Bonjour

J'ai un soucis depuis quelques jours lorsque j'utilise libreoffice sous F21.
Après un temps variable, l'affichage se bloque, je n'ai plus accès à rien depuis le PC, le curseur de la souris bouge encore quelques minutes puis se fige également.
Je peux accéder en ssh à la session depuis un autre PC. Tout semble fonctionner, mais impossible de relancer la session, le seul moyen est d'éteindre en dur le PC.
J'ai essayé de relancer la session ou de tuer les processus (gdm, gnome-session, etc) pour relancer la session, mais rien ne fonctionne.
Depuis la session ssh, si je mets la commande reboot ou poweroff, la session ssh se ferme, rien ne se passe sur le PC, il reste dans le même état et je ne peux plus y accéder en ssh...
reboot en dur obligatoire.

la carte vidéo est une nvidia (NVIDIA Corporation GT218M [NVS 3100M] ) et j'utilise le pilote nouveau.
J'ai essayé d'installer le kmod-nvidia, mais j'ai eu "Oh quelque chose c'est mal passé".

j'ai aussi souvent des problèmes avec nautilus qui plante régulièrement, tout est peut être lié...

GoreGoreBey
malgré les mises à jour, aucune amélioration.

Le seul changement est que la commande 'poweroff' par shh fonctionne, il faut juste être patient.
Cela permet au moins un arrêt moins brutal.
Et rien avec la commande dmesg qui parlerait d'erreur, plantage ou autre? Si ça plante dans nautilus, donc sans libreoffice on peut le sortir du périmètre.
Faudrait peut être creuser un peu plus la piste du pilote nvidia, mais sans plus de précision sur ce que tu as fais ça va être dur. Pourquoi avoir installé le kmod-nvidia et pas le akmod-nvidia par ex?
au prochain plantage je regarderai plus en détails ce que donne dmesg.

au niveau des pilotes nvidia, j'avais installé le kmod-nvidia et le akmod-nvidia. Malgré plusieurs redémarrage, j'ai toujours eu le message "quelque chose s'est mal passé".
donc je les ai enlevé tous les deux.
Bonsoir...lances "top" en console et ensuite lances "libreoffice" et regardes ce que te diras "top" (ça ressemble à une "fuite" de mémoire...)
Regardes si tu n'as pas un processus qui te bouffe de la mémoire ou du CPU..
j'ai déjà pu regarder les occupations mémoire et les taux d'occupation processeur lors des connexions par ssh et je n'ai pas relevé de problème particulier.
j'attends le prochain freeze pour regarder de plus près.
En attendant, si le freeze provient d'un problème matériel, ce qui arrive, tu peux essayer d'éliminer certaines pistes:
- disques durs, normalement des erreurs sont visibles via dmesg, et smartctl -a /dev/ton_disque peut aussi donner de precieuses informations
- la mémoire, là via memtest86+ (en iso ou installé via yum), le test est long mais en général il remonte bien les erreurs.

