Bonjour,

nous utilisons Fedora dans mon entreprise, et ce matin en arrivant impossible de booter sur le nouveau kernel pour deux de nos machines, qui se trouvent être des Dell Optiplex 960. Je suppose qu'il y a un souci avec ce type de matériel, mais à vrai dire je n'ai pas trouvé d'info sous Google, ce noyau étant peut être trop récent ? Je n'ai pas eu de souci avec d'autres pc Dell mais d'un autre modèle. Le souci sous les Optiplex c'est que le boot freeze apres le chargement du dernier service, juste avant l'écran de connexion. A force de reboot nous avons réussi à revenir sur un noyau 2.6.29 et là le boot se passe sans problème. Quelqu'un a-t-il le même problème ? Auriez vous une idée de solution, peut être une option lors du boot ?
Merci d'avance de votre aide.
Il faudrais sans doute aller consulter les rapports de bug ouverts pour ce kernel sur le bugzilla (bugzilla.redhat.com).

Avez-vous essayer de boot en mode texte et de lancer X à la main ?
Booter en mode texte et regardé la sortie de dmesg ?

Y a-t-il quelque chose dans les logs système ?

Edit: oups merci didierg (j'ai corrigé ici pour les générations futures)
apres le chargement du dernier service, juste avant l'écran de connexion
Après le service «atd» (le dernier service chez toi ?) on exécute le rc.local et on démarre X (s'il n'est pas déjà démarré par le boot graphique) et on passe la main au gestion de session graphique.

Cela ressemble à un plantage du serveur X .
Quelle est ta carte vidéo ?
Le clavier est-il mort ?
Que donne
<CTRL><ALT><F2>
pingou wrote:Avez-vous essayer de boot en mode graphique et de lancer X à la main ?
Booter en mode graphique et regardé la sortie de dmesg ?
Booter en mode graphique et lancer X à la main ?

Ne s'agit-il pas plutôt de booter en mode TEXTE (init 3) et de lancer X à la main ?

Pareil pour analyser dmesg....

Quelle est ta carte video (lspci | grep -i vga) ? Quel est le driver utilisé pour celle-ci ?
Bonjour,

Merci pour vos réponses !
J'ai cherché sur le bugzilla de redhat, sans succès pour le moment. Concernant les logs, et la sortie dsmeg, je vais regarder, je vous tiens au courant. Concernant le clavier, au moment du freeze il est effectivement mort, il faut rebooter a la main en forcant le bouton off de la machine.
Enfin, pour la carte graphique, à vrai dire c'est celle intégrée par Dell, la commande lspci me renvoie l'info suivante : 
00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03)
C'est vrai qu'elle ne semble pas terrible, les effets du bureau ont un comportement instable par exemple, je dois les désactiver (ce qui est supportable au boulot :-P) ce qui indique peut être qu'elle n'est pas très bien supportée par Fedora.
Bonjour

Sur un DELL optiplex 755, même problème avec le nouveau kernel PAE. Le PC démarre bien en mode 3 (TEXTE), mais dès qu'on lance l'interface graphique, il freeze. En mode 5 il freeze au chargement de GDM.

