En fait, je ne suis pas obligé de laisser le boîtier ouvert l'été mais je le fais par précaution car il fait très lourd.
J'ai effectué les manipulations que je disais: nettoyage de certains ventilos, filtres... et j'ai remis de la pâte thermique au niveau du processeur et son dissipateur (d'ailleurs c'est un Noctua avec ventilo donc très bon) car j'ai bien l'impression qu'il y avait quasiment plus rien.
J'ai aussi mis un peu de pâte thermique sur le dissipateur de mon disque dur.
Voici un autre petit coup de sensors après avoir utilisé un jeu sous windows intensément puis reboot sous linux:
sensors
radeon-pci-0100
Adapter: PCI adapter
temp1: +87.0°C (crit = +120.0°C, hyst = +90.0°C)
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +62.9°C (high = +70.0°C)
(crit = +67.0°C, hyst = +62.0°C)
it8720-isa-0228
Adapter: ISA adapter
in0: +1.47 V (min = +0.00 V, max = +4.08 V)
in1: +1.94 V (min = +0.00 V, max = +4.08 V)
in2: +3.34 V (min = +0.00 V, max = +4.08 V)
+5V: +2.94 V (min = +0.00 V, max = +4.08 V)
in4: +3.02 V (min = +0.00 V, max = +4.08 V)
in5: +0.50 V (min = +0.00 V, max = +4.08 V)
in6: +3.34 V (min = +0.00 V, max = +4.08 V)
5VSB: +2.94 V (min = +0.00 V, max = +4.08 V)
Vbat: +3.25 V
fan1: 1486 RPM (min = 0 RPM)
fan2: 0 RPM (min = 0 RPM)
fan3: 1997 RPM (min = 0 RPM)
fan5: 0 RPM (min = 0 RPM)
temp1: +64.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
temp2: +63.0°C (low = +127.0°C, high = +127.0°C) sensor = thermal diode
temp3: +84.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
cpu0_vid: +1.250 V
intrusion0: ALARM
smartctl -a /dev/sda :
smartctl 6.2 2014-07-16 r3952 [x86_64-linux-3.14.27-100.fc19.x86_64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green
Device Model: WDC WD10EADS-00P8B0
Serial Number: WD-WMAVU0216876
LU WWN Device Id: 5 0014ee 0ac47e8ac
Firmware Version: 01.00A01
User Capacity: 1 000 204 886 016 bytes [1,00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Fri Jan 8 13:35:52 2016 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (27480) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 315) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 175 172 021 Pre-fail Always - 6233
4 Start_Stop_Count 0x0032 096 096 000 Old_age Always - 4757
5 Reallocated_Sector_Ct 0x0033 198 198 140 Pre-fail Always - 15
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 085 085 000 Old_age Always - 11377
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 3941
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 124
193 Load_Cycle_Count 0x0032 086 086 000 Old_age Always - 343555
194 Temperature_Celsius 0x0022 088 088 000 Old_age Always - 62
196 Reallocated_Event_Count 0x0032 199 199 000 Old_age Always - 1
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 14
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
smartctl -a /dev/sdb :
smartctl 6.2 2014-07-16 r3952 [x86_64-linux-3.14.27-100.fc19.x86_64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Intel 320 Series SSDs
Device Model: INTEL SSDSA2CW160G3
Serial Number: CVPR13500AFQ160DGN
LU WWN Device Id: 5 001517 95967221d
Firmware Version: 4PC10362
User Capacity: 160 041 885 696 bytes [160 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Fri Jan 8 13:38:26 2016 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 1) seconds.
Offline data collection
capabilities: (0x75) SMART execute Offline immediate.
No Auto Offline data collection support.
Abort Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 1) minutes.
Conveyance self-test routine
recommended polling time: ( 1) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 5
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0020 100 100 000 Old_age Offline - 0
4 Start_Stop_Count 0x0030 100 100 000 Old_age Offline - 0
5 Reallocated_Sector_Ct 0x0032 100 100 000 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 7686
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 2686
170 Reserve_Block_Count 0x0033 100 100 010 Pre-fail Always - 0
171 Program_Fail_Count 0x0032 100 100 000 Old_age Always - 0
172 Erase_Fail_Count 0x0032 100 100 000 Old_age Always - 0
183 SATA_Downshift_Count 0x0030 100 100 000 Old_age Offline - 4
184 End-to-End_Error 0x0032 100 100 090 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
192 Unsafe_Shutdown_Count 0x0032 100 100 000 Old_age Always - 97
199 CRC_Error_Count 0x0030 100 100 000 Old_age Offline - 3
225 Host_Writes_32MiB 0x0032 100 100 000 Old_age Always - 246632
226 Workld_Media_Wear_Indic 0x0032 100 100 000 Old_age Always - 1125
227 Workld_Host_Reads_Perc 0x0032 100 100 000 Old_age Always - 99
228 Workload_Minutes 0x0032 100 100 000 Old_age Always - 461192
232 Available_Reservd_Space 0x0033 100 100 010 Pre-fail Always - 0
233 Media_Wearout_Indicator 0x0032 099 099 000 Old_age Always - 0
241 Host_Writes_32MiB 0x0032 100 100 000 Old_age Always - 246632
242 Host_Reads_32MiB 0x0032 100 100 000 Old_age Always - 339722
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.