Il y a d'autres possibilités matérielles (chauffe, ou alim par ex) mais difficile à tester. Je pencherais plus sur un pépin de disque dur où t'as un peu le même genre de comportement. Quand tu te connecteras en ssh lors du prochain plantage, regarde si tu peux ecrire un fichier (touch ~/test) par ex, l'état des partitions montées avec la commande mount, et surtout le dmesg.
Voici ce que donne dmesg au démarrage
$ dmesg 
[    0.000000] CPU0 microcode updated early to revision 0x7, date = 2013-08-20
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.18.5-201.fc21.x86_64 (mockbuild@bkernel01.phx2.fedoraproject.org) (gcc version 4.9.2 20141101 (Red Hat 4.9.2-1) (GCC) ) #1 SMP Mon Feb 2 21:00:58 UTC 2015
[    0.000000] Command line: BOOT_IMAGE=/vmlinuz-3.18.5-201.fc21.x86_64 root=/dev/mapper/luks-8261b2a2-77aa-4d42-975e-9c862961722e ro rd.md=0 rd.lvm=0 rd.dm=0 rd.luks.uuid=luks-8261b2a2-77aa-4d42-975e-9c862961722e rd.luks.uuid=luks-fc0e3c50-1a47-4756-82f7-97448f39a157 vconsole.keymap=us rhgb quiet LANG=fr_FR.utf8
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x0000000000095bff] usable
[    0.000000] BIOS-e820: [mem 0x0000000000095c00-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000cf65efff] usable
[    0.000000] BIOS-e820: [mem 0x00000000cf65f000-0x00000000cf67efff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000cf67f000-0x00000000cf76efff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cf76f000-0x00000000cfffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed1b000-0x00000000fed1ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ff800000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000012fffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.6 present.
[    0.000000] DMI: Dell Inc. Latitude E6510/0N5KHN, BIOS A05 08/10/2010
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0x130000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 080000000 mask FC0000000 write-back
[    0.000000]   2 base 0C0000000 mask FF0000000 write-back
[    0.000000]   3 base 100000000 mask FC0000000 write-back
[    0.000000]   4 base 130000000 mask FF0000000 uncachable
[    0.000000]   5 base 0FFC00000 mask FFFC00000 write-protect
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820: last_pfn = 0xcf65f max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000f21a0-0x000f21af] mapped at [ffff8800000f21a0]
[    0.000000] Base memory trampoline at [ffff88000008f000] 8f000 size 24576
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x02039000, 0x02039fff] PGTABLE
[    0.000000] BRK [0x0203a000, 0x0203afff] PGTABLE
[    0.000000] BRK [0x0203b000, 0x0203bfff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x12fe00000-0x12fffffff]
[    0.000000]  [mem 0x12fe00000-0x12fffffff] page 2M
[    0.000000] BRK [0x0203c000, 0x0203cfff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x12c000000-0x12fdfffff]
[    0.000000]  [mem 0x12c000000-0x12fdfffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x100000000-0x12bffffff]
[    0.000000]  [mem 0x100000000-0x12bffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0xcf65efff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0xcf5fffff] page 2M
[    0.000000]  [mem 0xcf600000-0xcf65efff] page 4k
[    0.000000] RAMDISK: [mem 0x35d93000-0x36ec1fff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000FE300 000024 (v02 DELL  )
[    0.000000] ACPI: XSDT 0x00000000CF67DE18 000064 (v01 DELL   E2       06222004 MSFT 00010013)
[    0.000000] ACPI: FACP 0x00000000CF75FC18 0000F4 (v04 DELL   E2       06222004 MSFT 00010013)
[    0.000000] ACPI BIOS Warning (bug): 32/64X FACS address mismatch in FADT: 0xCF76BF40/0x00000000CF76ED40, using 32-bit address (20140926/tbfadt-283)
[    0.000000] ACPI: DSDT 0x00000000CF73E018 00A6C0 (v01 DELL   E2       00001001 INTL 20080729)
[    0.000000] ACPI: FACS 0x00000000CF76BF40 000040
[    0.000000] ACPI: APIC 0x00000000CF67CF18 00008C (v02 DELL   E2       06222004 MSFT 00010013)
[    0.000000] ACPI: TCPA 0x00000000CF76DD18 000032 (v02                 00000000      00000000)
[    0.000000] ACPI: MCFG 0x00000000CF76DC98 00003C (v01 A M I  GMCH945. 06222004 MSFT 00000097)
[    0.000000] ACPI: HPET 0x00000000CF76DC18 000038 (v01 DELL   E2       00000001 ASL  00000061)
[    0.000000] ACPI: BOOT 0x00000000CF76DB98 000028 (v01 DELL   E2       06222004 AMI  00010013)
[    0.000000] ACPI: SLIC 0x00000000CF766818 000176 (v03 DELL   E2       06222004 MSFT 00010013)
[    0.000000] ACPI: SSDT 0x00000000CF74D018 0009F1 (v01 PmRef  CpuPm    00003000 INTL 20080729)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x000000012fffffff]
[    0.000000] NODE_DATA(0) allocated [mem 0x12ffe8000-0x12fffbfff]
[    0.000000]  [ffffea0000000000-ffffea0004bfffff] PMD -> [ffff88012b600000-ffff88012f5fffff] on node 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   [mem 0x100000000-0x12fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x00094fff]
[    0.000000]   node   0: [mem 0x00100000-0xcf65efff]
[    0.000000]   node   0: [mem 0x100000000-0x12fffffff]
[    0.000000] Initmem setup node 0 [mem 0x00001000-0x12fffffff]
[    0.000000] On node 0 totalpages: 1046003
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3988 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 13210 pages used for memmap
[    0.000000]   DMA32 zone: 845407 pages, LIFO batch:31
[    0.000000]   Normal zone: 3072 pages used for memmap
[    0.000000]   Normal zone: 196608 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x03] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x05] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled)
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[    0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs
[    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.000000] PM: Registered nosave memory: [mem 0x00095000-0x00095fff]
[    0.000000] PM: Registered nosave memory: [mem 0x00096000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xcf65f000-0xcf67efff]
[    0.000000] PM: Registered nosave memory: [mem 0xcf67f000-0xcf76efff]
[    0.000000] PM: Registered nosave memory: [mem 0xcf76f000-0xcfffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xd0000000-0xf7ffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfed1afff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed1b000-0xfed1ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xff7fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xff800000-0xffffffff]
[    0.000000] e820: [mem 0xd0000000-0xf7ffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:1024 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
[    0.000000] PERCPU: Embedded 30 pages/cpu @ffff88012fc00000 s84480 r8192 d30208 u262144
[    0.000000] pcpu-alloc: s84480 r8192 d30208 u262144 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1029636
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-3.18.5-201.fc21.x86_64 root=/dev/mapper/luks-8261b2a2-77aa-4d42-975e-9c862961722e ro rd.md=0 rd.lvm=0 rd.dm=0 rd.luks.uuid=luks-8261b2a2-77aa-4d42-975e-9c862961722e rd.luks.uuid=luks-fc0e3c50-1a47-4756-82f7-97448f39a157 vconsole.keymap=us rhgb quiet LANG=fr_FR.utf8
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Memory: 4016796K/4184012K available (7591K kernel code, 1235K rwdata, 3272K rodata, 1496K init, 1552K bss, 167216K reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=1024 to nr_cpu_ids=8.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[    0.000000] NR_IRQS:65792 nr_irqs:488 0
[    0.000000] 	Offload RCU callbacks from all CPUs
[    0.000000] 	Offload RCU callbacks from CPUs: 0-7.
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] allocated 16777216 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 1728.949 MHz processor
[    0.000047] Calibrating delay loop (skipped), value calculated using timer frequency.. 3457.89 BogoMIPS (lpj=1728949)
[    0.000050] pid_max: default: 32768 minimum: 301
[    0.000060] ACPI: Core revision 20140926
[    0.010927] ACPI: All ACPI Tables successfully acquired
[    0.012704] Security Framework initialized
[    0.012712] SELinux:  Initializing.
[    0.012720] SELinux:  Starting in permissive mode
[    0.013203] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.014306] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.014784] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.014793] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.015042] Initializing cgroup subsys memory
[    0.015050] Initializing cgroup subsys devices
[    0.015053] Initializing cgroup subsys freezer
[    0.015055] Initializing cgroup subsys net_cls
[    0.015057] Initializing cgroup subsys blkio
[    0.015060] Initializing cgroup subsys perf_event
[    0.015062] Initializing cgroup subsys net_prio
[    0.015065] Initializing cgroup subsys hugetlb
[    0.015092] CPU: Physical Processor ID: 0
[    0.015094] CPU: Processor Core ID: 0
[    0.015099] mce: CPU supports 9 MCE banks
[    0.015109] CPU0: Thermal monitoring handled by SMI
[    0.015119] Last level iTLB entries: 4KB 512, 2MB 7, 4MB 7
Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
[    0.015223] Freeing SMP alternatives memory: 28K (ffffffff81eac000 - ffffffff81eb3000)
[    0.016426] ftrace: allocating 27470 entries in 108 pages
[    0.034520] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
[    0.044520] smpboot: CPU0: Intel(R) Core(TM) i7 CPU       Q 740  @ 1.73GHz (fam: 06, model: 1e, stepping: 05)
[    0.145529] Performance Events: PEBS fmt1+, 16-deep LBR, Nehalem events, Intel PMU driver.
[    0.145550] perf_event_intel: CPU erratum AAJ80 worked around
[    0.145552] perf_event_intel: CPUID marked event: 'bus cycles' unavailable
[    0.145554] ... version:                3
[    0.145555] ... bit width:              48
[    0.145557] ... generic registers:      4
[    0.145558] ... value mask:             0000ffffffffffff
[    0.145559] ... max period:             000000007fffffff
[    0.145560] ... fixed-purpose events:   3
[    0.145562] ... event mask:             000000070000000f
[    0.147476] x86: Booting SMP configuration:
[    0.147479] .... node  #0, CPUs:      #1
[    0.158932] CPU1 microcode updated early to revision 0x7, date = 2013-08-20
[    0.158964] CPU1: Thermal monitoring handled by SMI
[    0.161112] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.161241]  #2
[    0.172696] CPU2 microcode updated early to revision 0x7, date = 2013-08-20
[    0.172728] CPU2: Thermal monitoring handled by SMI
[    0.174908]  #3
[    0.186363] CPU3 microcode updated early to revision 0x7, date = 2013-08-20
[    0.186395] CPU3: Thermal monitoring handled by SMI
[    0.199718]  #4
[    0.199718] CPU4: Thermal monitoring handled by SMI
[    0.213091]  #5
[    0.213091] CPU5: Thermal monitoring handled by SMI
[    0.226457]  #6
[    0.226458] CPU6: Thermal monitoring handled by SMI
[    0.239818]  #7
[    0.239819] CPU7: Thermal monitoring handled by SMI
[    0.241923] x86: Booted up 1 node, 8 CPUs
[    0.241927] smpboot: Total of 8 processors activated (27663.18 BogoMIPS)
[    0.248149] devtmpfs: initialized