Pour le moment, la solution le démarrer avec l'ancien KERNEL, et là pas de problème.
Après test en runlevel 3, le boot se passe effectivement bien mais le freeze se produit dès qu'on lance X...
Je vous donne ci-dessous le résultat de la commande dmesg après le freeze, je n'y ai pas trouvé de message d'erreur clair mais je ne suis pas une spécialiste.
Par ailleurs je n'ai rien trouvé de notable dans les logs système.
Pensez-vous que je dois ouvrir un bug dans le bugzilla de Redhat ?
Merci. 
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.30.5-43.fc11.i686.PAE (mockbuild@x86-6.fedora.phx.redhat.com) (gcc version 4.4.1 20090725 (Red Hat 4.4.1-2) (GCC) ) #1 SMP Thu Aug 27 21:34:36 EDT 2009
KERNEL supported cpus:
  Intel GenuineIntel
  AMD AuthenticAMD
  NSC Geode by NSC
  Cyrix CyrixInstead
  Centaur CentaurHauls
  Transmeta GenuineTMx86
  Transmeta TransmetaCPU
  UMC UMC UMC UMC
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009a800 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 00000000cdbffc00 (usable)
 BIOS-e820: 00000000cdbffc00 - 00000000cdc53c00 (ACPI NVS)
 BIOS-e820: 00000000cdc53c00 - 00000000cdc55c00 (ACPI data)
 BIOS-e820: 00000000cdc55c00 - 00000000d0000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fed00400 (reserved)
 BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
 BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
 BIOS-e820: 0000000100000000 - 0000000128000000 (usable)
DMI 2.5 present.
last_pfn = 0x128000 max_arch_pfn = 0x1000000
MTRR default type: write-back
MTRR fixed ranges enabled:
  00000-9FFFF write-back
  A0000-BFFFF uncachable
  C0000-D7FFF write-protect
  D8000-EFFFF uncachable
  F0000-FFFFF write-protect
MTRR variable ranges enabled:
  0 base 0CDE00000 mask FFFE00000 uncachable
  1 base 0CE000000 mask FFE000000 uncachable
  2 base 0CDD00000 mask FFFF00000 uncachable
  3 base 0D0000000 mask FF0000000 uncachable
  4 base 0E0000000 mask FE0000000 uncachable
  5 disabled
  6 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
init_memory_mapping: 0000000000000000-00000000377fe000
NX (Execute Disable) protection: active
 0000000000 - 0000200000 page 4k
 0000200000 - 0037600000 page 2M
 0037600000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 7000-e000
RAMDISK: 37ca6000 - 37fefe1c
Allocated new RAMDISK: 00a98000 - 00de1e1c
Move RAMDISK from 0000000037ca6000 - 0000000037fefe1b to 00a98000 - 00de1e1b
ACPI: RSDP 000fec00 00024 (v02 DELL  )
ACPI: XSDT 000fc7cb 0008C (v01 DELL    B10K    00000015 ASL  00000061)
ACPI: FACP 000fc8fb 000F4 (v03 DELL    B10K    00000015 ASL  00000061)
ACPI: DSDT ffe9cff8 054AD (v01   DELL    dt_ex 00001000 INTL 20050624)
ACPI: FACS cdbffc00 00040
ACPI: SSDT ffea25c4 000AA (v01   DELL    st_ex 00001000 INTL 20050624)
ACPI: APIC 000fc9ef 00092 (v01 DELL    B10K    00000015 ASL  00000061)
ACPI: BOOT 000fca81 00028 (v01 DELL    B10K    00000015 ASL  00000061)
ACPI: ASF! 000fcaa9 00096 (v32 DELL    B10K    00000015 ASL  00000061)
ACPI: MCFG 000fcb3f 0003E (v01 DELL    B10K    00000015 ASL  00000061)
ACPI: HPET 000fcb7d 00038 (v01 DELL    B10K    00000015 ASL  00000061)
ACPI: TCPA 000fcdd9 00032 (v01 DELL    B10K    00000015 ASL  00000061)
ACPI: ____ 000fce0b 00030 (v01 DELL    B10K    00000015 ASL  00000061)
ACPI: SLIC 000fcbb5 00176 (v01 DELL    B10K    00000015 ASL  00000061)
ACPI: SSDT cdbffc40 001F9 (v01 DpgPmm  Cpu0Ist 00000011 INTL 20050624)
ACPI: SSDT cdc00049 001F9 (v01 DpgPmm  Cpu1Ist 00000011 INTL 20050624)
ACPI: SSDT cdc00452 00190 (v01 DpgPmm    CpuPm 00000010 INTL 20050624)
ACPI: Local APIC address 0xfee00000
3848MB HIGHMEM available.
887MB LOWMEM available.
  mapped low ram: 0 - 377fe000
  low ram: 0 - 377fe000
  node 0 low ram: 00000000 - 377fe000
  node 0 bootmap 0000a000 - 00010f00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
  #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
  #3 [0000400000 - 0000a8f5ac]    TEXT DATA BSS ==> [0000400000 - 0000a8f5ac]
  #4 [000009a800 - 0000100000]    BIOS reserved ==> [000009a800 - 0000100000]
  #5 [0000a90000 - 0000a971a0]              BRK ==> [0000a90000 - 0000a971a0]
  #6 [0000007000 - 000000a000]          PGTABLE ==> [0000007000 - 000000a000]
  #7 [0000a98000 - 0000de1e1c]      NEW RAMDISK ==> [0000a98000 - 0000de1e1c]
  #8 [000000a000 - 0000011000]          BOOTMAP ==> [000000a000 - 0000011000]
found SMP MP-table at [c00fe710] fe710
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  Normal   0x00001000 -> 0x000377fe
  HighMem  0x000377fe -> 0x00128000
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
    0: 0x00000000 -> 0x0000009a
    0: 0x00000100 -> 0x000cdbff
    0: 0x00100000 -> 0x00128000
On node 0 totalpages: 1006489
free_area_init_node: node 0, pgdat c09093c0, node_mem_map c1000000
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 3962 pages, LIFO batch:0
  Normal zone: 1744 pages used for memmap
  Normal zone: 221486 pages, LIFO batch:31
  HighMem zone: 7697 pages used for memmap
  HighMem zone: 771568 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x05] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x01] disabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a701 base: 0xfed00000
SMP: Allowing 8 CPUs, 6 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009a000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at d1000000 (gap: d0000000:10000000)
NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:8 nr_node_ids:1
PERCPU: Embedded 12 pages at c3510000, static data 27868 bytes
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 997016
Kernel command line: ro root=/dev/mapper/vg_maredsou-LogVolSystem rhgb quiet noacpi
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
xsave/xrstor: enabled xstate_bv 0x3, cntxt size 0x240
NR_IRQS:1280
PID hash table entries: 4096 (order: 12, 16384 bytes)
Fast TSC calibration using PIT
Detected 3158.944 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
allocated 24248320 bytes of page_cgroup
please try cgroup_disable=memory option if you don't want
Initializing HighMem for node 0 (000377fe:00128000)
Memory: 3952004k/4849664k available (3329k kernel code, 73036k reserved, 2081k data, 412k init, 3117060k highmem)
virtual kernel memory layout:
    fixmap  : 0xffc55000 - 0xfffff000   (3752 kB)
    pkmap   : 0xff800000 - 0xffa00000   (2048 kB)
    vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
    lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
      .init : 0xc0953000 - 0xc09ba000   ( 412 kB)
      .data : 0xc0740760 - 0xc0948c58   (2081 kB)
      .text : 0xc0400000 - 0xc0740760   (3329 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
hpet clockevent registered
HPET: 8 timers in total, 5 timers will be used for per-cpu timer
Calibrating delay loop (skipped), value calculated using timer frequency.. 6317.88 BogoMIPS (lpj=3158944)
Security Framework initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20090320
ftrace: converting mcount calls to 0f 1f 44 00 00
ftrace: allocating 18962 entries in 38 pages
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Duo CPU     E8500  @ 3.16GHz stepping 0a
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6317.45 BogoMIPS (lpj=3158729)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Core(TM)2 Duo CPU     E8500  @ 3.16GHz stepping 0a
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (12635.34 BogoMIPS).
sizeof(vma)=88 bytes
sizeof(page)=32 bytes
sizeof(inode)=348 bytes
sizeof(dentry)=132 bytes
sizeof(ext3inode)=504 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=180 bytes
sizeof(task_struct)=3272 bytes
CPU0 attaching sched-domain:
 domain 0: span 0-1 level MC
  groups: 0 1
CPU1 attaching sched-domain:
 domain 0: span 0-1 level MC
  groups: 1 0
net_namespace: 1096 bytes
Booting paravirtualized kernel on bare hardware
regulator: core version 0.5
Time: 11:12:31  Date: 09/08/09
NET: Registered protocol family 16
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI Warning (tbutils-0246): Incorrect checksum in table [TCPA] - 00, should be 7F [20090320]
ACPI: ACPI Dock Station Driver: 1 docks/bays found
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:02.0: reg 10 64bit mmio: [0xfe800000-0xfebfffff]
pci 0000:00:02.0: reg 18 64bit mmio: [0xd0000000-0xdfffffff]
pci 0000:00:02.0: reg 20 io port: [0xec90-0xec97]
pci 0000:00:02.1: reg 10 64bit mmio: [0xfe700000-0xfe7fffff]
pci 0000:00:03.0: reg 10 64bit mmio: [0xfeda6000-0xfeda600f]
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:03.2: reg 10 io port: [0xfe80-0xfe87]
pci 0000:00:03.2: reg 14 io port: [0xfe90-0xfe93]
pci 0000:00:03.2: reg 18 io port: [0xfea0-0xfea7]
pci 0000:00:03.2: reg 1c io port: [0xfeb0-0xfeb3]
pci 0000:00:03.2: reg 20 io port: [0xfef0-0xfeff]
pci 0000:00:03.3: reg 10 io port: [0xec98-0xec9f]
pci 0000:00:03.3: reg 14 32bit mmio: [0xfe6d8000-0xfe6d8fff]
pci 0000:00:19.0: reg 10 32bit mmio: [0xfe6e0000-0xfe6fffff]
pci 0000:00:19.0: reg 14 32bit mmio: [0xfe6d9000-0xfe6d9fff]
pci 0000:00:19.0: reg 18 io port: [0xecc0-0xecdf]
pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
pci 0000:00:19.0: PME# disabled
pci 0000:00:1a.0: reg 20 io port: [0xff20-0xff3f]
pci 0000:00:1a.1: reg 20 io port: [0xff00-0xff1f]
pci 0000:00:1a.2: reg 20 io port: [0xfc00-0xfc1f]
pci 0000:00:1a.7: reg 10 32bit mmio: [0xfe6da000-0xfe6da3ff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: reg 10 64bit mmio: [0xfe6dc000-0xfe6dffff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0xff80-0xff9f]
pci 0000:00:1d.1: reg 20 io port: [0xff60-0xff7f]
pci 0000:00:1d.2: reg 20 io port: [0xff40-0xff5f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xff980000-0xff9803ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.2: reg 10 io port: [0xfe00-0xfe07]
pci 0000:00:1f.2: reg 14 io port: [0xfe10-0xfe13]
pci 0000:00:1f.2: reg 18 io port: [0xfe20-0xfe27]
pci 0000:00:1f.2: reg 1c io port: [0xfe30-0xfe33]
pci 0000:00:1f.2: reg 20 io port: [0xfec0-0xfedf]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xff970000-0xff9707ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 10 64bit mmio: [0xfe6db000-0xfe6db0ff]
pci 0000:00:1f.3: reg 20 io port: [0xece0-0xecff]
pci 0000:00:01.0: bridge 32bit mmio: [0xfe500000-0xfe5fffff]
pci 0000:00:1c.0: bridge 32bit mmio: [0xfe400000-0xfe4fffff]
pci 0000:00:1c.1: bridge 32bit mmio: [0xfe300000-0xfe3fffff]
pci 0000:00:1e.0: transparent bridge
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 15)
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 24, 25, 26, 27, 28, 0
hpet0: 8 comparators, 64-bit 14.318180 MHz counter
hpet: hpet2 irq 24 for MSI
hpet: hpet3 irq 25 for MSI
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 9 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: ioport range 0x800-0x85f has been reserved
