maintenant mon dongle s'allume des le démarrage meme si j'ai à un moment donné:
activation interface Wlan0 [Echoué]
voila j'ai essayé de m'inspiré ce tuto :
http://easynux.org/forum/viewtopic.php?id=79
sur la fin , quand je fait: iwlist wlan0 scan j'obtient:
[root@local ~]# iwlist wlan0 scan
Warning: Driver for device wlan0 has been compiled with version 20
of Wireless Extension, while this program supports up to version 19.
Some things may be broken...
wlan0 Scan completed :
Cell 01 - Address: 00:16:CE:1B:78:17
ESSID:"WANADOO-3930"
Protocol:IEEE 802.11g
Mode:Managed
Frequency:2.412 GHz (Channel 1)
Quality:0/100 Signal level:-44 dBm Noise level:-256 dBm
Encryption key:on
Bit Rates:54 Mb/s; 48 Mb/s; 36 Mb/s; 24 Mb/s; 18 Mb/s
12 Mb/s; 11 Mb/s; 9 Mb/s; 6 Mb/s; 5.5 Mb/s
2 Mb/s; 1 Mb/s
Extra:bcn_int=100
Extra:atim=0
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : PSK
Cell 02 - Address: 00:14:A4:4B:4B:A6
ESSID:"WANADOO-344C"
Protocol:IEEE 802.11g
Mode:Managed
Frequency:2.412 GHz (Channel 1)
Quality:0/100 Signal level:-90 dBm Noise level:-256 dBm
Encryption key:on
Bit Rates:54 Mb/s; 48 Mb/s; 36 Mb/s; 24 Mb/s; 18 Mb/s
12 Mb/s; 11 Mb/s; 9 Mb/s; 6 Mb/s; 5.5 Mb/s
2 Mb/s; 1 Mb/s
Extra:bcn_int=100
Extra:atim=0
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : PSK
cell 02 étant celui de mon voisin ^^
j'éssai de définir mes parametres de connection dans la console avec
[root@local ~]# iwconfig wlan0 channel 1/canal
[root@local ~]# iwconfig wlan0 mode managed/mode
[root@local ~]# iwconfig wlan0 ESSID WANADOO-3930/SSID
[root@local ~]# iwconfig wlan0 key XXXXXXXXXXXXXXXXXXXXXXXXXXX /ma clé wep
[root@local ~]# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
sit0 no wireless extensions.
Warning: Driver for device wlan0 has been compiled with version 20
of Wireless Extension, while this program supports up to version 19.
Some things may be broken...
wlan0 IEEE 802.11FH ESSID:off/any Nickname:"local.localhost"
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Bit Rate=11 Mb/s Tx-Power:18 dBm Sensitivity=0/3
RTS thr=2312 B Fragment thr=2312 B
Encryption key:821F-6F77-39C0-B794-E169-B321-EE Security mode:restricted
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
donc voila dans le iwconfig on voit tres bien que Wlan0 n'est pas connecter à mon réseau sans-fil WANADOO-3930... je vais essayer ce que dr.pixel m'avais proposé de faire plus haut
merci à tous ++