[    0.251660] PM: Registering ACPI NVS region [mem 0xcf67f000-0xcf76efff] (983040 bytes)
[    0.253114] atomic64_test: passed for x86-64 platform with CX8 and with SSE
[    0.253117] pinctrl core: initialized pinctrl subsystem
[    0.253166] RTC time: 12:18:22, date: 02/09/15
[    0.253293] NET: Registered protocol family 16
[    0.256462] cpuidle: using governor menu
[    0.256591] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.256593] ACPI: bus type PCI registered
[    0.256595] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.256703] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[    0.256706] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[    0.256880] PCI: Using configuration type 1 for base access
[    0.256889] dmi type 0xB1 record - unknown flag
[    0.257273] mtrr: your CPUs had inconsistent variable MTRR settings
[    0.257274] mtrr: probably your BIOS does not setup all CPUs.
[    0.257275] mtrr: corrected configuration.
[    0.261935] ACPI: Added _OSI(Module Device)
[    0.261937] ACPI: Added _OSI(Processor Device)
[    0.261939] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.261941] ACPI: Added _OSI(Processor Aggregator Device)
[    0.274493] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    0.291868] ACPI: Dynamic OEM Table Load:
[    0.291876] ACPI: SSDT 0xFFFF880129093400 00032A (v01 PmRef  Cpu0Ist  00003000 INTL 20080729)
[    0.292446] ACPI: Dynamic OEM Table Load:
[    0.292453] ACPI: SSDT 0xFFFF8801290B2000 000891 (v01 PmRef  Cpu0Cst  00003001 INTL 20080729)
[    0.298767] ACPI: Dynamic OEM Table Load:
[    0.298774] ACPI: SSDT 0xFFFF880129093C00 000303 (v01 PmRef  ApIst    00003000 INTL 20080729)
[    0.301597] ACPI: Dynamic OEM Table Load:
[    0.301603] ACPI: SSDT 0xFFFF88012908EE00 000119 (v01 PmRef  ApCst    00003000 INTL 20080729)
[    0.323589] ACPI: Interpreter enabled
[    0.323597] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20140926/hwxface-580)
[    0.323603] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140926/hwxface-580)
[    0.323623] ACPI: (supports S0 S3 S4 S5)
[    0.323625] ACPI: Using IOAPIC for interrupt routing
[    0.323657] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.512360] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[    0.512368] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.512411] \_SB_.PCI0:_OSC invalid UUID
[    0.512413] _OSC request data:1 1f 0 
[    0.512418] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
[    0.513489] PCI host bridge to bus 0000:00
[    0.513494] pci_bus 0000:00: root bus resource [bus 00-3e]
[    0.513496] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.513499] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.513501] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.513504] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xfeafffff]
[    0.513515] pci 0000:00:00.0: [8086:d132] type 00 class 0x060000
[    0.513658] pci 0000:00:03.0: [8086:d138] type 01 class 0x060400
[    0.513723] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
[    0.513775] pci 0000:00:03.0: System wakeup disabled by ACPI
[    0.513831] pci 0000:00:08.0: [8086:d155] type 00 class 0x088000
[    0.513957] pci 0000:00:08.1: [8086:d156] type 00 class 0x088000
[    0.514084] pci 0000:00:08.2: [8086:d157] type 00 class 0x088000
[    0.514206] pci 0000:00:08.3: [8086:d158] type 00 class 0x088000
[    0.514326] pci 0000:00:10.0: [8086:d150] type 00 class 0x088000
[    0.514430] pci 0000:00:10.1: [8086:d151] type 00 class 0x088000
[    0.514574] pci 0000:00:19.0: [8086:10ea] type 00 class 0x020000
[    0.514611] pci 0000:00:19.0: reg 0x10: [mem 0xe9600000-0xe961ffff]
[    0.514625] pci 0000:00:19.0: reg 0x14: [mem 0xe9680000-0xe9680fff]
[    0.514639] pci 0000:00:19.0: reg 0x18: [io  0x8040-0x805f]
[    0.514717] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[    0.514773] pci 0000:00:19.0: System wakeup disabled by ACPI
[    0.514839] pci 0000:00:1a.0: [8086:3b3c] type 00 class 0x0c0320
[    0.514870] pci 0000:00:1a.0: reg 0x10: [mem 0xe9670000-0xe96703ff]
[    0.514978] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[    0.515036] pci 0000:00:1a.0: System wakeup disabled by ACPI
[    0.515097] pci 0000:00:1b.0: [8086:3b56] type 00 class 0x040300
[    0.515121] pci 0000:00:1b.0: reg 0x10: [mem 0xe9660000-0xe9663fff 64bit]
[    0.515211] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.515269] pci 0000:00:1b.0: System wakeup disabled by ACPI
[    0.515331] pci 0000:00:1c.0: [8086:3b42] type 01 class 0x060400
[    0.515423] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.515482] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.515546] pci 0000:00:1c.1: [8086:3b44] type 01 class 0x060400
[    0.515646] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.515704] pci 0000:00:1c.1: System wakeup disabled by ACPI
[    0.515761] pci 0000:00:1c.2: [8086:3b46] type 01 class 0x060400
[    0.515849] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    0.515907] pci 0000:00:1c.2: System wakeup disabled by ACPI
[    0.515964] pci 0000:00:1c.3: [8086:3b48] type 01 class 0x060400
[    0.516051] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[    0.516113] pci 0000:00:1c.3: System wakeup disabled by ACPI
[    0.516179] pci 0000:00:1d.0: [8086:3b34] type 00 class 0x0c0320
[    0.516210] pci 0000:00:1d.0: reg 0x10: [mem 0xe9650000-0xe96503ff]
[    0.516319] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.516378] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.516440] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401
[    0.516550] pci 0000:00:1e.0: System wakeup disabled by ACPI
[    0.516611] pci 0000:00:1f.0: [8086:3b07] type 00 class 0x060100
[    0.516835] pci 0000:00:1f.2: [8086:282a] type 00 class 0x010400
[    0.516865] pci 0000:00:1f.2: reg 0x10: [io  0x8090-0x8097]
[    0.516878] pci 0000:00:1f.2: reg 0x14: [io  0x8080-0x8083]
[    0.516891] pci 0000:00:1f.2: reg 0x18: [io  0x8070-0x8077]
[    0.516905] pci 0000:00:1f.2: reg 0x1c: [io  0x8060-0x8063]
[    0.516918] pci 0000:00:1f.2: reg 0x20: [io  0x8020-0x803f]
[    0.516931] pci 0000:00:1f.2: reg 0x24: [mem 0xe9640000-0xe96407ff]
[    0.516992] pci 0000:00:1f.2: PME# supported from D3hot
[    0.517098] pci 0000:00:1f.3: [8086:3b30] type 00 class 0x0c0500
[    0.517129] pci 0000:00:1f.3: reg 0x10: [mem 0xe9630000-0xe96300ff 64bit]
[    0.517156] pci 0000:00:1f.3: reg 0x20: [io  0x8000-0x801f]
[    0.517344] pci 0000:01:00.0: [10de:0a6c] type 00 class 0x030000
[    0.517356] pci 0000:01:00.0: reg 0x10: [mem 0xe2000000-0xe2ffffff]
[    0.517367] pci 0000:01:00.0: reg 0x14: [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.517377] pci 0000:01:00.0: reg 0x1c: [mem 0xe0000000-0xe1ffffff 64bit pref]
[    0.517385] pci 0000:01:00.0: reg 0x24: [io  0x7000-0x707f]
[    0.517392] pci 0000:01:00.0: reg 0x30: [mem 0xe3000000-0xe307ffff pref]
[    0.517499] pci 0000:01:00.1: [10de:0be3] type 00 class 0x040300
[    0.517511] pci 0000:01:00.1: reg 0x10: [mem 0xe3080000-0xe3083fff]
[    0.519634] pci 0000:00:03.0: PCI bridge to [bus 01]
[    0.519642] pci 0000:00:03.0:   bridge window [io  0x7000-0x7fff]
[    0.519649] pci 0000:00:03.0:   bridge window [mem 0xd0000000-0xe30fffff]
[    0.519763] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.519773] pci 0000:00:1c.0:   bridge window [io  0x6000-0x6fff]
[    0.519781] pci 0000:00:1c.0:   bridge window [mem 0xe8200000-0xe95fffff]
[    0.519947] pci 0000:03:00.0: [8086:422b] type 00 class 0x028000
[    0.520053] pci 0000:03:00.0: reg 0x10: [mem 0xe6e00000-0xe6e01fff 64bit]
[    0.520546] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[    0.520639] pci 0000:03:00.0: System wakeup disabled by ACPI
[    0.523664] pci 0000:00:1c.1: PCI bridge to [bus 03]
[    0.523677] pci 0000:00:1c.1:   bridge window [io  0x5000-0x5fff]
[    0.523694] pci 0000:00:1c.1:   bridge window [mem 0xe6e00000-0xe81fffff]
[    0.523865] pci 0000:04:00.0: [1180:e476] type 02 class 0x060700
[    0.523928] pci 0000:04:00.0: reg 0x10: [mem 0xe5940000-0xe5940fff]
[    0.524011] pci 0000:04:00.0: supports D1 D2
[    0.524014] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.524049] pci 0000:04:00.0: System wakeup disabled by ACPI
[    0.524168] pci 0000:04:00.1: [1180:e822] type 00 class 0x080501
[    0.524231] pci 0000:04:00.1: reg 0x10: [mem 0xe5930000-0xe59300ff]
[    0.524378] pci 0000:04:00.1: supports D1 D2
[    0.524381] pci 0000:04:00.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.524528] pci 0000:04:00.4: [1180:e832] type 00 class 0x0c0010
[    0.524587] pci 0000:04:00.4: reg 0x10: [mem 0xe5900000-0xe59007ff]
[    0.524741] pci 0000:04:00.4: supports D1 D2
[    0.524743] pci 0000:04:00.4: PME# supported from D0 D1 D2 D3hot D3cold
[    0.527721] pci 0000:00:1c.2: PCI bridge to [bus 04-05]
[    0.527731] pci 0000:00:1c.2:   bridge window [io  0x2000-0x3fff]
[    0.527740] pci 0000:00:1c.2:   bridge window [mem 0xe3100000-0xe59fffff]
[    0.527837] pci_bus 0000:05: busn_res: can not insert [bus 05-ff] under [bus 04-05] (conflicts with (null) [bus 04-05])
[    0.527847] pci_bus 0000:05: busn_res: [bus 05-ff] end is updated to 08
[    0.527850] pci_bus 0000:05: busn_res: can not insert [bus 05-08] under [bus 04-05] (conflicts with (null) [bus 04-05])
[    0.527858] pci_bus 0000:05: [bus 05-08] partially hidden behind bridge 0000:04 [bus 04-05]
[    0.527866] pci 0000:00:1c.2: bridge has subordinate 05 but max busn 08
[    0.527963] acpiphp: Slot [1] registered
[    0.527978] pci 0000:00:1c.3: PCI bridge to [bus 06-0b]
[    0.527987] pci 0000:00:1c.3:   bridge window [io  0x4000-0x4fff]
[    0.527996] pci 0000:00:1c.3:   bridge window [mem 0xe5a00000-0xe6dfffff]
[    0.528095] pci 0000:00:1e.0: PCI bridge to [bus 0c] (subtractive decode)
[    0.528110] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.528114] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.528117] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.528119] pci 0000:00:1e.0:   bridge window [mem 0xd0000000-0xfeafffff] (subtractive decode)
[    0.547524] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.547606] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.547686] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[    0.547765] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 11 12 14 15)
[    0.547843] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 *3 4 5 6 7 10 12 14 15)
[    0.547920] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[    0.547999] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.548077] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[    0.564316] ACPI: PCI Root Bridge [CPBG] (domain 0000 [bus 3f])
[    0.564322] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.564328] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[    0.564418] PCI host bridge to bus 0000:3f
[    0.564421] pci_bus 0000:3f: root bus resource [bus 3f]
[    0.564428] pci 0000:3f:00.0: [8086:2c52] type 00 class 0x060000
[    0.564492] pci 0000:3f:00.1: [8086:2c81] type 00 class 0x060000
[    0.564556] pci 0000:3f:02.0: [8086:2c90] type 00 class 0x060000