system 00:01: ioport range 0xc00-0xc7f has been reserved
system 00:01: ioport range 0x860-0x8ff has been reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0:   IO window: disabled
pci 0000:00:01.0:   MEM window: 0xfe500000-0xfe5fffff
pci 0000:00:01.0:   PREFETCH window: disabled
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.0:   IO window: disabled
pci 0000:00:1c.0:   MEM window: 0xfe400000-0xfe4fffff
pci 0000:00:1c.0:   PREFETCH window: disabled
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
pci 0000:00:1c.1:   IO window: disabled
pci 0000:00:1c.1:   MEM window: 0xfe300000-0xfe3fffff
pci 0000:00:1c.1:   PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:04
pci 0000:00:1e.0:   IO window: disabled
pci 0000:00:1e.0:   MEM window: disabled
pci 0000:00:1e.0:   PREFETCH window: disabled
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:01: resource 1 mem: [0xfe500000-0xfe5fffff]
pci_bus 0000:02: resource 1 mem: [0xfe400000-0xfe4fffff]
pci_bus 0000:03: resource 1 mem: [0xfe300000-0xfe3fffff]
pci_bus 0000:04: resource 3 io:  [0x00-0xffff]
pci_bus 0000:04: resource 4 mem: [0x000000-0xffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 3367k freed
Simple Boot Flag at 0x7a set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
type=2000 audit(1252408353.071:1): initialized
highmem bounce pool size: 64 pages
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1639
SELinux:  Registering netfilter hooks
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
pcieport-driver 0000:00:01.0: irq 29 for MSI/MSI-X
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: irq 30 for MSI/MSI-X
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.1: irq 31 for MSI/MSI-X
pcieport-driver 0000:00:1c.1: setting latency timer to 64
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
acpiphp_glue: can't get bus number, assuming 0
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button [PWRF]
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
ACPI: Power Button [VBTN]
Monitor-Mwait will be used to enter C-1 state
processor ACPI_CPU:00: registered as cooling_device0
processor ACPI_CPU:01: registered as cooling_device1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel Q45/Q43 Chipset
agpgart-intel 0000:00:00.0: detected 32764K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial 0000:00:03.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
0000:00:03.3: ttyS1 at I/O 0xec98 (irq = 17) is a 16550A
brd: module loaded
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input2
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ahci 0000:00:1f.2: irq 32 for MSI/MSI-X
ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x27 impl RAID mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pio ems 
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 abar m2048@0xff970000 port 0xff970100 irq 32
ata2: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 32
ata3: SATA max UDMA/133 abar m2048@0xff970000 port 0xff970200 irq 32
ata4: DUMMY
ata5: DUMMY
ata6: SATA max UDMA/133 abar m2048@0xff970000 port 0xff970380 irq 32
Fixed MDIO Bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.7: irq 22, io mem 0xfe6da000
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.30.5-43.fc11.i686.PAE ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.7
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xff980000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.30.5-43.fc11.i686.PAE ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.7
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000ff20
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.30.5-43.fc11.i686.PAE uhci_hcd
usb usb3: SerialNumber: 0000:00:1a.0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 17, io base 0x0000ff00
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.30.5-43.fc11.i686.PAE uhci_hcd
usb usb4: SerialNumber: 0000:00:1a.1
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
uhci_hcd 0000:00:1a.2: setting latency timer to 64
uhci_hcd 0000:00:1a.2: UHCI Host Controller
uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1a.2: irq 22, io base 0x0000fc00
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.30.5-43.fc11.i686.PAE uhci_hcd
usb usb5: SerialNumber: 0000:00:1a.2
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000ff80
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: UHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.30.5-43.fc11.i686.PAE uhci_hcd
usb usb6: SerialNumber: 0000:00:1d.0
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000ff60
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: UHCI Host Controller
usb usb7: Manufacturer: Linux 2.6.30.5-43.fc11.i686.PAE uhci_hcd
usb usb7: SerialNumber: 0000:00:1d.1
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ff40
usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb8: Product: UHCI Host Controller
usb usb8: Manufacturer: Linux 2.6.30.5-43.fc11.i686.PAE uhci_hcd
usb usb8: SerialNumber: 0000:00:1d.2
usb usb8: configuration #1 chosen from 1 choice
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 2 ports detected
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
rtc_cmos 00:05: RTC can wake from S4
rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one day, 242 bytes nvram, hpet irqs
