2x00 tolère encore mal les outils tel system-config-network!
Modifies ton fichier /etc/sysconfig/network-scripts/ifcfg-wlan0 ainsi:

DEVICE=wlan0
ONBOOT=yes
TYPE=Wireless
USERCTL=yes

que donnes:
su -
lspci
dmesg |grep rt
ifconfig
ifconfig wlan0 up
iwconfig
iwlist scan

Ffuriousdante · 16 févr. 2007

En fait le pc est conecter sur internet par ethernet et j'aimerai mettre le pc en point d'acces pour ma psp et pour des pc qui sont equiper de wifi

lspci

00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge (rev 80)
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge
00:0d.0 Network controller: RaLink RT2561/RT61 rev B 802.11g
00:0f.0 IDE interface: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 78)
01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 4000 AGP 8x] (rev a4)

dmesg |grep rt

ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 20000000 (gap: 10000000:eec00000)
Enabling unmasked SIMD FPU exception support... done.
virtual kernel memory layout:
SELinux:  Starting in permissive mode
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Linux Plug and Play Support v0.97 (c) Adam Belay
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
pnp: 00:02: ioport range 0x4000-0x407f could not be reserved
pnp: 00:02: ioport range 0x5000-0x500f has been reserved
PCI: Bypassing VIA 8237 APIC De-Assert Message
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 64M @ 0xe4000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
powernow-k8: Processor cpuid 681 not supported
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
hub 1-0:1.0: 2 ports detected
hub 2-0:1.0: 2 ports detected
hub 3-0:1.0: 2 ports detected
hub 4-0:1.0: 2 ports detected
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 5-0:1.0: 8 ports detected
ATA: abnormal status 0x7F on port 0xE207
kjournald starting.  Commit interval 5 seconds
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
Loading module: rt61pci - CVS (N/A) by http://rt2x00.serialmonkey.com.
rt61pci->rt61pci_init_firmware_cont: Error - Failed to load Firmware.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode

ifconfig

eth0      Link encap:Ethernet  HWaddr 00:50:70:E7:4B:89
          inet adr:192.168.0.251  Bcast:192.168.0.255  Masque:255.255.255.0
          adr inet6: fe80::250:70ff:fee7:4b89/64 Scope:Lien
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:14924 errors:0 dropped:0 overruns:0 frame:0
          TX packets:13102 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 lg file transmission:1000
          RX bytes:14153220 (13.4 MiB)  TX bytes:1674382 (1.5 MiB)
          Interruption:18 Adresse de base:0xe000

lo        Link encap:Boucle locale
          inet adr:127.0.0.1  Masque:255.0.0.0
          adr inet6: ::1/128 Scope:Hôte
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:2130 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2130 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 lg file transmission:0
          RX bytes:5425634 (5.1 MiB)  TX bytes:5425634 (5.1 MiB)

ifconfig wlan0 up

SIOCSIFFLAGS: Aucun périphérique de ce type

iwconfig

lo        no wireless extensions.

eth0      no wireless extensions.

wmaster0  IEEE 802.11g  Frequency:2.412 GHz
          RTS thr:off   Fragment thr=2346 B

wlan0     IEEE 802.11g  ESSID:""
          Mode:Master  Frequency:2.412 GHz
          RTS thr:off   Fragment thr=2346 B
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

iwlist scan

lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

wmaster0  Interface doesn't support scanning : Operation not supported

wlan0     Interface doesn't support scanning : Network is down

Kkwizart · 16 févr. 2007

rt61pci->rt61pci_init_firmware_cont: Error - Failed to load Firmware.

Tu as oublié d'installer le firmware.... yum --enablerepo=kwizart install rt61-firmware

Ensuites fait:
su -
rmmod rt61pci
modprobe rt61pci
dmesg |grep tail
ifconfig wlan0 up
iwlist scan

Ffuriousdante · 16 févr. 2007

il s'active mais j'ai sa

Error for wireless request "Set Mode" (8B06) :
    SET failed on device wlan0:0 ; Device or resource busy.
Error for wireless request "Set Bit Rate" (8B20) :
    SET failed on device wlan0:0 ; Operation not supported.

et aucun pc quia le wifi ne le detecte

et

lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

wmaster0  Interface doesn't support scanning : Operation not supported

wlan0     No scan results

Kkwizart · 16 févr. 2007

Reprends les indications que je t'ai donné tu as loupé des étapes...
Oublies system-config-network avec ce module :
NE PAS UTILISER system-config-network !!!!

Eventuellement redemarres

Ffuriousdante · 16 févr. 2007

quand je fais iwconfig sa m'indique que je suis en mode master (mais aucun pc ne me le detecte)
puis quand je fais
su -
rmmod rt61pci
modprobe rt61pci
dmesg |grep tail
ifconfig wlan0 up
iwlist scan

il m'indique que je suis en manager

Kkwizart · 16 févr. 2007

il faut que tu me donne le résulat des commandes sinon cela ne sert à rien...
Si tu n'as pas le réseau directement, copie le réulsuat dans un fichier texte...