[    0.564614] pci 0000:3f:02.1: [8086:2c91] type 00 class 0x060000
[    0.564679] pci 0000:3f:03.0: [8086:2c98] type 00 class 0x060000
[    0.564735] pci 0000:3f:03.1: [8086:2c99] type 00 class 0x060000
[    0.564793] pci 0000:3f:03.4: [8086:2c9c] type 00 class 0x060000
[    0.564851] pci 0000:3f:04.0: [8086:2ca0] type 00 class 0x060000
[    0.564906] pci 0000:3f:04.1: [8086:2ca1] type 00 class 0x060000
[    0.564962] pci 0000:3f:04.2: [8086:2ca2] type 00 class 0x060000
[    0.565018] pci 0000:3f:04.3: [8086:2ca3] type 00 class 0x060000
[    0.565076] pci 0000:3f:05.0: [8086:2ca8] type 00 class 0x060000
[    0.565133] pci 0000:3f:05.1: [8086:2ca9] type 00 class 0x060000
[    0.565192] pci 0000:3f:05.2: [8086:2caa] type 00 class 0x060000
[    0.565250] pci 0000:3f:05.3: [8086:2cab] type 00 class 0x060000
[    0.581684] ACPI: Enabled 3 GPEs in block 00 to 3F
[    0.581752] ACPI : EC: GPE = 0x10, I/O: command/status = 0x934, data = 0x930
[    0.581888] vgaarb: setting as boot device: PCI:0000:01:00.0
[    0.581891] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.581895] vgaarb: loaded
[    0.581897] vgaarb: bridge control possible 0000:01:00.0
[    0.581989] SCSI subsystem initialized
[    0.582044] libata version 3.00 loaded.
[    0.582085] ACPI: bus type USB registered
[    0.582107] usbcore: registered new interface driver usbfs
[    0.582118] usbcore: registered new interface driver hub
[    0.582148] usbcore: registered new device driver usb
[    0.582281] PCI: Using ACPI for IRQ routing
[    0.583742] PCI: pci_cache_line_size set to 64 bytes
[    0.583851] e820: reserve RAM buffer [mem 0x00095c00-0x0009ffff]
[    0.583853] e820: reserve RAM buffer [mem 0xcf65f000-0xcfffffff]
[    0.583988] NetLabel: Initializing
[    0.583990] NetLabel:  domain hash size = 128
[    0.583991] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.584007] NetLabel:  unlabeled traffic allowed by default
[    0.584139] HPET: 8 timers in total, 5 timers will be used for per-cpu timer
[    0.584148] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 24, 25, 26, 27, 28, 0
[    0.584155] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[    0.586223] hpet: hpet2 irq 24 for MSI
[    0.586289] hpet: hpet3 irq 25 for MSI
[    0.586358] hpet: hpet4 irq 26 for MSI
[    0.586425] hpet: hpet5 irq 27 for MSI
[    0.586491] hpet: hpet6 irq 28 for MSI
[    0.586636] Switched to clocksource hpet
[    0.594739] pnp: PnP ACPI init
[    0.594932] system 00:00: [io  0x0680-0x069f] has been reserved
[    0.594936] system 00:00: [io  0x1000-0x1003] has been reserved
[    0.594938] system 00:00: [io  0x1004-0x1013] has been reserved
[    0.594941] system 00:00: [io  0xffff] has been reserved
[    0.594944] system 00:00: [io  0x0400-0x047f] could not be reserved
[    0.594946] system 00:00: [io  0x0500-0x057f] has been reserved
[    0.594949] system 00:00: [io  0x164e-0x164f] has been reserved
[    0.594953] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.595000] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.595040] pnp 00:02: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.612808] pnp 00:03: Plug and Play ACPI device, IDs PNP0401 (disabled)
[    0.612845] pnp 00:04: Plug and Play ACPI device, IDs DLL040b PNP0f13 (active)
[    0.613186] system 00:05: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.613190] system 00:05: [mem 0xfed1b000-0xfed1bfff] has been reserved
[    0.613193] system 00:05: [mem 0xf8000000-0xfbffffff] has been reserved
[    0.613195] system 00:05: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.613198] system 00:05: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.613201] system 00:05: [mem 0xff000000-0xffffffff] could not be reserved
[    0.613203] system 00:05: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.613206] system 00:05: [mem 0xe96c0000-0xe96c0fff] has been reserved
[    0.613209] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.643088] pnp: PnP ACPI: found 6 devices
[    0.651041] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000
[    0.651056] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000
[    0.651076] pci 0000:00:1c.2: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 04-05] add_size 200000
[    0.651089] pci 0000:00:1c.3: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 06-0b] add_size 200000
[    0.651107] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[    0.651109] pci 0000:00:1c.1: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[    0.651112] pci 0000:00:1c.2: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[    0.651115] pci 0000:00:1c.3: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[    0.651123] pci 0000:00:1c.0: BAR 15: assigned [mem 0xe9700000-0xe98fffff 64bit pref]
[    0.651129] pci 0000:00:1c.1: BAR 15: assigned [mem 0xe9900000-0xe9afffff 64bit pref]
[    0.651134] pci 0000:00:1c.2: BAR 15: assigned [mem 0xe9b00000-0xe9cfffff 64bit pref]
[    0.651139] pci 0000:00:1c.3: BAR 15: assigned [mem 0xe9d00000-0xe9efffff 64bit pref]
[    0.651143] pci 0000:00:03.0: PCI bridge to [bus 01]
[    0.651146] pci 0000:00:03.0:   bridge window [io  0x7000-0x7fff]
[    0.651151] pci 0000:00:03.0:   bridge window [mem 0xd0000000-0xe30fffff]
[    0.651157] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.651165] pci 0000:00:1c.0:   bridge window [io  0x6000-0x6fff]
[    0.651175] pci 0000:00:1c.0:   bridge window [mem 0xe8200000-0xe95fffff]
[    0.651184] pci 0000:00:1c.0:   bridge window [mem 0xe9700000-0xe98fffff 64bit pref]
[    0.651194] pci 0000:00:1c.1: PCI bridge to [bus 03]
[    0.651202] pci 0000:00:1c.1:   bridge window [io  0x5000-0x5fff]
[    0.651212] pci 0000:00:1c.1:   bridge window [mem 0xe6e00000-0xe81fffff]
[    0.651221] pci 0000:00:1c.1:   bridge window [mem 0xe9900000-0xe9afffff 64bit pref]
[    0.651233] pci 0000:04:00.0: res[15]=[mem 0x04000000-0x03ffffff pref] get_res_add_size add_size 4000000
[    0.651236] pci 0000:04:00.0: res[16]=[mem 0x04000000-0x03ffffff] get_res_add_size add_size 4000000
[    0.651239] pci 0000:04:00.0: res[13]=[io  0x0100-0x00ff] get_res_add_size add_size 100
[    0.651241] pci 0000:04:00.0: res[14]=[io  0x0100-0x00ff] get_res_add_size add_size 100
[    0.651245] pci 0000:04:00.0: BAR 15: no space for [mem size 0x04000000 pref]
[    0.651248] pci 0000:04:00.0: BAR 15: failed to assign [mem size 0x04000000 pref]
[    0.651251] pci 0000:04:00.0: BAR 16: no space for [mem size 0x04000000]
[    0.651254] pci 0000:04:00.0: BAR 16: failed to assign [mem size 0x04000000]
[    0.651257] pci 0000:04:00.0: BAR 13: assigned [io  0x2000-0x20ff]
[    0.651260] pci 0000:04:00.0: BAR 14: assigned [io  0x2400-0x24ff]
[    0.651264] pci 0000:04:00.0: BAR 16: no space for [mem size 0x04000000]
[    0.651266] pci 0000:04:00.0: BAR 16: failed to assign [mem size 0x04000000]
[    0.651269] pci 0000:04:00.0: BAR 15: no space for [mem size 0x04000000 pref]
[    0.651272] pci 0000:04:00.0: BAR 15: failed to assign [mem size 0x04000000 pref]
[    0.651274] pci 0000:04:00.0: CardBus bridge to [bus 05-08]
[    0.651277] pci 0000:04:00.0:   bridge window [io  0x2000-0x20ff]
[    0.651286] pci 0000:04:00.0:   bridge window [io  0x2400-0x24ff]
[    0.651295] pci 0000:00:1c.2: PCI bridge to [bus 04-05]
[    0.651303] pci 0000:00:1c.2:   bridge window [io  0x2000-0x3fff]
[    0.651313] pci 0000:00:1c.2:   bridge window [mem 0xe3100000-0xe59fffff]
[    0.651322] pci 0000:00:1c.2:   bridge window [mem 0xe9b00000-0xe9cfffff 64bit pref]
[    0.651332] pci 0000:00:1c.3: PCI bridge to [bus 06-0b]
[    0.651340] pci 0000:00:1c.3:   bridge window [io  0x4000-0x4fff]
[    0.651350] pci 0000:00:1c.3:   bridge window [mem 0xe5a00000-0xe6dfffff]
[    0.651359] pci 0000:00:1c.3:   bridge window [mem 0xe9d00000-0xe9efffff 64bit pref]
[    0.651369] pci 0000:00:1e.0: PCI bridge to [bus 0c]
[    0.651385] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.651388] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.651390] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.651392] pci_bus 0000:00: resource 7 [mem 0xd0000000-0xfeafffff]
[    0.651395] pci_bus 0000:01: resource 0 [io  0x7000-0x7fff]
[    0.651397] pci_bus 0000:01: resource 1 [mem 0xd0000000-0xe30fffff]
[    0.651400] pci_bus 0000:02: resource 0 [io  0x6000-0x6fff]
[    0.651402] pci_bus 0000:02: resource 1 [mem 0xe8200000-0xe95fffff]
[    0.651404] pci_bus 0000:02: resource 2 [mem 0xe9700000-0xe98fffff 64bit pref]
[    0.651407] pci_bus 0000:03: resource 0 [io  0x5000-0x5fff]
[    0.651409] pci_bus 0000:03: resource 1 [mem 0xe6e00000-0xe81fffff]
[    0.651411] pci_bus 0000:03: resource 2 [mem 0xe9900000-0xe9afffff 64bit pref]
[    0.651414] pci_bus 0000:04: resource 0 [io  0x2000-0x3fff]
[    0.651416] pci_bus 0000:04: resource 1 [mem 0xe3100000-0xe59fffff]
[    0.651418] pci_bus 0000:04: resource 2 [mem 0xe9b00000-0xe9cfffff 64bit pref]
[    0.651420] pci_bus 0000:05: resource 0 [io  0x2000-0x20ff]
[    0.651423] pci_bus 0000:05: resource 1 [io  0x2400-0x24ff]
[    0.651425] pci_bus 0000:06: resource 0 [io  0x4000-0x4fff]
[    0.651427] pci_bus 0000:06: resource 1 [mem 0xe5a00000-0xe6dfffff]
[    0.651430] pci_bus 0000:06: resource 2 [mem 0xe9d00000-0xe9efffff 64bit pref]
[    0.651432] pci_bus 0000:0c: resource 4 [io  0x0000-0x0cf7]
[    0.651434] pci_bus 0000:0c: resource 5 [io  0x0d00-0xffff]
[    0.651437] pci_bus 0000:0c: resource 6 [mem 0x000a0000-0x000bffff]
[    0.651439] pci_bus 0000:0c: resource 7 [mem 0xd0000000-0xfeafffff]
[    0.651478] NET: Registered protocol family 2
[    0.651720] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.651878] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.652078] TCP: Hash tables configured (established 32768 bind 32768)
[    0.652103] TCP: reno registered
[    0.652114] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.652157] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.652251] NET: Registered protocol family 1
[    0.652932] pci 0000:01:00.0: Video device with shadowed ROM
[    0.652990] PCI: CLS 64 bytes, default 64
[    0.653046] Unpacking initramfs...
[    1.012908] Freeing initrd memory: 17596K (ffff880035d93000 - ffff880036ec2000)
[    1.012919] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    1.012922] software IO TLB [mem 0xcb65f000-0xcf65f000] (64MB) mapped at [ffff8800cb65f000-ffff8800cf65efff]
[    1.013023] Simple Boot Flag at 0xf1 set to 0x1
[    1.013484] microcode: CPU0 sig=0x106e5, pf=0x10, revision=0x7
[    1.013495] microcode: CPU1 sig=0x106e5, pf=0x10, revision=0x7
[    1.013505] microcode: CPU2 sig=0x106e5, pf=0x10, revision=0x7
[    1.013511] microcode: CPU3 sig=0x106e5, pf=0x10, revision=0x7
[    1.013522] microcode: CPU4 sig=0x106e5, pf=0x10, revision=0x7
[    1.013532] microcode: CPU5 sig=0x106e5, pf=0x10, revision=0x7
[    1.013541] microcode: CPU6 sig=0x106e5, pf=0x10, revision=0x7
[    1.013550] microcode: CPU7 sig=0x106e5, pf=0x10, revision=0x7
[    1.013640] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    1.014983] futex hash table entries: 2048 (order: 5, 131072 bytes)
[    1.015014] Initialise system trusted keyring