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
Using IPI No-Shortcut mode
PM: Resume from disk failed.
registered taskstats version 1
  Magic number: 9:950:225
Initalizing network drop monitor service
ata3: SATA link down (SStatus 4 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: WDC WD3200AAKS-75L9A0, 02.03E02, max UDMA/133
ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      WDC WD3200AAKS-7 02.0 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
usb 5-1: new low speed USB device using uhci_hcd and address 2
usb 5-1: New USB device found, idVendor=413c, idProduct=2106
usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 5-1: Product: Dell QuietKey Keyboard
usb 5-1: Manufacturer: Dell
usb 5-1: configuration #1 chosen from 1 choice
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATAPI: HL-DT-ST DVD+/-RW GH50N, B101, max UDMA/100, ATAPI AN
ata2.00: configured for UDMA/100
scsi 1:0:0:0: CD-ROM            HL-DT-ST DVD+-RW GH50N    B101 PQ: 0 ANSI: 5
input: Dell Dell QuietKey Keyboard as /devices/pci0000:00/0000:00:1a.2/usb5/5-1/5-1:1.0/input/input3
generic-usb 0003:413C:2106.0001: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell QuietKey Keyboard] on usb-0000:00:1a.2-1/input0
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr 1:0:0:0: Attached scsi generic sg1 type 5
Freeing unused kernel memory: 412k freed
Write protecting the kernel text: 3332k
Write protecting the kernel read-only data: 1612k
[drm] Initialized drm 1.1.0 20060810
i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
i915 0000:00:02.0: setting latency timer to 64
i915 0000:00:02.0: irq 33 for MSI/MSI-X
usb 5-2: new low speed USB device using uhci_hcd and address 3
allocated 1600x1200 fb: 0x02020000, bo f7146f60
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 200x75
usb 5-2: New USB device found, idVendor=0461, idProduct=4d15
usb 5-2: New USB device strings: Mfr=0, Product=2, SerialNumber=0
usb 5-2: Product: USB Optical Mouse
usb 5-2: configuration #1 chosen from 1 choice
[drm] DAC-6: set mode 1600x1200 15
input: USB Optical Mouse as /devices/pci0000:00/0000:00:1a.2/usb5/5-2/5-2:1.0/input/input4
generic-usb 0003:0461:4D15.0002: input,hidraw1: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:1a.2-2/input0
fb0: inteldrmfb frame buffer device
registered panic notifier
[drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
EXT4-fs: barriers enabled
kjournald2 starting: pid 78, dev dm-1:8, commit interval 5 seconds
EXT4-fs: delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs: mounted filesystem dm-1 with ordered data mode
type=1404 audit(1252408355.927:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
SELinux: 8192 avtab hash slots, 128893 rules.
SELinux: 8192 avtab hash slots, 128893 rules.
SELinux:  8 users, 11 roles, 2768 types, 129 bools, 1 sens, 1024 cats
SELinux:  74 classes, 128893 rules
SELinux:  Completing initialization.
SELinux:  Setting up existing superblocks.
SELinux: initialized (dev dm-1, type ext4), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
type=1403 audit(1252408356.062:3): policy loaded auid=4294967295 ses=4294967295
udev: starting version 141
e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.4-k4
e1000e: Copyright (c) 1999-2008 Intel Corporation.
e1000e 0000:00:19.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
e1000e 0000:00:19.0: setting latency timer to 64
e1000e 0000:00:19.0: irq 34 for MSI/MSI-X
iTCO_vendor_support: vendor-support=0
dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
ACPI: WMI: Mapper loaded
input: PC Speaker as /devices/platform/pcspkr/input/input5
0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:24:e8:fb:ff:f8
0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
0000:00:19.0: eth0: MAC: 8, PHY: 8, PBA No: 2021ff-0ff
pata_acpi 0000:00:03.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
pata_acpi 0000:00:03.2: setting latency timer to 64
pata_acpi 0000:00:03.2: PCI INT C disabled
i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: failed to reset NO_REBOOT flag, reboot disabled by hardware
iTCO_wdt: No card detected
parport_pc 00:06: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
ppdev: user-space parallel port driver
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
HDA Intel 0000:00:1b.0: setting latency timer to 64
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input6
device-mapper: multipath: version 1.0.5 loaded
EXT4 FS on dm-1, internal journal on dm-1:8
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 2097144k swap on /dev/mapper/vg_maredsou-LogVolSwap.  Priority:-1 extents:1 across:2097144k 
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
e1000e 0000:00:19.0: irq 34 for MSI/MSI-X
e1000e 0000:00:19.0: irq 34 for MSI/MSI-X
ADDRCONF(NETDEV_UP): eth0: link is not ready
e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
0000:00:19.0: eth0: 10/100 speed: disabling TSO
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
CIFS: Unknown mount option umask
SELinux: initialized (dev cifs, type cifs), uses genfs_contexts
CIFS: Unknown mount option umask
SELinux: initialized (dev cifs, type cifs), uses genfs_contexts
eth0: no IPv6 routers present
1- quand tu démarres X essai un startx 1> startx.log 2>&1 et poste nous le fichier pour voir les erreurs
2- tu as rien dans Xorg.0.log ?