nicofo · 16 févr. 2007

ce que j'ai remarqué avec les rt2x00 : tu dois configurer ton wifi (=essid, key, ...) AVANT de monter ton interface.
==> pour résoudre ton problème :

ifconfig wlan0 down

<configure ici ton wifi À LA MAIN> :
iwconfig wlan0 mode master
iwconfig wlan0 essid <essid>
.. (voir la doc)

ifconfig wlan0 up

(au préalable, suprime le fichier /etc/sysconfig/network-scripts/ifcfg-wlan0 ou modifie-le comme au post #2)

Ffuriousdante · 17 févr. 2007

iwlist scan

lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

wmaster0  Interface doesn't support scanning : Operation not supported

wlan0     No scan results

iwconfig

lo        no wireless extensions.

eth0      no wireless extensions.

wmaster0  IEEE 802.11g  Frequency:2.412 GHz
          RTS thr:off   Fragment thr=2346 B

wlan0     IEEE 802.11g  ESSID:"furiousdante"
          Mode:Managed  Frequency:2.412 GHz  Access Point: Not-Associated
          RTS thr:off   Fragment thr=2346 B
          Encryption key:3078
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

Je teste ta techinque nicofo

Kkwizart · 17 févr. 2007

@furiousdante
Il manque la moitié des info! ( dmesg |grep rt )
Est ce que tu as installé le firmware ?

Ffuriousdante · 17 févr. 2007

iwlist scan

lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

wmaster0  Interface doesn't support scanning : Operation not supported

wlan0     No scan results

iwconfig

lo        no wireless extensions.

eth0      no wireless extensions.

wmaster0  IEEE 802.11g  Frequency:2.412 GHz
          RTS thr:off   Fragment thr=2346 B

wlan0     IEEE 802.11g  ESSID:"furiousdante"
          Mode:Managed  Frequency:2.412 GHz  Access Point: Not-Associated
          RTS thr:off   Fragment thr=2346 B
          Encryption key:3078
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

dmesg

wlan0: starting scan
wlan0: scan completed
(plien de fois)

grep rt

(j'ai rien)

et j'ai bien installer les driver

Kkwizart · 17 févr. 2007

je te demande si tu as bien installé le rt61-firmware !!!

dmesg |grep rt (tu as tres bien fait la commande un peu plus haut !)

Ffuriousdante · 17 févr. 2007

(oups j'ai fait separement le dmesg |grep rt)

wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan

et le rt61-firmware je l'ai installer

Kkwizart · 17 févr. 2007

il en manques... tu ne peux pas avoir que cela ou alors redemarres pour que tu ais le début du dmesg....(regardes ce que tu as mis plus haut est ce que tu as toujours l'erreur avec le firmware ?) Quel est le contenu du répertoire :
ls -al /lib/firmware ?

Pour la remarque de nicofo. Autant lorsque tu fais la configuration (iwconfig), tu dois avoir l'interface down (ifconfig wlan0 down ). Autant lorsque tu dois lister les reseaux disponible il me semble que l'interface doit être monté (ifconfig wlan0 up)...

Ffuriousdante · 17 févr. 2007

apres un redemarage

[root@localhost ~]# dmesg |grep rt
ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 20000000 (gap: 10000000:eec00000)
Enabling unmasked SIMD FPU exception support... done.
virtual kernel memory layout:
SELinux:  Starting in permissive mode
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Linux Plug and Play Support v0.97 (c) Adam Belay
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
pnp: 00:02: ioport range 0x4000-0x407f could not be reserved
pnp: 00:02: ioport range 0x5000-0x500f has been reserved
PCI: Bypassing VIA 8237 APIC De-Assert Message
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 64M @ 0xe4000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
powernow-k8: Processor cpuid 681 not supported
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
hub 1-0:1.0: 2 ports detected
hub 2-0:1.0: 2 ports detected
hub 3-0:1.0: 2 ports detected
hub 4-0:1.0: 2 ports detected
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 5-0:1.0: 8 ports detected
ATA: abnormal status 0x7F on port 0xE207
kjournald starting.  Commit interval 5 seconds
Loading module: rt61pci - CVS (N/A) by http://rt2x00.serialmonkey.com.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan
wlan0: starting scan

Kkwizart · 17 févr. 2007

ok...

Et donc tu as testé iwlist scan interface monté ou démonté ?

Ffuriousdante · 17 févr. 2007

[root@localhost ~]#  ifconfig wlan0 up
[root@localhost ~]# iwlist scan
lo        Interface doesn't support scanning.

wmaster0  Interface doesn't support scanning : Operation not supported

wlan0     No scan results
eth0      Interface doesn't support scanning.

[root@localhost ~]#  ifconfig wlan0 down
[root@localhost ~]# iwlist scan
lo        Interface doesn't support scanning.

wmaster0  Interface doesn't support scanning : Operation not supported

wlan0     Interface doesn't support scanning : Network is down

eth0      Interface doesn't support scanning

Kkwizart · 17 févr. 2007

hum... tu es sensé avoir des réseaux aux alentour ou tu vis à la campagne ?
Si tu veux l'utiliser en tant que point d'accès que donnes la suite de la configuration au lancement de hostapd ?
(enventuellement n'utilises pas screen !)

Ffuriousdante · 17 févr. 2007

je vis a la campagne et personne au alentour a le wifi (et très peux l'adsl)
et pour screen hostapd /etc/hosatpd.con

[root@localhost ~]# screen hostapd /etc/hosatpd.conf
[screen is terminating]
[root@localhost ~]#