[    1.015046] audit: initializing netlink subsys (disabled)
[    1.015062] audit: type=2000 audit(1423484302.892:1): initialized
[    1.015523] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.017442] zpool: loaded
[    1.017446] zbud: loaded
[    1.017719] VFS: Disk quotas dquot_6.5.2
[    1.017766] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.018235] msgmni has been set to 7879
[    1.018313] Key type big_key registered
[    1.018317] SELinux:  Registering netfilter hooks
[    1.019962] alg: No test for stdrng (krng)
[    1.019981] NET: Registered protocol family 38
[    1.019991] Key type asymmetric registered
[    1.019995] Asymmetric key parser 'x509' registered
[    1.020042] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.020128] io scheduler noop registered
[    1.020131] io scheduler deadline registered
[    1.020172] io scheduler cfq registered (default)
[    1.021217] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.021237] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.021295] intel_idle: MWAIT substates: 0x1120
[    1.021310] intel_idle: v0.4 model 0x1E
[    1.021312] intel_idle: lapic_timer_reliable_states 0x2
[    1.022472] ACPI: AC Adapter [AC] (off-line)
[    1.022908] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[    1.023400] ACPI: Lid Switch [LID]
[    1.023469] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[    1.023473] ACPI: Power Button [PBTN]
[    1.023532] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[    1.023540] ACPI: Sleep Button [SBTN]
[    1.023630] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    1.023635] ACPI: Power Button [PWRF]
[    1.024769] GHES: HEST is not enabled!
[    1.024935] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.029330] Non-volatile memory driver v1.3
[    1.029344] Linux agpgart interface v0.103
[    1.029990] ahci 0000:00:1f.2: version 3.0
[    1.032523] ahci 0000:00:1f.2: irq 29 for MSI/MSI-X
[    1.032685] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x33 impl RAID mode
[    1.032699] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems sxs apst 
[    1.043394] scsi host0: ahci
[    1.043982] scsi host1: ahci
[    1.044407] scsi host2: ahci
[    1.044896] scsi host3: ahci
[    1.045339] scsi host4: ahci
[    1.045820] scsi host5: ahci
[    1.046005] ata1: SATA max UDMA/133 abar m2048@0xe9640000 port 0xe9640100 irq 29
[    1.046019] ata2: SATA max UDMA/133 abar m2048@0xe9640000 port 0xe9640180 irq 29
[    1.046024] ata3: DUMMY
[    1.046029] ata4: DUMMY
[    1.046040] ata5: SATA max UDMA/133 abar m2048@0xe9640000 port 0xe9640300 irq 29
[    1.046052] ata6: SATA max UDMA/133 abar m2048@0xe9640000 port 0xe9640380 irq 29
[    1.046409] libphy: Fixed MDIO Bus: probed
[    1.046666] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.046684] ehci-pci: EHCI PCI platform driver
[    1.048103] ehci-pci 0000:00:1a.0: EHCI Host Controller
[    1.048236] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[    1.048281] ehci-pci 0000:00:1a.0: debug port 2
[    1.052814] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[    1.052865] ehci-pci 0000:00:1a.0: irq 16, io mem 0xe9670000
[    1.053980] ACPI: Battery Slot [BAT0] (battery present)
[    1.058697] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[    1.058784] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.058790] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.058795] usb usb1: Product: EHCI Host Controller
[    1.058800] usb usb1: Manufacturer: Linux 3.18.5-201.fc21.x86_64 ehci_hcd
[    1.058804] usb usb1: SerialNumber: 0000:00:1a.0
[    1.061688] hub 1-0:1.0: USB hub found
[    1.061704] hub 1-0:1.0: 3 ports detected
[    1.071718] ACPI: Battery Slot [BAT1] (battery absent)
[    1.079464] ehci-pci 0000:00:1d.0: EHCI Host Controller
[    1.079723] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    1.079772] ehci-pci 0000:00:1d.0: debug port 2
[    1.083721] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[    1.083758] ehci-pci 0000:00:1d.0: irq 17, io mem 0xe9650000
[    1.089708] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[    1.089796] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.089802] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.089806] usb usb2: Product: EHCI Host Controller
[    1.089811] usb usb2: Manufacturer: Linux 3.18.5-201.fc21.x86_64 ehci_hcd
[    1.089815] usb usb2: SerialNumber: 0000:00:1d.0
[    1.093238] hub 2-0:1.0: USB hub found
[    1.093254] hub 2-0:1.0: 3 ports detected
[    1.093593] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.093607] ohci-pci: OHCI PCI platform driver
[    1.093637] uhci_hcd: USB Universal Host Controller Interface driver
[    1.093738] usbcore: registered new interface driver usbserial
[    1.093754] usbcore: registered new interface driver usbserial_generic
[    1.093773] usbserial: USB Serial support registered for generic
[    1.093850] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    1.094818] i8042: Warning: Keylock active
[    1.096325] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.096336] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.096641] mousedev: PS/2 mouse device common for all mice
[    1.097989] rtc_cmos 00:01: RTC can wake from S4
[    1.098233] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[    1.098286] rtc_cmos 00:01: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
[    1.098370] device-mapper: uevent: version 1.0.3
[    1.098640] device-mapper: ioctl: 4.28.0-ioctl (2014-09-17) initialised: dm-devel@redhat.com
[    1.098974] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[    1.099526] hidraw: raw HID events driver (C) Jiri Kosina
[    1.099662] usbcore: registered new interface driver usbhid
[    1.099663] usbhid: USB HID core driver
[    1.099718] drop_monitor: Initializing network drop monitor service
[    1.099784] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.099922] TCP: cubic registered
[    1.099929] Initializing XFRM netlink socket
[    1.100055] NET: Registered protocol family 10
[    1.100572] mip6: Mobile IPv6
[    1.100576] NET: Registered protocol family 17
[    1.101464] Loading compiled-in X.509 certificates
[    1.102477] Loaded X.509 cert 'Fedora kernel signing key: 3f8ea986288c1999f32a50d2a37c05e54de8ec1e'
[    1.102492] registered taskstats version 1
[    1.103294]   Magic number: 3:194:329
[    1.103324] tty tty50: hash matches
[    1.103555] rtc_cmos 00:01: setting system clock to 2015-02-09 12:18:23 UTC (1423484303)
[    1.103626] PM: Hibernation image not present or could not be loaded.
[    1.355631] ata6: SATA link down (SStatus 0 SControl 300)
[    1.355672] ata5: SATA link down (SStatus 0 SControl 300)
[    1.355715] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.355753] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.357355] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[    1.361146] ata2.00: ATAPI: PLDS DVD+/-RW DU-8A3S, KD02, max UDMA/100
[    1.365285] ata2.00: configured for UDMA/100
[    1.376577] usb 1-1: new high-speed USB device number 2 using ehci-pci
[    1.395576] usb 2-1: new high-speed USB device number 2 using ehci-pci
[    1.400641] ata1.00: ATA-8: ST9500420AS, D005SDM1, max UDMA/133
[    1.400649] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[    1.403254] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[    1.403696] ata1.00: configured for UDMA/133
[    1.404214] scsi 0:0:0:0: Direct-Access     ATA      ST9500420AS      SDM1 PQ: 0 ANSI: 5
[    1.405059] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[    1.405136] sd 0:0:0:0: [sda] Write Protect is off
[    1.405143] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.405174] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.405210] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.409570] scsi 1:0:0:0: CD-ROM            PLDS     DVD+-RW DU-8A3S  KD02 PQ: 0 ANSI: 5
[    1.446463] sr 1:0:0:0: [sr0] scsi3-mmc drive: 24x/8x writer dvd-ram cd/rw xa/form2 cdda pop-up
[    1.446469] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.446910] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.447259] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.453501]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
[    1.455882] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.458537] Freeing unused kernel memory: 1496K (ffffffff81d36000 - ffffffff81eac000)
[    1.458542] Write protecting the kernel read-only data: 12288k
[    1.462804] Freeing unused kernel memory: 588K (ffff88000176d000 - ffff880001800000)
[    1.467799] Freeing unused kernel memory: 824K (ffff880001b32000 - ffff880001c00000)
[    1.471740] random: systemd urandom read with 45 bits of entropy available
[    1.491168] usb 1-1: New USB device found, idVendor=8087, idProduct=0020
[    1.491176] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.491798] hub 1-1:1.0: USB hub found
[    1.492005] hub 1-1:1.0: 6 ports detected
[    1.510342] usb 2-1: New USB device found, idVendor=8087, idProduct=0020
[    1.510350] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.510984] hub 2-1:1.0: USB hub found
[    1.511288] hub 2-1:1.0: 8 ports detected
[    1.766548] usb 1-1.4: new high-speed USB device number 3 using ehci-pci
[    1.788458] usb 2-1.7: new full-speed USB device number 3 using ehci-pci
[    1.849327] usb 1-1.4: New USB device found, idVendor=05ca, idProduct=1814
[    1.849336] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.849341] usb 1-1.4: Product: Laptop_Integrated_Webcam_3M
[    1.849346] usb 1-1.4: Manufacturer: CN06YWTK724870A3019Y
[    1.878943] usb 2-1.7: New USB device found, idVendor=413c, idProduct=8187
[    1.878952] usb 2-1.7: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.878957] usb 2-1.7: Product: DW375 Bluetooth Module
[    1.878962] usb 2-1.7: Manufacturer: Dell Computer Corp
[    1.878966] usb 2-1.7: SerialNumber: 5CAC4CFD455A
[    1.916979] ACPI: Video Device [VID1] (multi-head: yes  rom: no  post: no)
[    1.929304] pps_core: LinuxPPS API ver. 1 registered
[    1.929308] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.936253] PTP clock support registered
[    1.942195] usb 2-1.8: new full-speed USB device number 4 using ehci-pci
[    1.949211] wmi: Mapper loaded
[    1.949396] yenta_cardbus 0000:04:00.0: CardBus bridge found [1028:040b]
[    1.949454] yenta_cardbus 0000:04:00.0: CardBus bridge to [bus 05-08]
[    1.949460] yenta_cardbus 0000:04:00.0:   bridge window [io  0x2000-0x20ff]
[    1.949469] yenta_cardbus 0000:04:00.0:   bridge window [io  0x2400-0x24ff]
[    1.949483] yenta_cardbus 0000:04:00.0:   bridge window [mem 0xe3100000-0xe44fffff pref]
[    1.949496] yenta_cardbus 0000:04:00.0:   bridge window [mem 0xe4800000-0xe4bfffff]
[    1.964131] [drm] Initialized drm 1.1.0 20060810
[    1.967230] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.967233] e1000e: Copyright(c) 1999 - 2014 Intel Corporation.
[    2.017753] tsc: Refined TSC clocksource calibration: 1729.000 MHz
[    2.021445] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[    2.021477] e1000e 0000:00:19.0: irq 30 for MSI/MSI-X