Je pense que le bug sur le bugzilla sera une bonne idée oui 🙂
(D'autant plus si tu n'as pas de problème sur un kernel 2.6.29
ok merci pour ces conseils, je vais essayer et je posterais le fichier. Comme le poste est utilisé je vais devoir attendre un peu pour relancer X.

Pour le Xorg.0.log j'ai un .old qui commence par : 
Current Operating System: Linux maredsou 2.6.30.5-43.fc11.i686.PAE #1 SMP Thu Aug 27 21:34:36 EDT 2009 i686
donc je suppose que c'est bien celui, mais le seul message d'erreur que je trouve (si je ne me trompes pas, c'est préfixé par EE) est celui là, répété deux fois : 
(EE) intel(0): max_gtt_map_size: 53372kb
Est ce que tu veux la totalité du fichier ? Il est assez long à vrai dire, mais je peux le coller si ça aide.
Pour le bug, je vais peut être attendre d'avoir les résultats de ta commande au démarrage de X ? ce qui m'ennuie c'est que sans message d'erreur ça va pas être un super rapport de bug :-P or je préfère être le plus précise possible !
J'ai pu récuperer les logs au start x, voici ce que ça donne : 
X.Org X Server 1.6.1.901 (1.6.2 RC 1)
Release Date: 2009-5-8
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.18-128.1.6.el5 i686 
Current Operating System: Linux maredsou 2.6.30.5-43.fc11.i686.PAE #1 SMP Thu Aug 27 21:34:36 EDT 2009 i686
Kernel command line: ro root=/dev/mapper/vg_maredsou-LogVolSystem rhgb quiet
Build Date: 18 May 2009  02:47:59PM
Build ID: xorg-x11-server 1.6.1.901-1.fc11 
    Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Tue Sep  8 17:48:40 2009
(==) Using default built-in configuration (30 lines)
(EE) intel(0): max_gtt_map_size: 53372kb.
Setting master 
(EE) intel(0): max_gtt_map_size: 53372kb.
ça ressemble au même message que le Xorg.0.log non ?
En cherchant ce message dans le bugzilla, je suis tombée sur ce bug report : le dernier commentateur à l'air d'avoir le même problème que moi. Selon vous je rajoute un commentaire à ce bug ou j'en ouvre un autre ?
Merci encore pour votre aide.
Petite précision, je viens de tester et en fait j'ai deux Optiplex 960 avec exactement le même processeur, mais je viens de voir que l'un est en kernel de type i586 et l'autre i686...

Déjà je ne comprend pas comment c'est possible, mis à part peut être que l'un des deux est en F11 suite à un upgrade packagekit et l'autre a été installé via un cd de Fedora.

Ensuite, celui en i586 boot sans problème sur le kernek 2.6.30...

Par ailleurs, celui qui pose problème à un kernel-PAE, pas celui qui marche (je ne sais pas si c'est lié).

Savez vous s'il est possible de remplacer le kernel 686 par un 586 puisque ça a l'air de marcher ?

Merci d'avance !
Le kernel PAE est installé sur les PC qui ont plus de 3 Go de RAM.

Donc à voir
Salut,
lolofurieux wrote:Le kernel PAE est installé sur les PC qui ont plus de 3 Go de RAM.
Non, j'ai un noyau PAE sur P4 avec 2Gigas de ram.

Et j'ai aussi le même problème que Linuxline : démarrage avec le nouveau noyau 2.6.30 très très lent, ça passe en init 3 mais le lancement de x est impossible...
Ce PC est un fixe made in "chez moi".
Avec un fixe
made in "chez moi"
architecture amd (proco et chipset), 2go de ram aussi (m'a installé PAE en prévision de mes achats? :-D ) et CG Nvidia.
Le kernel 2.6.30 boot sans aucun soucis, il semble que celà touche les architectures Intel. Pourtant sur un P4 le chipset est surement sans rapport avec celui des Dell cités (CG 4500HD je suppose au passage).
Un jeu d'instruction propre à Intel qui cause soucis?
Problème entre le pilote et le noyau PAE sans doute... il y en a pas mal qui l'on avec le pilote nvidia... Je ne parle même pas de ceux en pilote propriétaire ATI, faut que je fasse des investigations...
Pour info j'utilise des versions récentes du .run de Nvidia, pas de kmod, ce qui veux dire que je dois réinstaller à chaque changement de kernel, ce qui va vite finalement bien qu'un poil plus compliqué.
Carte Ati avec le pilote libre, résolution en 1920x1080...
4 jours plus tard
on est deja dessus
https://bugzilla.redhat.com/show_bug.cgi?id=521574
(probablement un probleme kernel 2.6.30 PAE et intel chipset)
merci de voter pour remonter le bug

la seule solution pour le moment c'est d'installer le 2.6.30 non PAE (pas interessant pour les machines > 3Go de ram) en attendant un patch.
Bonjour,

merci pour toutes les réponses ! Je suis allée voter pour le bug, apparemment c bien en rapport avec la carte graphique Intel, beaucoup des gens qui ont laissé des commentaires ont des config Dell similaire. A suivre donc !