[    2.042273] usb 2-1.8: New USB device found, idVendor=0a5c, idProduct=5800
[    2.042282] usb 2-1.8: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.042287] usb 2-1.8: Product: 5880
[    2.042291] usb 2-1.8: Manufacturer: Broadcom Corp
[    2.042296] usb 2-1.8: SerialNumber: 0123456789ABCD
[    2.042488] usb 2-1.8: config 0 descriptor??
[    2.072064] yenta_cardbus 0000:04:00.0: ISA IRQ mask 0x0000, PCI irq 18
[    2.072076] yenta_cardbus 0000:04:00.0: Socket status: 30000006
[    2.072082] pci_bus 0000:05: Upper limit for fixing this bridge's parent bridge: #05
[    2.072092] yenta_cardbus 0000:04:00.0: pcmcia: parent PCI bridge window: [io  0x2000-0x3fff]
[    2.072097] yenta_cardbus 0000:04:00.0: pcmcia: parent PCI bridge window: [mem 0xe3100000-0xe59fffff]
[    2.072103] pcmcia_socket pcmcia_socket0: cs: memory probe 0xe3100000-0xe59fffff:
[    2.072115]  excluding 0xe3100000-0xe4d2ffff 0xe5770000-0xe59fffff
[    2.072127] yenta_cardbus 0000:04:00.0: pcmcia: parent PCI bridge window: [mem 0xe9b00000-0xe9cfffff 64bit pref]
[    2.072133] pcmcia_socket pcmcia_socket0: cs: memory probe 0xe9b00000-0xe9cfffff:
[    2.072142]  excluding 0xe9b00000-0xe9cfffff
[    2.078070] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff:
[    2.078084]  excluding 0xc0000-0xfffff
[    2.078150] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff:
[    2.078161]  excluding 0xa0000000-0xa0ffffff
[    2.078222] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff:
[    2.078233]  excluding 0x60000000-0x60ffffff
[    2.126151] firewire_ohci 0000:04:00.4: added OHCI v1.0 device as card 0, 4 IR + 4 IT contexts, quirks 0x11
[    2.151502] random: nonblocking pool is initialized
[    2.232324] acpi device:1f: registered as cooling_device8
[    2.263389] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 5c:26:0a:16:ff:6c
[    2.263398] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[    2.263527] e1000e 0000:00:19.0 eth0: MAC: 9, PHY: 10, PBA No: 2041FF-0FF
[    2.274617] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:1d/LNXVIDEO:01/input/input8
[    2.279665] e1000e 0000:00:19.0 em1: renamed from eth0
[    2.458604] ACPI Warning: \_SB_.PCI0.PEG3.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20140926/nsarguments-95)
[    2.458711] ACPI: \_SB_.PCI0.PEG3.VID_: failed to evaluate _DSM
[    2.459911] nouveau  [  DEVICE][0000:01:00.0] BOOT0  : 0x0a8600b1
[    2.459919] nouveau  [  DEVICE][0000:01:00.0] Chipset: GT218 (NVA8)
[    2.459924] nouveau  [  DEVICE][0000:01:00.0] Family : NV50
[    2.460015] nouveau  [   VBIOS][0000:01:00.0] checking PRAMIN for image...
[    2.534803] nouveau  [   VBIOS][0000:01:00.0] ... appears to be valid
[    2.534809] nouveau  [   VBIOS][0000:01:00.0] using image from PRAMIN
[    2.535087] nouveau  [   VBIOS][0000:01:00.0] BIT signature found
[    2.535095] nouveau  [   VBIOS][0000:01:00.0] version 70.18.53.00.02
[    2.535743] nouveau 0000:01:00.0: irq 31 for MSI/MSI-X
[    2.535762] nouveau  [     PMC][0000:01:00.0] MSI interrupts enabled
[    2.535811] nouveau  [     PFB][0000:01:00.0] RAM type: DDR3
[    2.535844] nouveau  [     PFB][0000:01:00.0] RAM size: 512 MiB
[    2.535849] nouveau  [     PFB][0000:01:00.0]    ZCOMP: 960 tags
[    2.540072] nouveau  [    VOLT][0000:01:00.0] GPU voltage: 1000000uv
[    2.545526] input: DualPoint Stick as /devices/platform/i8042/serio1/input/input7
[    2.561215] input: AlpsPS/2 ALPS DualPoint TouchPad as /devices/platform/i8042/serio1/input/input6
[    2.569188] nouveau  [  PTHERM][0000:01:00.0] FAN control: none / external
[    2.569212] nouveau  [  PTHERM][0000:01:00.0] fan management: automatic
[    2.569219] nouveau  [  PTHERM][0000:01:00.0] internal sensor: yes
[    2.589304] nouveau  [     CLK][0000:01:00.0] 03: core 135 MHz shader 270 MHz memory 135 MHz
[    2.589325] nouveau  [     CLK][0000:01:00.0] 07: core 405 MHz shader 810 MHz memory 405 MHz
[    2.589334] nouveau  [     CLK][0000:01:00.0] 0f: core 606 MHz shader 1468 MHz memory 790 MHz
[    2.589373] nouveau  [     CLK][0000:01:00.0] --: core 405 MHz shader 810 MHz memory 405 MHz
[    2.590863] [TTM] Zone  kernel: Available graphics memory: 2018664 kiB
[    2.590868] [TTM] Initializing pool allocator
[    2.590879] [TTM] Initializing DMA pool allocator
[    2.590905] nouveau  [     DRM] VRAM: 512 MiB
[    2.590909] nouveau  [     DRM] GART: 1048576 MiB
[    2.590916] nouveau  [     DRM] TMDS table version 2.0
[    2.590920] nouveau  [     DRM] DCB version 4.0
[    2.590924] nouveau  [     DRM] DCB outp 00: 048003b6 0f220014
[    2.590929] nouveau  [     DRM] DCB outp 01: 02033300 00000000
[    2.590933] nouveau  [     DRM] DCB outp 02: 028113a6 0f220010
[    2.590937] nouveau  [     DRM] DCB outp 03: 02011362 00020010
[    2.590941] nouveau  [     DRM] DCB outp 04: 088223c6 0f220010
[    2.590945] nouveau  [     DRM] DCB outp 05: 08022382 00020010
[    2.590949] nouveau  [     DRM] DCB conn 00: 00002047
[    2.590954] nouveau  [     DRM] DCB conn 01: 00101146
[    2.590957] nouveau  [     DRM] DCB conn 02: 00410246
[    2.590961] nouveau  [     DRM] DCB conn 03: 00000300
[    2.627209] firewire_core 0000:04:00.4: created device fw0: GUID 006afa81444fc000, S400
[    2.660521] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    2.660526] [drm] Driver supports precise vblank timestamp query.
[    2.715841] nouveau  [     DRM] MM: using COPY for buffer copies
[    3.029460] nouveau  [     DRM] allocated 1920x1080 fb: 0x70000, bo ffff8800c8bb7c00
[    3.029734] Switched to clocksource tsc
[    3.029753] fbcon: nouveaufb (fb0) is primary device
[    3.161352] Console: switching to colour frame buffer device 240x67
[    3.164545] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device
[    3.164547] nouveau 0000:01:00.0: registered panic notifier
[    3.167702] [drm] Initialized nouveau 1.2.1 20120801 for 0000:01:00.0 on minor 0
[   19.714501] PM: Starting manual resume from disk
[   19.714517] PM: Hibernation image partition 253:0 present
[   19.714522] PM: Looking for hibernation image.
[   19.756571] PM: Image not found (code -22)
[   19.756577] PM: Hibernation image not present or could not be loaded.
[   19.826047] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[   20.363405] systemd-journald[167]: Received SIGTERM from PID 1 (systemd).
[   21.807580] audit: type=1404 audit(1423484324.211:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
[   21.998579] SELinux: 2048 avtab hash slots, 104702 rules.
[   22.014592] SELinux: 2048 avtab hash slots, 104702 rules.
[   22.040722] SELinux:  8 users, 103 roles, 4987 types, 294 bools, 1 sens, 1024 cats
[   22.040725] SELinux:  83 classes, 104702 rules
[   22.044838] SELinux:  Permission audit_read in class capability2 not defined in policy.
[   22.044843] SELinux: the above unknown classes and permissions will be allowed
[   22.044847] SELinux:  Completing initialization.
[   22.044848] SELinux:  Setting up existing superblocks.
[   22.044853] SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
[   22.044861] SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
[   22.044866] SELinux: initialized (dev proc, type proc), uses genfs_contexts
[   22.044919] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   22.044935] SELinux: initialized (dev devtmpfs, type devtmpfs), uses transition SIDs
[   22.045432] SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
[   22.046167] SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
[   22.046170] SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
[   22.046174] SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
[   22.046176] SELinux: initialized (dev aio, type aio), not configured for labeling
[   22.046178] SELinux: initialized (dev devpts, type devpts), uses transition SIDs
[   22.046193] SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs
[   22.046197] SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
[   22.046203] SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
[   22.046212] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
[   22.046527] SELinux: initialized (dev securityfs, type securityfs), uses genfs_contexts
[   22.046529] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   22.046534] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   22.046613] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   22.046638] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[   22.046642] SELinux: initialized (dev pstore, type pstore), uses genfs_contexts
[   22.046644] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[   22.046646] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[   22.046648] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[   22.046654] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[   22.046657] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[   22.046658] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[   22.046660] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[   22.046666] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[   22.046668] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[   22.046670] SELinux: initialized (dev configfs, type configfs), uses genfs_contexts
[   22.046672] SELinux: initialized (dev drm, type drm), not configured for labeling
[   22.046679] SELinux: initialized (dev dm-1, type ext4), uses xattr
[   22.053079] audit: type=1403 audit(1423484324.457:3): policy loaded auid=4294967295 ses=4294967295
[   22.062856] systemd[1]: Successfully loaded SELinux policy in 338.764ms.
[   22.291123] systemd[1]: Relabelled /dev and /run in 52.712ms.
[   22.729794] systemd-sysv-generator[687]: Could not find init script for ebtables.service
[   22.729817] systemd-sysv-generator[687]: Could not find init script for dkms_autoinstaller.service
[   22.730577] systemd-sysv-generator[687]: Could not find init script for ebtables.service
[   22.730603] systemd-sysv-generator[687]: Could not find init script for dkms_autoinstaller.service
[   22.731220] systemd-sysv-generator[687]: Could not find init script for ebtables.service
[   22.731243] systemd-sysv-generator[687]: Could not find init script for dkms_autoinstaller.service
[   22.731846] systemd-sysv-generator[687]: Could not find init script for ebtables.service
[   22.731869] systemd-sysv-generator[687]: Could not find init script for dkms_autoinstaller.service
[   22.785588] systemd-sysv-generator[687]: Could not find init script for ebtables.service
[   22.785614] systemd-sysv-generator[687]: Could not find init script for dkms_autoinstaller.service
[   22.788097] systemd-sysv-generator[687]: Could not find init script for ebtables.service
[   22.788118] systemd-sysv-generator[687]: Could not find init script for dkms_autoinstaller.service
[   22.788756] systemd-sysv-generator[687]: Could not find init script for ebtables.service
[   22.788776] systemd-sysv-generator[687]: Could not find init script for dkms_autoinstaller.service
[   25.254895] SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
[   26.089395] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   26.089432] SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs
[   26.840036] SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
[   26.986251] EXT4-fs (dm-1): re-mounted. Opts: (null)
[   27.036783] systemd-journald[711]: Received request to flush runtime journal from PID 1
[   27.039035] RPC: Registered named UNIX socket transport module.
[   27.039038] RPC: Registered udp transport module.
[   27.039039] RPC: Registered tcp transport module.
[   27.039041] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   27.040283] SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
[   27.756969] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   27.758069] SELinux: initialized (dev nfsd, type nfsd), uses genfs_contexts
[   32.044714] parport_pc 00:03: [io  0x0378-0x037b]
[   32.044812] parport_pc 00:03: [io  0x0278-0x027b]
[   32.044901] parport_pc 00:03: [io  0x03bc-0x03bf]
[   32.044984] parport_pc 00:03: [io  0x0378-0x037b]
[   32.045094] parport_pc 00:03: [irq 7]
[   32.050299] EDAC MC: Ver: 3.0.0
[   32.052954] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   32.080336] EDAC i7core: Device not found: dev 00.0 PCI ID 8086:2c50
[   32.089594] ACPI Warning: SystemIO range 0x0000000000008000-0x000000000000801f conflicts with OpRegion 0x0000000000008000-0x000000000000800f (\_SB_.PCI0.SBUS.SMBI) (20140926/utaddress-258)
[   32.089601] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   32.158658] parport_pc 00:03: activated
[   32.158663] parport_pc 00:03: reported by Plug and Play ACPI
[   32.158888] parport_pc 00:03: disabled
[   32.367728] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[   32.395134] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042f conflicts with OpRegion 0x0000000000000400-0x000000000000047f (\PMIO) (20140926/utaddress-258)
[   32.395142] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   32.395147] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054f conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20140926/utaddress-258)
[   32.395151] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   32.395153] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053f conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20140926/utaddress-258)
[   32.395157] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   32.395158] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052f conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20140926/utaddress-258)
[   32.395162] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   32.395163] lpc_ich: Resource conflict(s) found affecting gpio_ich
[   32.430833] cfg80211: Calling CRDA to update world regulatory domain
[   33.179306] iTCO_vendor_support: vendor-support=0
[   33.190300] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[   33.203116] iTCO_wdt: Found a QM57 TCO device (Version=2, TCOBASE=0x0460)
[   33.203544] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   33.241531] input: Dell WMI hotkeys as /devices/virtual/input/input9
[   33.275865] sdhci: Secure Digital Host Controller Interface driver
[   33.275868] sdhci: Copyright(c) Pierre Ossman
[   33.288546] sdhci-pci 0000:04:00.1: SDHCI controller found [1180:e822] (rev 3)
[   33.288681] sdhci-pci 0000:04:00.1: No vmmc regulator found
[   33.288684] sdhci-pci 0000:04:00.1: No vqmmc regulator found
[   33.290955] mmc0: SDHCI controller on PCI [0000:04:00.1] using DMA
[   33.319727] Intel(R) Wireless WiFi driver for Linux, in-tree:d
[   33.319730] Copyright(c) 2003- 2014 Intel Corporation
[   33.319900] iwlwifi 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
[   33.320000] iwlwifi 0000:03:00.0: irq 32 for MSI/MSI-X
[   33.339871] iwlwifi 0000:03:00.0: Direct firmware load for iwlwifi-6000-6.ucode failed with error -2
[   33.339890] iwlwifi 0000:03:00.0: Direct firmware load for iwlwifi-6000-5.ucode failed with error -2
[   33.491579] iwlwifi 0000:03:00.0: loaded firmware version 9.221.4.1 build 25532 op_mode iwldvm
[   33.516008] ppdev: user-space parallel port driver
[   33.556866] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUG enabled
[   33.556873] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUGFS enabled
[   33.556874] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TRACING disabled
[   33.556877] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Ultimate-N 6300 AGN, REV=0x74
[   33.557023] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[   33.564109] iwlwifi 0000:03:00.0: RF_KILL bit toggled to disable radio.
[   33.591229] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
[   35.254111] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work properly. Using workaround
[   35.325928] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff:
[   35.325933]  excluding 0xc0000-0xfffff
[   35.325962] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff:
[   35.325966]  excluding 0xa0000000-0xa0ffffff
[   35.326017] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff:
[   35.326021]  excluding 0x60000000-0x60ffffff
[   35.943990] snd_hda_intel 0000:00:1b.0: irq 33 for MSI/MSI-X
[   35.944131] snd_hda_intel 0000:01:00.1: Disabling MSI
[   35.944138] snd_hda_intel 0000:01:00.1: Handle VGA-switcheroo audio client
[   35.965466] sound hdaudioC0D0: autoconfig: line_outs=1 (0xe/0x0/0x0/0x0/0x0) type:line
[   35.965471] sound hdaudioC0D0:    speaker_outs=1 (0xd/0x0/0x0/0x0/0x0)
[   35.965474] sound hdaudioC0D0:    hp_outs=1 (0xb/0x0/0x0/0x0/0x0)
[   35.965476] sound hdaudioC0D0:    mono: mono_out=0x0
[   35.965478] sound hdaudioC0D0:    inputs:
[   35.965480] sound hdaudioC0D0:      Dock Mic=0xf
[   35.965483] sound hdaudioC0D0:      Internal Mic=0x11
[   35.965485] sound hdaudioC0D0:      Mic=0xa
[   35.988109] input: HDA Intel MID Dock Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   35.988230] input: HDA Intel MID Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[   35.988338] input: HDA Intel MID Dock Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[   35.988486] input: HDA Intel MID Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[   36.249460] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/0000:01:00.1/sound/card1/input14
[   36.249669] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/0000:01:00.1/sound/card1/input15
[   36.249946] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/0000:01:00.1/sound/card1/input16
[   36.250129] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:03.0/0000:01:00.1/sound/card1/input17
[   36.401382] cfg80211: World regulatory domain updated:
[   36.401385] cfg80211:  DFS Master region: unset
[   36.401386] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   36.401388] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   36.401390] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   36.401391] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   36.401393] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   36.401395] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   36.401396] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   36.401397] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   36.401399] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   36.700959] Adding 4044796k swap on /dev/mapper/luks-fc0e3c50-1a47-4756-82f7-97448f39a157.  Priority:-1 extents:1 across:4044796k FS
[   36.823143] cfg80211: Calling CRDA for country: FR
[   36.839812] cfg80211: Regulatory domain changed to country: FR
[   36.839816] cfg80211:  DFS Master region: ETSI
[   36.839817] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   36.839820] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   36.839823] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   36.839826] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   36.839828] cfg80211:   (5490000 KHz - 5710000 KHz @ 160000 KHz), (N/A, 2700 mBm), (0 s)
[   36.839830] cfg80211:   (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[   38.349838] iwlwifi 0000:03:00.0 wlp3s0: renamed from wlan0
[   39.209036] Bluetooth: Core ver 2.19
[   39.209057] NET: Registered protocol family 31
[   39.209059] Bluetooth: HCI device and connection manager initialized
[   39.209067] Bluetooth: HCI socket layer initialized
[   39.209069] Bluetooth: L2CAP socket layer initialized
[   39.209076] Bluetooth: SCO socket layer initialized
[   39.267348] media: Linux media interface: v0.10
[   39.293380] Linux video capture interface: v2.00
[   39.310834] usbcore: registered new interface driver btusb
[   39.605379] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_3M (05ca:1814)
[   39.607254] input: Laptop_Integrated_Webcam_3M as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4:1.0/input/input18
[   39.607365] usbcore: registered new interface driver uvcvideo
[   39.607367] USB Video Class driver (1.1.1)
[   39.613598] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[   39.734912] SELinux: initialized (dev sda5, type ext4), uses xattr
[   44.825045] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null)
[   44.825058] SELinux: initialized (dev dm-2, type ext4), uses xattr
[   57.735212] audit: type=1305 audit(1423484360.154:4): audit_pid=985 old=0 auid=4294967295 ses=4294967295 subj=system_u:system_r:auditd_t:s0 res=1
[   58.024263] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   58.024267] Bluetooth: BNEP filters: protocol multicast
[   58.024276] Bluetooth: BNEP socket layer initialized
[   58.609776] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   58.711427] vboxdrv: module verification failed: signature and/or  required key missing - tainting kernel
[   58.716996] vboxdrv: Found 8 processor cores.
[   58.717419] vboxdrv: fAsync=0 offMin=0x1b6 offMax=0x13ff
[   58.717521] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[   58.717523] vboxdrv: Successfully loaded version 4.3.16 (interface 0x001a0007).
[   58.926927] vboxpci: IOMMU not found (not registered)
[   59.075197] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[   59.099165] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   59.151843] Ebtables v2.0 registered
[   59.173509] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[   59.988044] e1000e 0000:00:19.0: irq 30 for MSI/MSI-X
[   60.088645] e1000e 0000:00:19.0: irq 30 for MSI/MSI-X
[   62.888065] e1000e: em1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx
[   70.993480] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   73.600122] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[  144.500005] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[  145.691013] fuse init (API version 7.23)
[  145.717564] SELinux: initialized (dev fusectl, type fusectl), uses genfs_contexts
[  145.750669] SELinux: initialized (dev fuse, type fuse), uses genfs_contexts
[  148.440945] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[  149.200720] Bluetooth: RFCOMM TTY layer initialized
[  149.200733] Bluetooth: RFCOMM socket layer initialized
[  149.200818] Bluetooth: RFCOMM ver 1.11
[  149.283857] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs

les principaux messages apparaissant en rouge concerne l'ACPI

et le retour de smartctl -a /dev/sda
]# smartctl -a /dev/sda
smartctl 6.2 2014-07-16 r3952 [x86_64-linux-3.18.5-201.fc21.x86_64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Momentus 7200.4
Device Model:     ST9500420AS
Serial Number:    5VJ7K0CZ
LU WWN Device Id: 5 000c50 029cdf93d
Firmware Version: D005SDM1
User Capacity:    500 107 862 016 bytes [500 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    7200 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 2.6, 3.0 Gb/s
Local Time is:    Mon Feb  9 13:25:34 2015 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(    0) seconds.
Offline data collection
capabilities: 			 (0x73) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					No Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 109) minutes.
Conveyance self-test routine
recommended polling time: 	 (   3) minutes.
SCT capabilities: 	       (0x103f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   114   099   006    Pre-fail  Always       -       83756467
  3 Spin_Up_Time            0x0003   100   098   085    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   098   098   020    Old_age   Always       -       2414
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   076   060   030    Pre-fail  Always       -       13049647903
  9 Power_On_Hours          0x0032   091   091   000    Old_age   Always       -       8691
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   098   037   020    Old_age   Always       -       2099
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   099   000    Old_age   Always       -       1
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   074   054   045    Old_age   Always       -       26 (Min/Max 21/26)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       134
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       1
193 Load_Cycle_Count        0x0032   001   001   000    Old_age   Always       -       463518
194 Temperature_Celsius     0x0022   026   046   000    Old_age   Always       -       26 (0 12 0 0 0)
195 Hardware_ECC_Recovered  0x001a   042   038   000    Old_age   Always       -       83756467
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       1
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       178060754163721
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       2576232156
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       1033035930
254 Free_Fall_Sensor        0x0032   001   001   000    Old_age   Always       -       1

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%         1         -
# 2  Short offline       Completed without error       00%         0         -
# 3  Short offline       Completed without error       00%         0         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Le disque dur ayant p\us de 4 ans , je comprend qu'il faiblisse, mais les freezes ont uniquement lieu sous libreoffice.
j'utilise d'autres applications de façon beaucoup plus intensive (code maison ou éléments finis) sans soucis.

J'attends le prochain freeze pour comparer...
Je vais lancer memtest86+ en attendant.
j'étais partis du principe que ça plantait avec nautilus, si ça plante que sous libreoffice c'est autre chose. Peut être la piste de la carte video en effet, et donc du driver, vu que libreoffice si je ne me trompe pas depuis peu, peut uilister le GPU pour accelerer (ou afficher je sais pas) les traitements (via openCL me semble). A voir si ça peut se desactiver. peut être que regler cette histoire de pilote nvidia resoudrait ton freeze. En tout cas le dmesg au boot à l'air propre, et le smartcl est bon.
la confusion vient du fait que Nautilus plante aussi mais il ne bloque pas la machine comme libreoffice.
le memtest est en cours, c'est long ...
ah, mais c'est quand même grave que nautilus plante. Enfin c'est loin d'être normal.

pour memtest si t'as laissé tourner 1h ou 2 c'est bon. ça se termine jamais il va faire plusieurs passes si tu le laisse tourner.
j 'ai laissé 2 pass pour memtest, aucune erreur detectée.

Nautilus plante mais il refonctionne quelques secondes plus tard. Ce n'est pas normal mais peu génant.
bon, apparemment c'est la pilote nouveau qui pose problème :
[11314.940371] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[12834.784005] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[14914.116662] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[17722.180060] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[18512.055869] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[18948.858364] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[21612.606676] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[22111.309250] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[25709.214389] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[25947.240543] nouveau E[   PFIFO][0000:01:00.0] still angry after 101 spins, halt
[25947.334410] nouveau E[   PFIFO][0000:01:00.0] still angry after 101 spins, halt
[25947.468764] nouveau E[   PFIFO][0000:01:00.0] still angry after 101 spins, halt
[25958.290917] usb 1-1.2.1: USB disconnect, device number 10
[25958.290926] usb 1-1.2.1.1: USB disconnect, device number 11
[25958.356816] usb 1-1.2.1.2: USB disconnect, device number 12
[25958.415572] usb 1-1.2.1.3: USB disconnect, device number 13
le freeze a de nouveau eu lieu en utilisant libreoffice (justification d'un paragraphe sous writer).
aucune fuite de mémoire ni surcharge processeur, les température des processeurs sont également normales (<50C).

Je vais voir pour installer le pilote nvidia.
Apparemment, il doit y avoir un problème avec la carte graphique ou quelque chose s'y rattachant.

aucun des akmod-nvidia ne fonctionne.
Avec les akmod-nvidia et akmod-nvidia-340xx j'ai un plantage avec la fenêtre "quelque chose s'est mal passé"
avec la version 304xx, pas de lancement de l'interface graphique, l'affichage reste bloqué en mode texte.

Je vais voir pour faire une installation propre, vu que pour le moment c'est un upgrade.
Ya peut être des pistes dans les /var/log/Xorg.*
Tu as bien nouveau de blacklisté?
pour tester si le pilote nouveau était blacklisté ou non, j'ai reinstallé le akomd-nvidia-340xx et là je n'ai pas eu de soucis.
Le pilote nouveau est bien absent
$ lsmod |grep nouveau
ne revoie rien.
Je vais voir à l'usage avec le pilote nvidia.
Bonjour Orc libre,
Depuis quelques jours (suite à une mise à jour de LibreOffice Writer, je pense), j'ai également des freeze.
J'utilise la version suivante avec Fedora Core 20 :
Package : libreoffice-writer
Architecture : x86_64
Version : 1:4.2.8.2-2.fc20
Si cela peut t'aider,
Bonne journée,
lmaug
Je n'ai jamais eu de freeze ou autre avec quelque version de LibreOffice que ce soit, et j'en suis à la version 4.4.0
jusqu'à maintenant, tous les freezes sont survenus lors de l'utilisation de write (version 4.3.5.2.0+)
je n'ai ce soucis que depuis le passage sous F21.
Bonsoir à toutes et tous,
Je viens de ré-installer mon ordinateur (reformatage de mes partitions /, /boot et swap et conservation de ma partition /home) afin de passer de FC 20 à Fedora Core 21 pour essayer de solutionner mon problème de "freeze" sous Libreoffice Writer.

Le résultat de la commande "# yum info libreoffice-writer" est :
Modules complémentaires chargés : langpacks
Paquets installés
Nom : libreoffice-writer
Architecture : x86_64
Date : 1
Version : 4.3.5.2
Révision : 11.fc21
Taille : 16 M
Dépôt   : installed
Depuis le dépôt : updates
Résumé   : LibreOffice Word Processor Application
URL : http://www.libreoffice.org/
Licence   : (MPLv1.1 or LGPLv3+) and LGPLv3 and LGPLv2+ and BSD and (MPLv1.1 or GPLv2 or LGPLv2 or Netscape) and Public Domain and ASL 2.0 and Artistic and MPLv2.0 and CC0
Description  : The LibreOffice Word Processor application.

J'ai toujours des problèmes de freeze sous Libreoffice Writer. Je n'arrive pas à solutionner le problème.
Quelqu'un aurait-il une idée ?
En vous remerciant par avance,
lmaug